基于Landsat 8遥感数据的天津市地表温度反演

以Landsat 8遥感数据为数据源,进行天津市地表温度反演研究。首先采用单通道算法反演地表温度,并利用均值标准差法进行温度分级。然后建立不同温度等级面积比例的估算模型。再通过随机样点,从不同温度等级和土地覆盖类型2个角度,分别建立并比较不同类样点的地表温度与各指数的拟合模型。结果表明:次高温区域面积比例与人口密度、人均GDP都具有较高的决定系数;地表温度与NDVI、BAEM的二元线性回归决定系数高于地表温度与单一指数的决定系数;将样点分类后,低温点与MNDBI的决定系数高于其他温度等级样点,水域和植被样点与各种指数的决定系数高于其他地物类型样点。     

Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9％ ～5.4％.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3％的系统脱硫效率整体高于含湿量为5％和4％的样品,最大值达93.56％.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3％的循环脱硫灰较含湿量为5％的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5％样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaS03干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

Challenges for modelling and integrating environmental performances in concept design: the case of an automotive component lightweighting

The objective of this paper is to discuss the main barriers for modelling and integrating the environmental performances in the automotive concept design. Incorporating environmental assessment in the early design phase of a vehicle component is known as an important challenge that car makers need to face in order to develop more sustainable design solutions; in this regard, the Life Cycle Assessment is the most widespread methodology for the environmental assessment and comparison of alternatives. The present work illustrates the combination of such methodology with the traditional design procedure at two different levels of the component design phase, material choice and concept design. In particular, the potential benefits originated by a lightweight solution for the automotive component Throttle Body are evaluated by considering environmental and technical implications at the same level. The case study shows that a multi-disciplinary approach for design effectively allows the integration of the environmental issue in the company’s established procedures. However, interpretation of results is still a challenging aspect due to the inevitable contradicting elements which should not discourage to develop comprehensive sustainability assessment within the early design stage.     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

大型水利水电工程实施占用耕地补偿制度的思考

本文在分析长江三峡工程用地特点的基础上。对大型水利水电工程实施耕地补偿制度中的问题和困难进行调查研究，认为应从新的视角来认识大型水利水电工程的耕地占补平衡问题。进而探索耕地补偿制度实施的新途径和新方式。应在耕地总量动态平衡政策适当调整的基础上．将“以地补地”和“缴费补地”的方式相结合。既通过土地整理．在提商土地质量的前提下增加耕地的有效面积：又要落实耕地开垦费．扶持库区的土地整理。从而使库区的耕地占补制度顺利实施。     

Study on the Balance of Agricultural Water and Land Resources on Ningxia Plain

The article puts forward the process and means of regional water and land balance research, and then from two scenarios which are the balances under natural regulation and human intervention, calculated and analysed the balance between water and land on Ningxia Plain. For the balance under natural regulation named farmland water balance, using farmland water resource balance equation, the research estimated the monthly farmland＂ water balance of 8 major crops for all of the 12 counties on Ningxia Plain in the period of 1960-2001; for the balance under human intervention, the research estimated land-use water balance equation of the counties in 2000, and calculated the balance between land use and water resources including irrigating water of all the 12 counties on Ningxia Plain. Results showed that ①precipitation can not meet the water demand of the crops for growth and development on Ningxia Plain, and water shortage is the primary character of farmland water balance under natural regulation. ②the diversity of water and land balance of different counties is distinctly influenced by the crop structure, water quantity for irrigation and irrigation level. ③Irrigation water could meet the crop water demand on Ningxia Plain in 2000, but there was not much space to expand irrigating cultivated land.     

区域水战略方案选优的动态组合评价模型研究

水安全危机是人类进入新世纪以来在生存及发展方面所面临的最严重挑战之一。研究科学合理的水安全战略成为区域可持续发展的重大课题。针对区域水战略问题涉及众多因素且各因素之间动态关联的特点，提出了基于水战略方案优选的兼容度极大化动态组合评价模型（CMM—DCEM），并将其成功地应用于我国广东省北江下游及其三角洲地区水安全战略方案优选评价。评价结果及模型基于不确定性的敏感性分析结果证明：CMM—DCEM实现了主、客观赋权方法以及单一评价模型的融合，使用实码加速遗传算法求解目标函数，克服了传统的组合评价方法计算繁琐的不足，评价过程更加科学合理。     

基于LOADEST和数字滤波的水源地基流氮素输出定量方法应用实例

地表直接径流和基流均是流域非点源氮/磷养分输出的重要水文途径.科学认识和定量模拟基流氮/磷养分输出对于准确解析水源地水体非点源污染来源至关重要.基于Load Estimator模型和数字滤波算法,建立了定量水源地基流氮素输出的方法体系.以浙江省珊溪水源地的玉泉溪流域为例,利用玉泉溪2010-01—2013-12期间逐月总氮(TN)水质监测数据和逐日流量数据,展示了该方法的计算过程.结果表明,本文建立的水源地基流氮素输出定量方法结果合理,模拟精度高,决定系数和纳什系数分别为0.83和0.80;玉泉溪流域2010—2013年TN负荷量为141.21～274.68 t·a~(-1),平均208.63 t·a~(-1),年基流TN负荷量为84.39～168.68 t·a~(-1),平均127.69 t·a~(-1);基流对玉泉溪年均TN负荷量贡献率高达60%以上,流域基流养分输出对地表水体的污染应引起足够重视.     

基于改进遗传算法的河流水污染源反演方法

针对河流水污染应急响应过程中污染源排放历史迟知、未知的问题,结合多种群遗传算法和自适应遗传算法,利用一维河流水质模型和水质监测数据,研究建立了基于改进遗传算法的河流水污染定量源反演方法,实现了对河流污染源排放历史的识别与重构.将该方法应用于美国特拉基河流的3个不同流量下的示踪剂实验中,对示踪剂排放历史进行定量源反演分析.结果表明：IGA算法对高、中、低不同流量下的3次示踪剂实验均可以很好的重构和识别示踪剂排放历史,对于实际河流水污染源反演分析的误差均在可接受范围内.IGA算法在河流水污染源反演分析中具有一定的可靠性和稳定性,可为河流水污染精准溯源与治理提供科学的技术支撑.