Carbonyl emissions from heavy-duty diesel vehicle exhaust in China and the contribution to ozone formation potential

Fifteen heavy-duty diesel vehicles were tested on chassis dynamometer by using typical heavy duty driving cycle and fuel economy cycle. The air from the exhaust was sampled by 2,4- dinitrophenyhydrazine cartridge and 23 carbonyl compounds were analyzed by high performance liquid chromatography. The average emission factor of carbonyls was 97.2 mg/km, higher than that of light-duty diesel vehicles and gasoline-powered vehicles. Formaldehyde, acetaldehyde, acetone and propionaidehyde were the species with the highest emission factors. Main influencing factors for carbonyl emissions were vehicle type, average speed and regulated emission standard, and the impact of vehicle loading was not evident in this study. National emission of carbonyls from diesel vehicles exhaust was calculated for China, 2011, based on both vehicle miles traveled and fuel consumption. Carbonyl emission of diesel vehicle was estimated to be 45.8 Gg, and was comparable to gasolinepowered vehicles （58.4 Gg）. The emissions of formaldehyde, acetaldehyde and acetone were 12.6, 6.9, 3.8 Gg, respectively. The ozone formation potential of carbonyls from diesel vehicles exhaust was 537 mg O3/km, higher than 497 mg O3/km of none-methane hydrocarbons emitted from diesel vehicles.     

Morphology and composition of particles emitted from a port fuel injection gasoline vehicle under real-world driving test cycles

Traffic vehicles, many of which are powered by port fuel injection (PFI) engines, are major sources of particulate matter in the urban atmosphere. We studied particles from the emission of a commercial PFI-engine vehicle when it was running under the states of cold start, hot start, hot stabilized running, idle and acceleration, using a transmission electron microscope and an energy-dispersive X-ray detector. Results showed that the particles were mainly composed of organic, soot, and Ca-rich particles, with a small amount of S-rich and metal-containing particles, and displayed a unimodal size distribution with the peak at 600?nm. The emissions were highest under the cold start running state, followed by the hot start, hot stabilized, acceleration, and idle running states. Organic particles under the hot start and hot stabilized running states were higher than those of other running states. Soot particles were highest under the cold start running state. Under the idle running state, the relative number fraction of Ca-rich particles was high although their absolute number was low. These results indicate that PFI-engine vehicles emit substantial primary particles, which favor the formation of secondary aerosols via providing reaction sites and reaction catalysts, as well as supplying soot, organic, mineral and metal particles in the size range of the accumulation mode. In addition, the contents of Ca, P, and Zn in organic particles may serve as fingerprints for source apportionment of particles from PFI-engine vehicles.     

某水利枢纽工程泄洪排砂洞进口边坡稳定性监测分析

边坡的失稳破坏,都有一个从渐变到突变的发展过程,在破坏前会显示出一些即将破坏的征兆。通过安装精密的仪器对坡体的变形进行监测,则可能捕捉到破坏前坡体稳定性的异常信息,可以及时发现问题和采取措施进行处理。坡体的位移是观测的最主要、最直观的物理量;用应力观测检验坡体的支护效果,与变形监测对照分析还可验证监测成果的可靠性。某水利枢纽工程通过埋设3支多点位移计和2支锚索测力计,对裂隙发育、坡面破碎的泄洪排砂洞边坡施工过程中的变形进行了监测分析,监测成果表明泄洪排砂洞进口边坡目前是稳定的。     

我国轻型汽车污染物排放因子的测试研究

采用底盘测功机按ＥＣＥ－１５规程测试了我国１３辆（１２种）正在使用的轻型汽车的ＣＯ、ＨＣ和ＮＯｘ的排放量分别为８７．２５±５６．３１、１１．３６±５．１３和８．２０±６．６８ｇ／ｔｅｓｔ;在相同测试条件下,测试了其中１１种轻型车在不同车速匀速行驶时的ＣＯ、ＨＣ和ＮＯｘ排放因子．测试结果表明、轻型汽车污染物排放因子随车速的变化有良好的规律性．用统计方法拟合了轻型汽车污染物排放因子的车速变化系数的计算公式。当车速＜９０ｋｍ／ｈ时,轻型车ＣＯ、ＨＣ排放因子随车速的增加而减小,当车速＞９０ｋｍ／ｈ时,又略有增加,而ＮＯｘ排放因子随车速的增加而增大。     

汽车环境风洞地面区域流场数值仿真

目的 探究汽车环境风洞地面区域流场规律,获取风洞边界层抽吸装置的最佳抽吸率和底盘测功机对风洞地面区域边界层厚度、风速、总压和静压的影响规律,并比较MRF法和旋转壁面法对底盘测功机转毂转动模拟的精度。方法 运用计算流体动力学方法对汽车环境风洞流场进行数值仿真计算。结果 边界层抽吸装置对应于喷口风速120 km/h时的最佳抽吸率为0.048。底盘测功机区域总压呈现下降趋势。相比于存在底盘测功机,汽车环境风洞无底盘测功机时,底盘测功机区域内相同位置的边界层厚度会增加1.28～12.22 mm。在前转毂的前侧、上侧、后侧和后转毂的上侧和后侧会有一个高风速区域,区域内风速比设定风速高1%～4%,与无底盘测功机相比,区域内静压值低0.32～46.02 Pa。在前后转毂前侧和后侧与地面相连接的凹部会有一个低风速区域,区域内风速比设定风速低1%～5%,与无底盘测功机相比,区域内静压值高0.08～49.34 Pa。底盘测功机转毂的转动会使附近区域的地面边界层厚度变大。在前转毂前侧,采用旋转壁面法进行模拟比MRF法地面边界层厚度增加近8 mm,而在其他位置,2种模拟方法对边界层厚度的模拟差别在1.5 mm...     

