Impact of posture and upper-limb muscle activity on grip strength

Purpose. The current research was carried out to determine grip strength (GS) with change in posture and upper-limb muscle activity of manual workers and investigate the impacts of these changes. Methods. For the current research, 120 male and 80 female participants were selected and GS was assessed using a digital hand grip dynamometer in various conditions. Results. The outcomes showed that male participants had higher GS as compared to female participants. Maximum GS was found in a standing posture with the fixed forward shoulder at 45°, elbow at 90° and a neutral position of the wrist and forearm for all participants. Conclusions. Higher values of GS were attained in standing postures which may result in attainment of higher performance levels by the workers. The outcomes justify the importance of correct postures during manual work in industries employing traditional methods.     

基于力学机制的钢筋混凝土柱抗剪承载力模型∗

为了兼顾钢筋混凝土(RC)柱抗剪承载力分析的计算精度和简便性,研究建立了一种基于力学机制的RC柱抗剪承载力简化模型。首先基于变角桁架-拱模型理论,结合变角桁架模型的力平衡条件以及变角桁架模型和拱模型之间的变形协调条件,建立了RC柱抗剪承载力分析的理论模型;然后利用38组试验数据进行统计分析,分别确定了混凝土、箍筋和拱模型的抗剪承载力贡献系数近似取值,在此基础上建立了R C柱抗剪承载力分析的简化模型;最后通过与试验数据进行对比分析,验证了该模型的计算精度和适用性。分析结果表明,该模型不仅可以合理分析混凝土、箍筋和拱作用的抗剪承载力贡献,具有较高的计算精度,而且计算公式较为简洁。     

Strength and tightness evaluation method for pipe flange connections considering thermal effects

The pipe flange connection is widely applied in chemical, power plants, petrochemical, offshore oil and gas industries, and its strength and tightness are significant for the safe operation. However, there are still no practical and applicable strength and tightness evaluation methods for pipe flange connections working in dramatically varying temperatures. This paper proposed an approach to evaluate the pipeline's strength and sealing performance considering thermal effects in actual operating conditions by combining the experimental measurement and thermostructural analysis. The critical thermodynamic parameters are identified through measured temperature data in operating conditions, and then these parameters are used in the thermostructural analysis to obtain the actual temperature and stress fields. Then, the strength and tightness in complex temperature cases can be evaluated accurately. The pipe flange connection of a liquefied natural gas (LNG) fueling station is analyzed to verify the presented method's effectiveness. This method applies to evaluating the pipeline's strength and tightness and can predict the pipeline's performances under extreme temperatures using the tested data within the measurement range and the corresponding thermostructural analysis. Furthermore, the work in this paper also provides a reference for the design and analysis of pipe flange connections working in complex temperature conditions.     

冻融影响下不同岩性岩石物理力学特性试验研究*

为探究冻融循环影响下不同岩性岩石的物理力学性质的差异化响应,对青砂岩、灰砂岩2种砂岩,白色大理岩、麻粒岩2种变质岩开展冻融循环试验和相关力学试验。研究结果表明:在冻融循环过程中,2种砂岩的质量变化幅度明显高于2种变质岩。相较于青砂岩与麻粒岩,大理岩的单轴压缩强度及弹性模量劣化速率最快。冻融前后青砂岩、大理岩的单轴压缩破坏模式发生明显变化。灰砂岩抗拉强度劣化速率显著低于青砂岩。基于单轴抗压强度、抗拉强度的脆性指数表明冻融作用提高青砂岩的脆性。研究结果可为冻融影响下工程岩体的稳定性与安全性评价提供参考。     

不同离子对黑土胶体在土壤中运移的影响

黑土样品采自于黑龙江海伦市,提取胶体并对其主要理化性质进行定性定量表征,通过淋滤实验研究胶体在土柱中的运移特征以及不同离子及其强度对胶体运移的影响。结果显示:所提取胶体粒径与理论计算基本吻合,粒径主要分布在2~5μm;当pH由4上升到9时,胶体的zeta电位则由-26.43mV降低到-34.52mV;红外光谱显示胶体颗粒的有机机团主要为-OH、CH-、C=O、多糖;X射线衍射表明其主要矿物组成是石英(56.9%)。不同离子及其强度对胶体的在土壤中的运移有较为明显的影响,当pH由4增加到9时,k值由6.020×10-4降低至3.858×10-4,Ca2+、K+、Na+当离子强度由0.5mmol/L变化到0.001mmol/L时,k值分别由6.087×10-4降低至4.024×10-4、5.518×10-4降低至3.818×10-4、5.401×10-4降低至4.109×10-4。     

