Preparation and performance of novel APP/NaY–Fe suppressant for coal dust explosion

Coal dust explosion occurs easily in the coal chemical industry. To ensure safety in industrial production, NaY zeolite was used as carrier modified with Fe ions and combined with ammonium polyphosphate (APP) to prepare a novel composite suppressant for coal dust explosion. The explosion suppression performance of novel APP/NaY–Fe suppressant was investigated by flame propagation inhibition experiments. The results show that Fe ion modification can effectively improve the explosion suppression performance. By increasing content, the explosion suppression performance of the explosion suppressant increases. The maximum explosion pressure P_max of coal dust drops to 0.13 MPa when 50 wt% explosion suppressants were added, and the coal dust explosion cannot continue to expand. Complete suppression of explosion could be achieved by adding 66 wt% explosion suppressants. Combined with XRD, SEM and TG results, the explosion suppression mechanism was proposed. The novel explosion suppressant has high thermal stability, good dispersity and its explosion suppression components distribute uniformly. It shows good explosion suppression performance by the synergistic effect among explosion-suppression components.     

β-环糊精接枝羧甲基壳聚糖吸附剂的制备及其性能

采用γ-氨丙基三乙氧基硅烷化学修饰活化后的硅胶,以戊二醛为交联剂,接上羧甲基壳聚糖,继而接枝上β-环糊精作为功能单体,制备了一种用于分离富集水样中Cu(Ⅱ)的固相萃取新材料。利用红外光谱(FT-IR)、比表面分析(BET)、X射线衍射光谱(XRD)以及热重分析(TG)等方法对吸附剂进行结构表征。采用火焰原子吸收(FAAS)作为检测手段,考察了溶液p H、振荡时间、吸附剂用量、样品流速、洗脱液浓度和体积等对吸附剂吸附Cu(Ⅱ)的影响。吸附剂饱和吸附容量为9.37 mg/g,最大富集倍数高达350。吸附过程能用准二级动力学模型和Langmuir等温吸附方程进行很好的拟合。应用于环境水样中Cu(Ⅱ)的分离富集与测定,回收率在96.8%~105.2%之间,效果较好。     

某矿低铜废石综合回收利用项目职业病危害预评价

为了对某矿业有限公司低铜废石综合回收利用项目可能产生的职业病危害因素进行辨识、分析和评价，采用检查表、类比法相结合的原则对该项目的铲装、破碎、运输、筑堆等工艺进行分析评价，并利用经验法对浸出、萃取电积工艺进行分析评价。结果表明:类比工程中绝大部分粉尘、噪声检测点的浓（强）度符合国家标准；化学毒物、工频电场接触浓（强）度符合国家标准；电积车间的通风满足要求；萃取车间的事故通风能力不足。评价方法及通风计算方法对同类项目具有借鉴意义。     

单芯铜线过电流故障电弧熔痕的微观特征研究*

为准确认定电气火灾中过电流故障，模拟4~7倍额定电流（Ie）条件下单芯铜导线过电流故障，利用光学显微镜和扫描电子显微镜（SEM）分析过电流故障电弧熔痕的组织特征，并结合Image-Pro Plus软件测定晶粒直径、周长和面积，探究金相组织的量化判据和变化规律。结果表明:当I＝4Ie时，过电流故障电弧熔痕的金相组织主要为方向性较强的树枝晶；当I＝5Ie，6Ie时，金相组织内树枝晶占比减小，胞状晶占比升高；当I＝7Ie时，方向性较弱的胞状晶占主导。随着电流增加，晶粒的平均直径、周长和面积均呈增长趋势。通过火灾案例分析可知，实验结果与现场的电弧熔痕组织特征基本相符，验证火灾事故原因为过电流故障。     

白银天然沸石对磷的吸附机理及性能研究

为探明天然沸石对磷的吸附机理,首先利用扫描电镜、X射线衍射、X荧光分析等对甘肃白银产天然沸石进行了表征,然后通过静态实验探讨了吸附时间、磷初始浓度、pH值等因素对沸石除磷性能的影响.研究结果表明：沸石对水溶液中磷的吸附动力学过程符合Pseudo second-order模型;Freudlich和Langmuir模型均可较好地描述沸石对磷的吸附特征;沸石对磷的吸附量随pH值增大而明显减小.     

