废旧硬质聚氨酯泡沫塑料的木质素改性及再生

采用含有二乙二醇(DEG)和乙醇胺(ETA)的双组分解交联剂降解废旧硬质聚氨酯泡沫塑料(PU硬泡),并利用降解得到的低聚物多元醇与木质素复合制备出性能增强的再生PU硬泡。通过对制备的再生PU硬泡的红外光谱、密度、吸水率、抗压强度、热稳定性、导热系数、热重曲线等进行分析测试,考察m(DEG)∶m(ETA)对再生PU硬泡性能的影响。实验结果表明:m(DEG)∶m(ETA)=1∶3时废旧PU硬泡的降解效果最好;木质素加入量为2.0%(w)时再生PU硬泡的密度低、抗压强度高、保温性能良好,达到国家标准《建筑绝热用硬质聚氨酯泡沫塑料》(GB/T 21558—2008)的品质要求。     

磁性生物膜载体的规模化制备、表征和应用

利用机械力化学表面改性原理设计了卧式双旋搅拌混合反应设备,通过磁铁矿粉和适量浓硫酸的球磨混合反应制备得到磁性生物膜载体,其XRD、IR、SEM和BET表征分析结果表明,磁性生物膜载体表层生成了多羟基硫酸铁为主的活性组分.进而在膜生物反应器实验装置中投加磁性生物膜载体进行了中试实验,结果表明,磁性生物膜载体能与活性污泥中的微生物聚合形成稳定的菌胶团,活性污泥SV30从实验初期89％降到了稳定期的39％,此外,磁性生物膜载体还具有稳定膜生物反应池出水COD,强化脱氮除磷的能力.     

大孔网状聚氨酯载体MBBR工艺处理低浓度硝基苯废水实验研究

利用大孔网状聚氨酯载体在MBBR工艺条件下,研究了系统挂膜与启动过程,同时利用挂膜成熟稳定的载体进行低浓度硝基苯废水处理实验。研究结果表明,在20℃条件下培养的活性污泥生长状况良好,挂膜速度快,生物膜厚度大,耐冲击负荷。在MBBR反应时间24 h、材料投加量为1/4、硝基苯初始浓度为2.095mg/L的条件下,处理低浓度硝基苯废水的效果最好,CODcr去除率为92.58%,硝基苯去除率为49.82%。     

硬质聚氨酯泡沫和组合聚醚中消耗臭氧层物质的便携式GC-MS测定方法

建立了便携式顶空/气相色谱-质谱法测定硬质聚氨酯泡沫和组合聚醚中一氟三氯甲烷（CFC-11）、二氟二氯甲烷（CFC-12）、二氟一氯甲烷（HCFC-22）及一氟二氯乙烷（HCFC-141b）的定性分析方法，系统考察了色谱柱、顶空体系、顶空温度和顶空时间对测定结果的影响。结果表明，DB-WAX色谱柱对目标物质的分离效果最好，顶空温度为50℃、顶空时间为10 min条件下，目标物质的检测灵敏度最高。在优化条件下，硬质聚氨酯泡沫取样体积为1 cm³时，4种目标物的方法检出限为0.6~0.8 μg；组合聚醚取样量为10 mg时，4种目标物的方法检出限为0.5~0.6 μg。该方法具有较高的灵敏度，定性准确，适用于实际样品的现场快速定性分析。     

以聚己内酯作为生物反硝化固体碳源的研究

为解决水体因低碳氮比而导致脱氮效率差的问题,将颗粒聚己内酯(PCL)重新塑形为阶梯环状,研究其作为反硝化过程的生物膜载体与固相碳源的反硝化性能。结果表明,在静态实验中,平均反硝化速率为8.57 mg NO3-N/(L·h);反硝化过程为零级反应。连续填充床实验中,超过90%的硝酸盐可被去除,出水NO2-N质量浓度低于0.20 mg/L;出水NH3-N质量浓度略有上升;出水溶解性有机碳(DOC)先上升后降低至1 mg/L左右。电子扫描显微镜扫描显示,PCL阶梯环反应表面空隙率较高,表面生物膜以杆菌为主,反应后被明显腐蚀;液相色谱检测显示PCL阶梯环分子量反应前后略有下降,其结构未受到破坏;表明该材料适合作为反硝化反应的碳源的同时,又可以作为载体供微生物附着生长。     

