臭氧氧化处理页岩气钻井废水的机理与动力学

采用臭氧氧化法处理页岩气钻井废水经混凝沉淀后的出水(COD=759.63 mg/L),重点研究了废水中有机污染物的去除机理与反应动力学。实验结果表明:在废水pH为11.2、臭氧通入量为8 mg/min、反应时间为50 min的最佳工艺条件下,废水的COD去除率为42.51%;羟基自由基抑制剂CO_3~(2-)、HCO_3~-和叔丁醇的引入抑制了废水COD的臭氧氧化去除,尤其是叔丁醇的加入使COD去除率显著下降,说明废水中有机物的臭氧氧化去除过程遵循羟基自由基机理;臭氧氧化法对钻井废水中有机物的氧化去除过程符合表观二级反应动力学规律。     

基于疲劳累积破坏机制的储罐结构动力可靠度分析

针对随机风载荷作用下储罐结构动力可靠性问题，以300 m3的中小型立式低温储罐为研究对象，利用AR模型进行数值模拟得到风载荷的脉动风速时程与脉动功率谱密度函数。采用ANSYS建立储罐三维有限元模型，并对储罐进行动力学分析，计算出储罐结构的随机响应，进而求出随机风载荷作用下储罐结构动力可靠性所需全部数字特征，最后利用疲劳累积损伤机制计算得到储罐的动力可靠度。结果表明:假设结构强度不随时间退化，前5 a动力可靠度基本保持不变，随着使用年限的延长，动力可靠度下降速度明显增大。研究方法可为储罐的动力可靠性及寿命预测提供一定的理论依据。     

脱硝催化剂的失活机理及其再生技术

采用SEM、XRD和XRF对电厂失活脱硝催化剂进行表征,探讨其失活原因和机理。结果表明:电厂脱硝催化剂失活的主要原因是活性组分V的流失及碱金属K、碱土金属Ca和As元素造成的催化剂中毒,烟气中飞灰的沉积也有一定的影响。经吹扫、水洗、酸洗和V负载再生,催化剂的各项物化性质基本恢复,NOx转化率基本达到新鲜催化剂的水平。水洗主要去除催化剂中的碱金属,酸洗主要去除As2O3,负载V补充催化剂活性组分。V再生催化剂在较高温度下的抗硫性能更好。     

A Bayesian network-based approach for the assessment and management of ageing in major hazard establishments

Currently, there is an increasing attention towards ageing of industrial equipment, as the phenomenon has been recognised as a cause of severe accidents, recorded in the last years in many process establishments. Recent studies described ageing through a number of key-factors affecting the phenomenon by accelerating or slowing it down. The Italian Competent Authority for the prevention of chemical accidents (Seveso III Directive) adopted a short-cut method, accounting for the assessment of these factors, to evaluate the adequateness of ageing management during inspections at Seveso sites. In this paper, a Bayesian Network was developed, by using the data gathered during the first application of the short-cut method, with the aim to verify the robustness of the approach for ageing assessment and the validity of the a priori assumptions used in assessing the key-factors. The structure of the Bayesian network was established by using experts’ knowledge, whereas the Counting Learning algorithm was adopted to execute the parameter learning by means of the software Netica. The results showed that this network could effectively explore the complex logical and uncertain relationships amongst factors affecting equipment ageing. Results of the present study were exploited to improve the short-cut method.     

Research based on double coverage rate and reliability of gas detector layout optimization

The gas detector layout should be highly attuned to combustible gas leakage and attain a good reliability in avoiding detector malfunction, which is an important guarantee for the normal production of the chemical industry and other related enterprises. Herein, a gas detector layout optimization method based on double coverage and reliability is proposed. The key gas leakage monitoring area is determined through layout scene field investigation. To improve the detection probability and detection system reliability, the dual coverage target and voting mechanism are set, and the gas detector layout is determined with the ray-casting algorithm according to the coverage target. Combined with FLACS software to simulate a variety of typical leakage conditions under different layout scenarios, the relationship between the leaked gas concentration detected by gas detectors in each layout scheme and time is obtained, and the gas leakage detection probability in each layout scheme, number of detectors that can trigger the alarm, shortest time to trigger the alarm and reliability are comprehensively evaluated. The decision-maker selects the final gas detector layout plan according to the evaluation results and actual site needs. The study shows that the detection probability of each layout scheme set according to the double coverage is high, and multiple detectors can trigger the alarm (up to 100%), which ensures that the alarm can be triggered within 10 s under all applicable conditions. According to the evaluation results, the decision-maker can obtain a layout scheme that not only agrees with the actual site conditions but also attains a high detection probability, short detection time and strong reliability.     