四环素类抗生素和铜复合污染对猪粪厌氧消化的影响

兽用抗生素和矿物元素添加剂可起到预防动物疾病、促进动物生长、提高饲料转化率等作用,因此被广泛应用于畜禽养殖业。本研究以猪粪中温厌氧消化为研究目标,采用全自动甲烷潜势测试系统,考察了一定浓度的四环素(TC:30 mg·kg~(-1)dry weight,DW)、土霉素(OTC:50 mg·kg~(-1)DW)和金霉素(CTC:15 mg·kg~(-1)DW)对厌氧累积产甲烷量和日产甲烷速率的影响。结果表明,TC、OTC和CTC对猪粪中温厌氧消化累积产甲烷量和日产甲烷速率均有促进作用(累积产甲烷总量提高比例分别为7.9%、0.4%和5.4%)。另外,采用超高效液相色谱-四极杆串联质谱对猪粪厌氧消化前后样品中四环素类抗生素及其代谢产物进行了分析。结果表明,液相中的四环素类抗生素在猪粪厌氧消化过程中得到了明显的去除,去除率达到90%~100%;而固相中只有金霉素和差向异构金霉素有明显的去除效果,去除率分别为41.69%和41.58%。采用Tessier连续提取法对猪粪厌氧消化前后样品中5种形态的铜包括可交换态、碳酸盐结合态、铁锰氧化结合态、有机物结合态、残渣态进行了分析,结果表明,猪粪厌氧消化后,可交换态、碳酸盐结合态和铁锰结合态的铜浓度比厌氧消化前分别降低了1%~9%、0.1%~3%、12%~19%,而有机态和残渣态的铜浓度却在厌氧消化后分别增加了15%~35%、1%~2%。厌氧消化后,70%~80%的铜都是以有机铜的形态存在。铜逐渐从不稳定态转化为相对稳定的有机态和残渣态铜,因此,厌氧消化过程使铜从可生物利用态转变为不可生物利用态,趋于稳定化。     

铜-磺胺嘧啶复合胁迫对蔬菜种子发芽的急性毒性效应

研究了黄潮土中常用兽药磺胺嘧啶(SD)与重金属铜(Cu)单一及复合污染对小白菜和西红柿种子发芽(发芽率、根伸长、芽伸长)的影响,分析了土壤中药物浓度与作物生长抑制的剂量-效应关系及复合污染的毒性效应。结果表明,无论是在Cu或SD单一污染物作用下,根伸长和芽伸长抑制率与污染物浓度显著相关(P0.01),发芽抑制率与污染物浓度不相关(P0.05);污染物对根伸长及芽伸长的抑制高于对种子发芽的抑制;SD对2种作物的毒性效应明显强于Cu,SD对小白菜和西红柿根伸长的ID50(抑制率为50%时污染物浓度)分别为1.7和33.6 mg·kg~(-1),而Cu为273.6和457.7 mg·kg~(-1)。Cu-SD复合污染,对西红柿的根和芽伸长的拮抗作用显著(P0.01);但对小白菜来说,在低浓度Cu(100 mg·kg~(-1))作用下,二者的联合拮抗作用不显著(P0.05),随Cu的增加,拮抗作用显著(P0.01)。     