SRHSC梁主要设计参数损伤敏感度分析

以型钢高强混凝土(SRHSC)梁为研究对象,结合SRHSC梁受力机理及承载能力的试验研究成果,提出了极限状态下的承载能力是评价梁力学性能的关键指标,将损伤前后梁正截面抗弯承载力之比和斜截面抗剪承载力之比的均值作为自变量,给出了SRHSC梁损伤表征函数,并借助"预定损伤法",揭示了主要设计参数对SRHSC梁损伤演化的影响规律。研究成果将为建立地震激励下SRHSC框架结构楼层损伤模型提供理论和数据支持。     

离子液体对CO2吸收性能的研究进展

CO2引起的气候变暖已成为全球最关注的环境问题之一,利用离子液体固定CO2引起了众多学者的关注。介绍了近年来离子液体吸收CO2的研究进展,包括常规离子液体和含氨基离子液体、氨基酸离子液体、聚离子液体及其他离子液体等4种功能化离子液体,并简要分析了吸收机理。综合分析了每种离子液体的吸收性能,离子液体对CO2的吸收能力均随温度上升而减小,随压力升高而增加。烷基链的增长以及含氟基团的增加有利于对CO2的吸收。功能化离子液体由于引入了功能化基团,相同条件下,其对CO2的吸收力几乎是常规离子液体的两倍。此外,将离子液体与有机溶液(特别是醇胺溶液)混合能提高离子液体对CO2的吸收能力,且能降低生产费用。最后指出了高吸收性能、低黏度、低毒以及低成本是未来离子液体的研究方向。     

内排压脚与边坡稳定性的关系

为了研究边坡角及边坡形状与边坡稳定性的关系,采用有限元软件ANSYS模拟了不同边坡角对应的稳定系数,以及不同平盘宽度和压脚高度所形成的等储备强度边坡的稳定系数。模拟中假设材料符合相关联的理想弹塑性本构关系,强度准则符合Drucker-Prager准则,用计算收敛性作为边坡稳定性的准则,用强度折减法得出边坡的稳定系数。为了形成等储备强度边坡,由下到上分步骤进行压脚。先在平面边坡最下台阶压脚,这样提高了边坡稳定系数,在边坡进入临界状态时,最下两台阶的塑性状态相同,则压脚停止;再在最下两台阶同时压脚,在边坡进入临界状态时,最下3个台阶的塑性状态相同,则压脚停止;以此类推,在最下边n个台阶同时压脚,在边坡进入临界状态时,压到与第n+1个台阶的塑性状态相同为止。结果表明,边坡总是从坡脚开始形成塑性区,在重力加载过程中,塑性区以弧形条带向坡顶扩展,形成滑带。最有效的内排压脚是从最下台阶开始形成等储备强度边坡的压脚。     

含多弱层复合边坡滑坡治理三维数值分析

白音华二号矿滑坡区边坡治理工程是针对稳定性差的南帮非工作帮和南排土场构成的复合边坡进行的。滑坡体受多层弱层控制,治理过程中易导致边坡失稳,所以治理工程采取分区开采的条采方案,充分利用边坡治理的三维效应来进行边坡的失稳破坏研究和稳定性分析。选取滑坡区的典型剖面作为研究对象,基于强度折减方法(SRM),应用有限差分FLAC3D软件,在两种开挖条件下,对含多弱层的复合边坡的稳定性规律和破坏机制进行了数值模拟分析,揭示了多弱层对复合边坡的失稳破坏及稳定性的影响。研究结果表明,治理工程中,弱层被揭露一定宽度,滑体沿煤底板弱层水平错动、竖直方向拉裂破坏;随弱层暴露宽度的增加,边坡稳定性明显降低,说明治理边坡具有三维效应;开挖至3-3煤层底板,开挖坡角20°,弱层暴露宽度为400m,边坡的稳定系数刚好达到安全储备系数1.1,建议矿方首选此方案,可以最大限度的回收煤炭资源。     

Preparation of steel slag porous sound-absorbing material using coal powder as pore former

The aim of the study was to prepare a porous sound-absorbing material using steel slag and fly ash as the main raw material, with coal powder and sodium silicate used as a pore former and binder respectively. The influence of the experimental conditions such as the ratio of fly ash, sintering temperature, sintering time, and porosity regulation on the performance of the porous sound-absorbing material was investigated. The results showed that the specimens prepared by this method had high sound absorption performance and good mechanical properties, and the noise reduction coefficient and compressive strength could reach 0.50 and 6.5 MPa, respectively. The compressive strength increased when the dosage of fly ash and sintering temperature were raised. The noise reduction coefficient decreased with increasing ratio of fly ash and reducing pore former, and first increased and then decreased with the increase of sintering temperature and time. The optimum preparation conditions for the porous sound-absorbing material were a proportion of fly ash of 50% (wt.%), percentage of coal powder of 30% (wt.%), sintering temperature of 1130°C, and sintering time of 6.0 hr, which were determined by analyzing the properties of the sound-absorbing material.