污水处理移动床生物膜反应器悬浮载体研究进展

介绍了移动床生物膜反应器(MBBR)中悬浮载体的种类和特性,讨论了对其性能的影响因素,总结了当前悬浮载体改性技术及性能评价的方法,并对后续研究提出了建议。     

废旧冰箱拆解聚氨酯泡沫塑料制备PU/PP复合材料

利用废旧冰箱拆解的聚氨酯泡沫塑料(PU)和聚丙烯(PP)、聚丙烯接枝马来酸酐(PP-g-MAH)为原料,采用物理化学回收技术制备PU/PP复合材料。用正交实验法分析PU填充量、PU粒径和PP-g-MAH 3个因素对PU/PP复合材料力学性能影响的显著性。结果表明,PU填充量对PU/PP复合材料拉伸性能有显著影响,对冲击性能和弯曲性能没有显著影响;在本文的实验范围内,PU粒径对PU/PP复合材料的力学性能影响不大;而PP-g-MAH投加量对PU/PP复合材料具有一定的影响。确定的优化工艺配方为:PU 40%;PU粒径选择2.00 mm;PP-g-MAH投加量10%。采用优化工艺制备的PU/PP复合材料的密度为1 042.88 kg/m3;冲击强度为2.9 kJ/m2;拉伸强度为10.30 MPa;拉伸模量为1 100 MPa;弯曲强度为18.5 MPa;弯曲模量为733 MPa。     

Highlights of LNG risk technology

The authors have recently undertaken a major review of LNG consequence modeling, compiling a wide range of historical information with more recent experiments and modeling approaches in a book entitled “LNG Risk-Based Safety: Modeling and Consequence Analysis”. All the main consequence routes were reviewed – discharge, evaporation, pool and jet fire, vapor cloud explosions, rollover, and Rapid Phase Transitions (RPT’s). In the book, experimental data bases are assembled for tests on pool spread and evaporation, burn rates, dispersion, fire and radiation and effects on personnel and structures. The current paper presents selected highlights of interest: lessons learned from historical development and experience, comparison of predictions by various models, varying mechanisms for LNG spread of water, a modeling protocol to enable acceptance of newer models, and unresolved technical issues such as cascading failures, fire engulfment of a carrier, the circumstances for a possible LNG BLEVE, and accelerated evaporation by LNG penetration into water.     

Optimization of the recovery of plastics for recycling by density media separation cyclones

Material recovery processes are presented as the optimum option for recycling plastic wastes as a means of recovering hydrocarbon resources. There exist a large variety of automated material recovery processes for recycling of such wastes but each with significant limitations. Of these, the separation based on differences in densities is advocated as the optimum process either for producing recycled products or preparing wastes for subsequent recovery processing.Density separation processes based on cyclone type density media separation (DMS) is presented as an important, potential method for increasing plastics recycling process capacities. It is demonstrated to have the capacity to separate a significantly larger range of particle sizes than those presently processed industrially. The mathematical relationship for the prediction of quality of typical LARCODEMS type density media separations by particle size and density as expressed by the Ecart Probable is presented.A proposed device configuration is presented for density media separation to optimize the recovery and purity of both density fractions produced. It is also suggested that to be economically viable, a large scale of operation is required for industrial plastics recycling operations recovering and producing a number of different plastics with a purity to be used as a substitute for virgin material.     

石化废水深度处理用臭氧催化氧化体系的研究＊

文章就臭氧催化氧化体系在石化废水处理中的作用进行了深入研究,对催化剂载体、催化剂配伍体系以及臭氧的投加方式进行了优化筛选。根据实验,多元催化掺杂体系较一元催化体系氧化效果好,CODCr的去除率可由一元催化时的20%提高到多元催化时的33%;在臭氧的投加方式上,分段投加要优于单级投加,臭氧投加分配比例为6∶3∶1时,CODCr的去除率可由单一投加时的9%提高到分级投加时的19%。