氧化石墨烯对亚甲基蓝和铜离子的共吸附行为研究

氧化石墨烯(GO)具有高比表面积和丰富的含氧官能团,表面存在着大量的吸附点位,被认为是去除水体污染物的高效吸附剂,而其在有机物-重金属复合污染环境中的吸附行为却鲜有报道.因此,本文采用改良Hummers法制备出GO,通过扫描电镜(SEM)、透射电镜(TEM)、红外光谱(FTIR)、拉曼光谱(Raman)和X射线衍射(XRD)等物理表征方法对GO的形貌结构和表面官能团进行了表征.随后,侧重研究了GO对有机物及重金属污染物的单独和共吸附行为,选取亚甲基蓝(MB)与Cu(Ⅱ)作为复合污染水体的特征污染物,探讨了不同浓度Cu(Ⅱ)对MB及不同浓度MB对Cu(Ⅱ)的吸附性能的影响.结果表明,不同类型的污染物单独存在时,GO对MB和Cu(Ⅱ)的吸附量分别为29.13和424.16mg·g-1;而当上述两种污染物共存时,GO对MB和Cu(Ⅱ)的吸附性能均明显下降,这说明MB与Cu(Ⅱ)在GO表面的吸附点位存在着竞争吸附关系,并且MB对Cu(Ⅱ)吸附的抑制作用明显高于Cu(Ⅱ)对MB吸附的影响.     

Phosphorus recovery from biogas fermentation liquid by Ca–Mg loaded biochar

Shortage in phosphorus (P) resources and P wastewater pollution is considered as a serious problem worldwide. The application of modified biochar for P recovery from wastewater and reuse of recovered P as agricultural fertilizer is a preferred process. This work aims to develop a calcium and magnesium loaded biochar (Ca–Mg/biochar) application for P recovery from biogas fermentation liquid. The physico-chemical characterization, adsorption efficiency, adsorption selectivity, and postsorption availability of Ca-Mg/biochar were investigated. The synthesized Ca–Mg/biochar was rich in organic functional groups and in CaO and MgO nanoparticles. With the increase in synthesis temperature, the yield decreased, C content increased, H content decreased, N content remained the same basically, and BET surface area increased. The P adsorption of Ca–Mg/biochar could be accelerated by nano-CaO and nano-MgO particles and reached equilibrium after 360 min. The process was endothermic, spontaneous, and showed an increase in the disorder of the solid–liquid interface. Moreover, it could be fitted by the Freundlich model. The maximum P adsorption amounts were 294.22, 315.33, and 326.63 mg/g. The P adsorption selectivity of Ca–Mg/biochar could not be significantly influenced by the typical pH level of biogas fermentation liquid. The nano-CaO and nano-MgO particles of Ca–Mg/biochar could reduce the negative interaction effects of coexisting ions. The P releasing amounts of postsorption Ca–Mg/biochar were in the order of Ca–Mg/B600 > Ca–Mg/B450 > Ca–Mg/B300. Results revealed that postsorption Ca–Mg/biochar can continually release P and is more suitable for an acid environment.     

碱熔融—微波晶化法合成粉煤灰沸石及其对Cd2+的吸附

以粉煤灰为主要原料，采用碱熔融—微波晶化法合成粉煤灰沸石。采用XRD，SEM，TEM等技术表征了粉煤灰沸石的微观结构，并对其吸附Cd²⁺的性能进行了研究。表征结果显示，粉煤灰沸石主要由X型沸石、P型沸石和铝组成，粉煤灰沸石中有排列规则、呈蜂窝状的孔穴和孔道存在，其孔穴和孔道大小分布均匀，致密。粉煤灰沸石的比表面积为108.49 m²/g，平均孔径为3.779 nm，孔体积为0.221 mL/g。实验结果表明，在溶液pH为7、吸附时间30 min的最佳吸附条件下，Cd²⁺去除率均大于94%。粉煤灰沸石对Cd²⁺的吸附可很好地用二级动力学方程进行拟合，相关系数为0.999 99。可用Langmuir等温吸附模型描述该吸附过程，该吸附过程是单分子层吸附，主要是化学吸附，粉煤灰沸石对Cd²⁺的饱和吸附量为49.261 mg/g。