Study of the performance of a coolant mixed with an Al2O3/SiC nanomaterial in an engine radiator

One of the important components of a car to control the temperature of a car's engine is the radiator. To increase the heat absorption capacity of the coolant/fluid used in the radiator with minimum pumping power, innovative fluids called nanofluids have become the main area of research these days. Therefore, with the development of new technologies in the field of “nano-materials” and “nano-fluids,” the physical and chemical properties of coolant/fluid can be improved which in turn improves the radiator and engine efficiency, and reduces radiator weight and size. In this article, the heat transfer by forced convection in nanofluids based on Al₂O₃ and SiC was studied experimentally and compared to that of base fluid in an automotive radiator. The nanofluid is mixed with ethylene glycol and the fluid is prepared by the sonication method. The nanofluids were prepared by varying the nanomaterials and the amounts of nanomaterials in the base fluid and their heat transfer performance in the radiator was analyzed using ANSYS FLUENT software. Approximately 15% and 12% increase in radiator efficiency by using Al₂O₃ mixed nanofluid and SiC mixed nanofluid, respectively.     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9％ ～5.4％.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3％的系统脱硫效率整体高于含湿量为5％和4％的样品,最大值达93.56％.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3％的循环脱硫灰较含湿量为5％的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5％样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaS03干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

重点流域水系沉积物中多环芳烃标准样品制备

环境标准样品是监测过程中重要的质量控制手段,中国受天然基体标准样品制备技术的制约,尚未拥有自己的沉积物中多环芳烃标准样品。为制备符合中国重点流域沉积物类型及多环芳烃浓度水平的沉积物标准样品,对中国6个重点流域的沉积物进行了采样,获得了制备多环芳烃标准样品的原料。分析常温及冷冻2种干燥方式对多环芳烃的影响,为制备大批量多环芳烃标准样品提供数据支持。对11个点位样品采用气相色谱质谱法测定16种优控多环芳烃化合物浓度,结果表明,样品均匀性良好,样品中多环芳烃检出率在99%以上,江河沉积物样品中多环芳烃浓度区间为664~2.91×103μg/kg,湖泊样品最高值达到1.25×105μg/kg,其主要污染源是化学燃料的燃烧。为中国制备水系沉积物中多环芳烃标准样品积累了技术基础。     

Unintentional non-traffic injury and fatal events: Threats to children in and around vehicles

Objective: There have been substantial reductions in motor vehicle crash–related child fatalities due to advances in legislation, public safety campaigns, and engineering. Less is known about non-traffic injuries and fatalities to children in and around motor vehicles. The objective of this study was to describe the frequency of various non-traffic incidents, injuries, and fatalities to children using a unique surveillance system and database.

Methods: Instances of non-traffic injuries and fatalities in the United States to children 0–14 years were tracked from January 1990 to December 2014 using a compilation of sources including media reports, individual accounts from families of affected children, medical examiner reports, police reports, child death review teams, coroner reports, medical professionals, legal professionals, and other various modes of publication.

Results: Over the 25-year period, there were at least 11,759 events resulting in 3,396 deaths. The median age of the affected child was 3.7 years. The incident types included 3,115 children unattended in hot vehicles resulting in 729 deaths, 2,251 backovers resulting in 1,232 deaths, 1,439 frontovers resulting in 692 deaths, 777 vehicles knocked into motion resulting in 227 deaths, 415 underage drivers resulting in 203 deaths, 172 power window incidents resulting in 61 deaths, 134 falls resulting in 54 deaths, 79 fires resulting in 41 deaths, and 3,377 other incidents resulting in 157 deaths.

Conclusions: Non-traffic injuries and fatalities present an important threat to the safety and lives of very young children. Future efforts should consider complementary surveillance mechanisms to systematically and comprehensively capture all non-traffic incidents. Continued education, engineering modifications, advocacy, and legislation can help continue to prevent these incidents and must be incorporated in overall child vehicle safety initiatives.     

