Fe3O4/纤维素纳米复合材料的制备及其对亚甲基蓝的吸附

采用化学沉淀法与液相复合方法联合制备磁性无机-有机Fe3O4/纤维素复合材料。采用扫描电镜及红外光谱对其进行结构表征,以亚甲基蓝溶液为模拟废水,考察了接触时间、溶液初始pH及反应温度等因素对其吸附性能的影响,分别用准一级动力学和准二级动力学方程对数据进行拟合。结果表明,温度为22℃,溶液初始pH为7.55,Fe3O4/纤维素纳米复合材料加量为0.67 g·L-1,接触时间2 h,30 mg·L-1亚甲基蓝脱色率达99.20%,准二级动力学模型能更好地描述Fe3O4/纤维素复合材料对亚甲基蓝的吸附行为。同时,Fe3O4/纤维素纳米复合材料具有较强的磁性,可通过简单的磁铁吸引作用进行分离。     

木质纤维素原料预处理技术研究近况

木质纤维素的结构导致其不易降解。通过酸处理、碱处理、液态高温水技术、爆破处理、湿式氧化、超临界CO2处理、生物降解等预处理手段,可使后续过程的效率大大提高。较为全面地对国内外木质纤维素原料预处理技术的研究近况做了总结,主要对国外学者的试验方法和现象分析进行了简要描述,并对萼合于我国的方法提出了自己的观点。     

高效纤维素分解菌在蔬菜-花卉秸秆联合好氧堆肥中的应用

以滇池流域典型的蔬菜废物和花卉秸秆为堆肥原料,以本实验室筛选、保存的17株纤维素降解菌和1株购买的产黄纤维单胞菌(Cellulomonas Flavigena)为复合接种剂,对不同接种条件和控温条件下的联合堆肥中试进行了研究.实验结果表明,在一次发酵的初始阶段,以体积分数0.5%的接种量向堆肥中接种纤维素降解复合菌剂可有效提高发酵过程堆料中纤维素降解菌的种群密度,并使其迅速成为优势菌群,尤其是当堆体处于控温55℃的工况条件时,其菌群密度可保持在3.84×10⁹～1.80×10¹⁰CFU/g;在二次发酵的初始阶段,以体积分数1%的接种量接种,可有效提高二次发酵阶段堆温的回升.对堆料中木质素和纤维素含量以及堆肥终产物的粒径分布指标--过筛率的检测表明,接种的复合纤维素降解菌可有效地降解堆料中的木质纤维素,接种处理中纤维素的降解率比不接种处理高23.64%,接种处理堆肥终产物的过筛率(2.0 cm)比不接种处理高18.28%.研究表明,用纤维素降解复合菌剂进行二次接种二次发酵,能够有效地促进蔬菜-花卉秸秆联合好氧堆肥中物料的纤维素组分的降解,达到加快堆肥进程,提高堆肥品质的目的.     

固相餐厨垃圾厌氧发酵特性

为了研究固相餐厨垃圾厌氧发酵产甲烷特性,对固相餐厨垃圾进行批式厌氧发酵实验,主要考察了pH、VFA、COD以及纤维素酶活的变化情况,并运用修正Gompertz模型对其产气模型进行动力学拟合.实验结果表明,缓冲溶液的添加可明显促进厌氧发酵产甲烷.在添加缓冲溶液条件下,污泥与餐厨垃圾比例为2∶1,1∶1,2∶3和1∶2时,餐厨垃圾都能很好地进行厌氧发酵产甲烷,最大产甲烷产量分别为594.66、449.74、392.93和333.36 mL/g TS.采用修正Gompertz模型分别对2∶1、1∶1、2∶3和1∶2实验组产甲烷曲线进行拟合,得到产甲烷潜力分别为567.57、437.89、381.12和305.60 mL/g TS,最大产甲烷速率分别为89.38、59.81、47.26和25.80 mL/(d·g VS).对厌氧发酵过程中纤维素酶活的变化进行了研究,结果表明,CMC酶活性在提高餐厨垃圾厌氧发酵过程中纤维素的降解起重要作用.     

降解纤维素产甲烷的四菌复合系

自然环境中通常是微生物群落协同完成纤维素的降解,构建可降解纤维素的混菌体系是认识微生物相互作用的关键.利用富集培养法,结合变性梯度凝胶电泳(DGGE)指纹检测技术以及厌氧滚管技术,建立了一种筛选简单降解纤维素产甲烷复合菌系的方法.利用此方法从青藏高原若尔盖高寒湿地分离到一个由4株菌构成的降解纤维素产甲烷的稳定菌系.结果表明,该复合菌系由纤维素水解菌Clostridium glycolicum、非纤维素水解菌Trichococcus flocculiformis和Parabacteroides merdae、产甲烷古菌Methanobacterium subterraneum等具有不同功能的4种菌株组成,且在这4株菌的共同作用下可将纤维素直接转化为CH4.该简单复合系的获得为今后纤维素转化甲烷复合菌系的代谢控制和遗传改造提供了一个平台.     

