Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

Safety assessment of the film boiling chemical vapor infiltration (FB-CVI) process through a system-theoretic accident model and process (STAMP)

Film boiling chemical vapor infiltration (FB-CVI) is considered as one of the fastest process methodologies for manufacturing carbon-carbon (C–C) composite products and possesses various advantages compared to conventional methodologies. However, there are safety concerns associated with this process for large-scale manufacturing, mainly owing to the intrinsic nature of the precursor and the process conditions. Considering the multifunctional interactions of the various systems during the process, a system-theoretic process analysis (STPA)/system theoretic accident model and process (STAMP) model is used to perform a safety analysis of the hazardous states of the FB-CVI process at the system level. As a case study, the FB-CVI process equipment employed for the manufacturing of C–C composites is considered. The safety constraints present in the system are assessed for adequacy through a hazard analysis by STPA/STAMP. The analysis through STPA/STAMP demonstrated the capability to create proactive strategies for the design and realization of process equipment that can be employed to manufacture C–C composite products through the FB-CVI process.     

固相萃取-气质联用法测定固体废物浸出液中的二硝基苯

建立了一种利用固相萃取法对固体废物浸出液(TCLP)中二硝基苯进行萃取,DB-5石英毛细管柱(30 m×0.25 mm×0.25μm)进行分离,质谱检测器检测二硝基苯的方法。方法在0.002 0~0.020 0 mg/L之间线性关系良好,二硝基苯三种同分异构体的检出限均为0.5μg/L,模拟样品加标回收率为93%~96%,RSD≤2%;实际固体废物样品测定的加标回收率为95%~98%。     

Challenges for modelling and integrating environmental performances in concept design: the case of an automotive component lightweighting

The objective of this paper is to discuss the main barriers for modelling and integrating the environmental performances in the automotive concept design. Incorporating environmental assessment in the early design phase of a vehicle component is known as an important challenge that car makers need to face in order to develop more sustainable design solutions; in this regard, the Life Cycle Assessment is the most widespread methodology for the environmental assessment and comparison of alternatives. The present work illustrates the combination of such methodology with the traditional design procedure at two different levels of the component design phase, material choice and concept design. In particular, the potential benefits originated by a lightweight solution for the automotive component Throttle Body are evaluated by considering environmental and technical implications at the same level. The case study shows that a multi-disciplinary approach for design effectively allows the integration of the environmental issue in the company’s established procedures. However, interpretation of results is still a challenging aspect due to the inevitable contradicting elements which should not discourage to develop comprehensive sustainability assessment within the early design stage.     

湖北省2008年初低温雨雪冰冻过程气候特征分析

2008年初，湖北省出现了严重的低温雨雪冰冻灾害，直接经济损失高达110亿元以上，有必要对灾害期间的气候特征进行系统、科学的分析和总结。对湖北省76个气象站2008年1月12日～2月3日气温、降水（雪）、日照以及低温持续日数等要素进行时空间差异分析及历史与同期比较，并选取10个代表站历史上所有低温雨雪天气过程，对其过程持续低温日数、最长连续雨雪日数、过程极端低温进行比较分析。结果表明：（1）此次过程的平均气温异常偏低，该省大部为-1～-2℃，比常年同期偏低4～6℃，为各站历史同期最低，其中主要是最高气温异常偏低所致，但极端低温并不低；（2）降雪过程频繁，雨雪量异常偏多；（3）低温冰冻持续时间长，该省大部在16～22 d，位于历史第一；（4）日照异常偏少。持续而稳定的大气环流异常形势是湖北省大范围低温雨雪天气的直接原因。     

火灾高温下CFRP加固钢筋混凝土梁温度场分析

综合国外CFRP加固混凝土结构抗火试验相关研究,总结了CFRP的高温热工性能参数。用ANSYS软件对火灾高温下不同情况(无防火保护层和有防火保护层)和不同工况(防火涂料涂抹形式)下CFRP加固后的钢筋混凝土梁进行了温度场数值模拟研究。结果表明,防火涂料厚40 mm时,梁耐火极限可达2.5小时以上,且底面和两侧面全面涂抹防火涂料的防火效果最好。本文研究有助于进一步深入认识CFRP加固钢筋混凝土结构在高温下的力学性能和耐火极限,且对CFRP加固后的结构防火设计具有一定的指导意义。     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

EFFECTS OF ADJACENT AGRICULTURAL ACTIVITIES AND WATERSHED CHARACTERISTICS ON STREAM MACROINVERTEBRATE COMMUNITIES1

Benthic macroinvertebrate communities in streams adjacent to cornfields, streams where cows had unrestricted access, and reference locations without agriculture were compared to examine the effects of local land use and land use/land cover in the watershed. At each local site, macroinvertebrates and a variety of habitat parameters were measured upstream, adjacent, downstream, and farther downstream of the local land use. A geographic information system (GIS) was used to calculate drainage basin area, land use/land cover percentages in each basin, and the distance from sample sites to the stream source. Three‐way analysis of covariance (ANCOVA) tests with date, site type, and sampling location as main effects were used to explore differences in macroinvertebrate metrics using median substrate size, percent hay/pasture area, and stream depth as covariates. The covariates significantly improved model fit and showed that multiple contributing factors influence community composition. Local impacts were greatest at sites where cows had access, probably because of sedimentation and embeddedness in the substrate. Differences between the upstream and the adjacent and downstream locations were not as great as expected, perhaps because upstream recolonization was reduced by agricultural impacts or because of differences in the intensity or proximity of agriculture to riparian areas in the watershed. The results underscore the importance of both local and watershed factors in controlling stream community composition.     

Study on Assessing Economic Vulnerability of Small Island Regions

The main purpose of this study is to assess economic vulnerability of small island development regions as part of their sustainability constraints. By combining economic and environmental time series data, we assessed a composite index of economic vulnerability which is constructed from three exogenous variables, namely economic exposure, economic remoteness, and economic impact of environmental and natural disasters. We used the Amami Islands, Kagoshima Prefecture, Japan as the case studies for this paper.The results indicated that using a gross island products based valuation index, Kikaijima is the most vulnerable island in the Amami Islands with a composite economic vulnerability index (CEVI) value of 0.678, while by using a per capita based index, Okinoerabujima is considered the most vulnerable island with a CEVI value of 0.680. From the results we also revealed that smaller islands have relative higher vulnerability than the bigger one, which also confirms some previous country-level vulnerability studies.However, it is matter of fact that some islands that have relatively high vulnerability also have good economic performance as shown by their per capita income. In this regard, it can be argued that the success of these small islands could have been achieved in spite of and not because of their inherent vulnerability conditions as an indicator of sustainability constraint. Regarding these findings, we also examined a comparison between vulnerability results and the preliminary concept of an island's resilience in order to capture another perspective on sustainability assessment in a small island region.