不同类型机动车尾气中的多环芳烃含量分析

采用底盘测功机模拟汽车的加速、减速、匀速和怠速过程,采集了机动车排放的尾气,并对尾气中颗粒态物质和气态物质的多环芳烃含量进行了分析,结果表明,柴油车和汽油车无论在何种工况下,尾气中低环多环芳烃在气态物质中的含量都要高于在颗粒态物质中的含量;中环多环芳烃在气态物质中和颗粒态物质中的含量相接近;高环多环芳烃在颗粒态物质中的含量要高于气态物质中的含量.机动车尾气中PAHs的苯并[a]芘等效致癌浓度(BaPE)在0.558～5,684之间,BaPE/BaP比值在2.029～8.413之间.即BaP以外的多环芳烃贡献了相当于103%～741%BaP浓度的等效致癌毒性;尾气中气态物质和颗粒态物质的PAHs总量和苯并[a]芘含量的回归分析表明两者之间存在着较好的线性关系,其可决系数分别为0.8343和0.7158.     

机动车尾气碳质气溶胶排放因子及其稳定碳同位素特征

机动车尾气是大气碳质气溶胶的重要人为来源,其排放因子与稳定碳同位素组成是重要的基础数据.选取多辆不同类型在用机动车,进行多种工况、冷/热条件下启动的台架试验,收集各测试阶段尾气分析其碳质组分含量与稳定碳同位素比值,并探讨其影响因素.结果表明,总碳排放因子大小为：重型柴油车>轻型柴油车>轻型汽油车,轻型天然气车虽然在低速与中速阶段排放因子极低,但高速行驶阶段可达到重型柴油车的排放水平.各型车冷启动的排放因子均高于热启动,NEDC工况的排放因子整体低于WLTC工况,应与其测试车速有关.汽油车和天然气车各测试阶段排放有机碳(OC)均远高于元素碳(EC),柴油车OC与EC排放因子相近,各类车辆OC/EC都随测试车速的提高而上升.稳定碳同位素EC重于OC,同位素比值大小关系均呈现：汽油车<天然气车<轻型柴油车<重型柴油车,现有源解析的稳定碳同位素源谱较难反映汽油车与天然气车特征.在排放治理与源解析工作中,应注意替代燃料的使用与机动车老化过程所造成的排放因子与同位素特征值的变化影响.     

不同燃料汽车排放超细微粒特性的实验研究

利用底盘测功机和粒径范围0.015~0.7 m的扫描迁移微粒测定仪 SMPS,对柴油出租车、柴油小巴车、汽油私家车和LPG出租车进行了高低怠速和10 kmh-1到70 kmh-1不同运行工况条件下排放的超细微粒粒径分布试验研究。研究表明：不同燃料车在不同工况条件下排放的细微粒尤其是超细微粒特征呈现显著的不同。柴油车贡献更多的是粒径在30～150 nm的核模态和积聚模态微粒,LPG和汽油车贡献更多的是15～30 nm的核模态微粒。总体上,柴油车比汽油车和LPG燃料车排放更多的微粒数和微粒质量;柴油车、汽油车和LPG车排放的SMPS可测细微粒总数、总质量分别约为(0.3~3.6) 108 cm-3,0.03~0.6 gcm-3;2.3×104~1.2×107 cm-3,8×10-5~0.1 gcm-3; 8.2×103~8.8×106 cm-3, 1.7×10-5~0.09 gcm-3;对所有测试汽车,在低怠速和低行驶速度时,排放微粒数少,在高怠速和高行驶速度时,排放微粒数多。     

轻型汽油车尾气OC和EC排放因子实测研究

选取27辆国3~国5轻型汽油车采用实验室底盘测功机和全流稀释定容采样系统(CVS)开展了尾气颗粒物中有机碳(OC)和无机碳(EC)组分的排放因子实测,分析了启动条件、行驶工况和喷油方式对轻型汽油车OC和EC排放的影响.结果表明,国3~国5轻型汽油车OC平均排放因子分别为(2.09±1.03)、(1.59±0.78)和(0.75±0.31)mg·km-1,EC平均排放因子分别为(1.98±1.42)、(1.57±1.80)和(0.65±0.49)mg·km-1,二者均随排放标准的提升呈显著下降趋势,OC/EC值分别为1.54±0.92、1.53±0.91以及1.47±0.66.OC1、OC2以及EC1和EC2是轻型汽油车排放的最主要碳质组分,分别占15.0%、20.6%、22.2%和21.7%.冷启动条件下轻型汽油车OC和EC排放约为热启动的1.4和1.8倍;高速工况下轻型汽油车OC和EC排放因子约为城区工况的2倍和4倍;缸内直喷(GDI)发动机的OC排放因子与进气道喷射(PFI)发动机接近,但EC排放因子约是后者的1.7倍,随着我国轻型汽油车中GDI发动机日渐普及,其EC排放应当引起密切关注.     

轻型汽油车VOCs排放特征和排放因子台架测试研究

为研究轻型汽油车尾气中VOCs的排放特征和排放因子,按照《轻型汽车污染物排放限值及测量方法》(中国Ⅲ、Ⅳ阶段)中要求,采用底盘测功机对国内现有不同品牌轻型汽车进行台架试验,并利用3级冷阱预浓缩GC-MS方法对尾气样品中VOCs物种进行定量分析.结果表明,尾气样品中共有68种VOCs被定量检出,其中芳香烃种类最多,占38.7%,烷烃占29.8%,烯烃(包含炔烃)占27.1%.不同品牌轻型车源排放谱特征基本吻合.轻型汽车的总VOCs排放因子为0.01~0.46g/km,前3位物种分别为乙烯、甲苯和苯.