纸板碳化电极提高生物电化学系统产电效率微生物机理研究

采用Solexa高通量测序技术和蛋白定量方法,分析了碳化纤维素纸板制备的层状波纹碳(LCC)电极与石墨板(GP)电极在生物电化学系统运行过程形成的生物膜微生物群落结构和生物量差异.结果表明,LCC电极良好的生物电化学性能不仅取决于其良好的导电性能,还与其表面生物膜微生物群落结构有关;LCC电极表面生物膜微生物量高,且对产电微生物的富集效果好.LCC电极与GP电极表面生物膜分别得到16S rRNA基因V3区优化序列12643条和12837条,经97%相似度归并后获得的OTUs数量分别为2786和3130;α多样性分析显示,GP电极生物膜微生物多样性相对更丰富.Proteobacteria、Firmicutes和Bacteroidetes在两种电极生物膜中含量最为丰富,这3个门细菌序列数分别占总序列数的76%(LCC)和85%(GP).在属分类水平上,LCC电极生物膜由383个属的细菌构成,而GP电极生物膜则有456个属.深入分析电极生物膜微生物群落结构有助于进一步认识LCC电极提高生物电化学系统产电效率的机理.     

生物膜法污水处理用新型纤维素载体的制备与性能

以麦草浆粕为原料,研究开发出了一种适用于生物膜法污水处理的多孔生物膜载体.实验通过对麦草浆粕碱化、黄化制备出酯化均匀的纤维素粘胶,并在此基础上选取合适的发泡成孔技术和纤维素再生工艺得到多孔纤维素载体成品.实验考察了各制备条件对载体性能的影响,总结出了该工艺下性能最优的载体的制备条件.研究结果表明,制得载体的孔隙率可达85%,比表面积在11m2·g-1以上,孔径从100μm～800μm均可人为控制.制得的多孔纤维素载体成本低廉,用于污水处理效果十分良好.     

季铵化木屑纤维素的制备及其对水中苯酚的吸附性能研究

以3-氯-2-羟丙基三甲基氯化铵(CTA)为醚化剂,对木屑纤维素进行了改性。探讨了改性木屑纤维素用量、pH值、吸附温度、吸附时间和苯酚初始浓度等因素对静态吸附效果的影响。结果表明,木屑纤维素经改性后,对水中的苯酚的吸附过程存在化学吸附,对水中的苯酚的吸附容量得到明显提高。     

Effects of Smoke Emissions from a Charcoal Kiln on the Functioning of Forest Soil Systems: A Microcosm Study

Long-term charcoal production in small private charcoal kilns (CK) in Eastern Bieszczady Mts. (SE Poland) can cause local smoke contamination of the ambient forest environment. Responses of model soil systems, contaminated or not contaminated by CK smoke, to contrasting combinations of hydrothermic regimes were compared in laboratory microcosms (respiration of soil community, decomposition rate of soil organic matter and cotton stripes, herb seeds germination were studied). The majority of the obtained data show a markedly higher level of soil biological activity in the CK versus the control series. In some cases CK and control soil systems show different patterns of reactions to the tested combinations of microclimate regime. These phenomena should at least partly be attributed to the effects of CK pollution.     

Biodegradable plastic made from soybean products. II. Effects of cross-linking and cellulose incorporation on mechanical properties and water absorption

Soy isolate was treated with formaldehyde and glyoxal at 1.0, 2.5, and 5.0% (w/w isolate) and with adipic and acetic anhydrides. The materials were then compression-molded into plastic tensile bars and tested for tensile and yield strength, percentage elongation, Young's modulus, and water absorption. Treatment with 5% formaldehyde increased the tensile strength significantly, to 4.9 kg/mm², compared with the untreated sample (3.7 kg/mm²). The yield strength increased slightly, to 0.68 kg/mm². Elongation was significantly less after treatment with formaldehyde. Young's modulus increased after treatment and leveled off at 174 kg/mm². Water absorption decreased as the formaldehyde concentration increased. Treatment with either glyoxal or adipic/acetic anhydride had a detrimental effect on the mechanical properties of the plastic specimens. Water absorption was decreased by glyoxal treatment but was not affected by adipic/acetic anhydride treatment. Long-fiber (lf), short-fiber (sf), and microcrystalline (mc) cellulose were incorporated into soy isolate at various levels. Cellulose addition decreased the percentage elongation and increased the rigidity of the plastic. All three cellulose additions increased Young's modulus. The tensile strength increased with the addition of sf-cellulose to soy isolate; lf-cellulose decreased the tensile strength, whereas the incorporation of mc-cellulose did not have a significant effect. The yield strength increased slightly with the addition of sf-cellulose and was less affected by the addition of lf- or mc-cellulose. All three types of cellulose slightly decreased water absorption at ca. 15% content.Journal Paper No. J-15563 of the Iowa Agriculture and Home Economics Experiment Station, Ames; Project No. 2863.