过一硫酸盐的活化及其降解水中有机污染物机理的研究进展

基于活化过一硫酸盐（PMS）产生SO₄^-·的新型高级氧化技术,在芬顿和类芬顿催化降解水中有机污染物的研究中占有重要地位。本文从活化PMS方法的特点和用途出发,对目前活化PMS的主要方法进行了论述,并对活化PMS降解水中有机污染物的机理进行了探讨,最后对该领域研究中存在的问题进行了分析。指出,开发高效的协同活化PMS的方法将成为该领域研究的必然趋势。     

A product analysis-based study on the mechanism of inflammable gas explosion suppression

To study the mechanism of the suppressing effect of Expanded Aluminium (EA) on the premixed gas explosion, premixed methane-air and propane-air gases were undergone explosion reaction in the presence of EA in a self-designed closed pipeline with the overpressures and the compositions, rates and sensitivities of products analyzed. The results showed that the 9.5% methane-air and 5% propane-air explosions produced peak pressures decreased by 79.3% and 65.6%, and residual methane and propane contents increased by 270% and 560% respectively than without EA. In addition, the results revealed that the explosions of propane in the presence of EA produced less methane and carbon oxides contents, but more ethylene and propylene contents. The simulation showed that H, O, and OH are the key factors affecting the rate of products. The product compositions, together with other parameters, suggested that EA decreased temperature, inhibited chain initiation and propagation reaction, but facilitated chain termination reaction by advancing and accelerating the gas phase and wall destruction reaction of radicals, especially collisions and concentration of key free radicals. This new research method based on the analysis of explosion products can be used for in-depth research into gas explosion features and shed light on the suppressing mechanism of EA in flammable gas explosion.     

Behavioral pathways in bicycle-motor vehicle crashes: From contributing factors,pre-crash actions,to injury severities

Introduction: This study performed a path analysis to uncover the behavioral pathways (from contributing factors, pre-crash actions to injury severities) in bicycle-motor vehicle crashes. Method: The analysis investigated more than 7,000 bicycle-motor vehicle crashes in North Carolina between 2007 and 2014. Pre-crash actions discussed in this study are actions of cyclists and motorists prior to the event of a crash, including “bicyclist failed to yield,” “motorist failed to yield,” “bicyclist overtaking motorist,” and “motorist overtaking bicyclist.” Results: Model results show significant correlates of pre-crash actions and bicyclist injury severity. For example, young bicyclists (18 years old or younger) are 23.5% more likely to fail to yield to motor traffic prior to the event of a crash than elder bicyclists. The “bicyclist failed to yield” action is associated with increased bicyclist injury severity than other actions, as this behavior is associated with an increase of 5.88 percentage points in probability of a bicyclist being at least evidently injured. The path analysis can highlight contributing factors related to risky pre-crash actions that lead to severe injuries. For example, bicyclists traveling on regular vehicle travel lanes are found to be more likely to involve the “bicyclist failed to yield” action, which resulted in a total 44.38% (7.04% direct effect + 37.34% indirect effect) higher likelihood of evident or severe injuries. The path analysis can also identify factors (e.g., intersection) that are not directly but indirectly correlated with injury severity through pre-crash actions. Practical Applications: This study offers a methodological framework to quantify the behavioral pathways in bicycle-motor vehicle crashes. The findings are useful for cycling safety improvements from the perspective of bicyclist behavior, such as the educational program for cyclists.     

Assessment of the effect of technical and management characteristics on the frequency of release from piping: An application to a gas storage facility

The assessment of the frequencies of release from piping due to losses of containment is an essential step in the preparing Safety Reports, drawn up as required by the so-called “Seveso” Directive. These are usually calculated starting from the frequencies of random rupture included in international databases and are not plant-specific, furthermore, the quantification of the effect of the safety management system of the facility is not easy. A simple and flexible approach quantifying technical and management characteristics of the plant has been proposed by Milazzo and co-workers in 2010; it is based on the modification of the frequency taken from literature, through the use of the percentages of failure causes actually possible in that plant, and the judgment about their management. The data about the failure causes are taken from the literature and modified by using corrective factors to adapt them to the industrial context. To make possible the application of the method to a large number of major-hazard industry types, some aspects of the approach needed to be improved; these have been identified during a development project coordinated by RINA Consulting, on behalf of Saipem, with the collaboration of the University of Messina. The improvement of the approach focused on two main points, the development of a method to calculate the corrective factors for the failure causes associated with corrosion and erosion phenomena and the strengthening of the methodology for the formulation of the judgment about the safety management. This paper illustrates the fully improved method, as well as an application to a typical gas storage plant.     

面向突发事件智能建筑管理系统的集成结构

为了实现面向突发事件的智能建筑管理系统(IBMS),提出了智能建筑突发事件的抽象模型、基本运算操作及优先权分配机制,并根据突发事件监控和管理的目标,提出了IBMS的"分布式虚拟应急中心"集成结构.