Heat dissipation characteristic in the intake grille and radiator of a fuel cell vehicle

ABSTRACT

In this study, a three-dimension (3D) computational model was proposed to investigate the flow and heat transfer characteristics of the intake grilles of two different fuel cell vehicles. The models of the intake grilles were constructed according to the actual sizes of two vehicles, namely, Roewe 950 and Toyota Mirai, considering the heat dissipation unit to simplify the heat transfer model of the vehicle. The results showed that relative to Roewe 950, Mirai intake air flow rate was approximately 10% higher, the heat transfer capacity was approximately 7% higher, and the intake grille area was larger. The coolant outlet temperature of Mirai was lower than that of Roewe 950, which was beneficial for the long term and stable operation of a fuel cell. This comparative study provided guidance for the intake grille and radiator design of fuel cell vehicles. The only difference between fuel cell vehicles on the market and conventional vehicles was that in the former, the internal combustion engine was replaced with a fuel cell stack, which had insufficient heat transfer capacity because of the reducing temperature difference. Increasing the intake grille area and the heat exchange capacity of the radiator were the key issues for the development of fuel cell vehicles. In this study, an optimal window opening angle of the radiator fin of 23° provided a maximal heat transfer coefficient.     

Characteristics of stable biodiesel emulsion fuel with the aid of lipophilic surfactant,polyglycerol polyricinoleate (PGPR)

ABSTRACT

Biodiesel emulsion fuel is reported as one of the most feasible options capable of generating lower NOx emission than that from fossil fuels. However, oil and water in the emulsion fuel are easily separated and unstable. The aim of the present study is to consider the production and stability of biodiesel emulsion fuel by using tetraglycerin ester (CR-310), i.e., one of lipophilic surfactant, polyglycerol polyricinoleate (PGPR) and biodiesel, i.e., Waste cooking Oil Methyl Ester (WOME) produced based on waste cooking oil. The corresponding heat rate, water content, and viscosity are measured. Emphasis is placed on the effects of water content and surfactant on biodiesel emulsions. It is found that: (i) stable emulsion fuel is obtained by adding at least 2.0% of CR-310 and is maintained over 1 month, (ii) there is no effect of water content on stable emulsion fuel if CR-310 is used over 2.0%, and (iii) the viscosity of emulsion fuels is higher than that of the biodiesel fuel and is gradually increased with an increase in the water content.     

示踪技术用于气体泄漏扩散模拟的多元线性回归分析

采用江苏工业学院油气储运安全综合实验模型平台,利用示踪技术(以CO2为示踪剂),模拟了有害气体瞬时泄漏扩散的整个过程.并结合多元线性回归分析的基本方法,定量分析了气体泄漏扩散过程,建立了多元线性回归模型,初步确定了泄漏气体浓度与相关物理量的变化关系,在此基础上得到了2个定量评价指标:确定性系数R=0.991,相关系数r=0.995.研究表明,在实验室建立的试验模型能较好地反映现实情况,模型仿真度较高,数据拟合效果较好.研究可为评价模型的相似性提供理论参考,对有害气体泄漏扩散事故应急救援、实施有效的现场控制,具有一定的科学参考价值.     

基于BP神经网络的矿车运行时矿井摩擦阻力的预测*

为了快速有效地确定矿车等运输设备在巷道内运行时矿井摩擦阻力的变化情况,克服模拟软件计算量和现场实测工作量大的问题,以巷道风流速度、矿车运行速度、阻塞比、矿车长度4个矿车运行时巷道摩擦阻力的影响因素作为切入点,采用动网格技术模拟得到矿车在巷道内运行时有关矿井摩擦阻力的数据,以此为样本构建基于BP神经网络的矿井摩擦阻力预测模型,运用MATLAB软件进行网络训练,并将BP神经网络预测值与FLUENT模拟值进行对比。研究结果表明:BP神经网络结构比较简单,能以较快速度收敛,预测值与模拟值最大误差在7%以内,该神经网络模型用于求解矿车等运输设备在巷道内运行时摩擦阻力的变化情况是可行的。     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

Improvement of welding heat source models for TIG-MIG hybrid welding process

Tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding process is an effective way to improve welding productivity and quality due to advantages of the two processes. Mathematical analysis is crucial to fundamentally understand this synergetic welding process. In this study, based on experimental visualization of arc behaviors, some assumptions are proposed to deduce adaptive plane and volumetric heat source models separately for each involved welding method first. The influence of torch angles on distribution of temperature and geometry of weld bead are calculated and compared with experimental results. It shows that this developed algorithm of heat source can be employed to accurately predict welding process whether the electrode gun is slanted backward or forward to the direction of welding. Then TIG-MIG hybrid welding process is simulated and analyzed without considering the attractive or repulsive force of two arcs. The characteristic of TIG-MIG welding process is discussed compared to single MIG. It lays the foundation for the further research on the interaction of the two arcs during TIG-MIG hybrid welding.