珊瑚碎屑颗粒内孔隙特性微观试验研究∗

珊瑚碎屑是一种特殊的岩土材料,其显著特征是存在大量的内孔隙。为了深入揭示珊瑚碎屑内孔隙特性,通过电镜扫描(SEM)和压汞试验(MIP),分别定性和定量化地分析了珊瑚碎屑颗粒表面及内部孔隙形态特征和分布规律。结果表明:珊瑚碎屑存在由珊瑚虫生长和微生物共生形成的两类大小、形态及分布不同的内孔隙;珊瑚碎屑的整体孔隙度为9%～25%,由珊瑚虫生长而形成的孔隙等效直径为10～200μm;由微生物形成的孔隙面孔隙度低,孔隙直径多为4μm以下,且等轴或不等轴孔隙占绝大部分。     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Photocatalytic activity of Fe-doped CaTiO3 under UV-visible light

The photocatalytic degradation of methylene blue（MB） over Fe-doped CaTiO3 under UV-visible light was investigated. The as-prepared samples were characterized using X-ray diffraction（XRD）, scanning electron microscope（SEM） equipped with an energy dispersive spectrometer（EDS） system, Fourier transform infrared spectra（FT-IR）, and UV-visible diffuse reflectance spectroscopy（DRS）. The results show that the doping with Fe significantly promoted the light absorption ability of CaTiO3 in the visible light region. The Fe-doped CaTiO3 exhibited higher photocatalytic activity than CaTiO3 for the degradation of MB.However, the photocatalytic activity of the Fe-doped CaTiO3 was greatly influenced by the calcination temperature during the preparation process. The Fe-doped CaTiO3 prepared at500°C exhibited the best photocatalytic activity, with degradation of almost 100% MB（10 ppm）under UV-visible light for 180 min.     

Dyes adsorption using a synthetic carboxymethyl cellulose-acrylic acid adsorbent

Removal of noxious dyes is gaining public and technological attention. Herein grafting polymerization was employed to produce a novel adsorbent using acrylic acid and carboxymethyl cellulose for dye removal. Scanning electron microscopy and Fourier-transform infrared spectroscopy verified the adsorbent formed under optimized reaction conditions. The removal ratio of adsorbent to Methyl Orange, Disperse Blue 2BLN and malachite green chloride reached to 84.2%, 79.6% and 99.9%, respectively. The greater agreement between the calculated and experimental results suggested that pseudo second-order kinetic model better represents the kinetic adsorption data. Equilibrium adsorptions of dyes were better explained by the Temkin isotherm. The results implied that this new cellulose-based absorbent had the universaiity for removal of dyes through the chemical adsorption mechanism.     

Comparison of quartz sand, anthracite, shale and biological ceramsite for adsorptive removal of phosphorus from aqueous solution

The choice of substrates with high phosphorus adsorption capacity is vital for sustainable phosphorus removal from waste water in constructed wetlands. In this study, four substrates were used： quartz sand, anthracite, shale and biological ceramsite. These substrate samples were characterized by X- ray diffractometry and scanning electron microscopy studies for their mineral components （chemical components） and surface characteristics. The dynamic experimental results revealed the following ranking order for total phosphorus （TP） removal efficiency： anthracite 〉 biological ceramsite 〉 shale 〉 quartz sand. The adsorptive removal capacities for TP using anthracite, biological ceramsite, shale and quartz sand were 85.87, 81.44, 59.65, and 55.98 mg/kg, respectively. Phosphorus desorption was also studied to analyze the substrates＇ adsorption efficiency in wastewater treatment as well as the substrates＇ ability to be reused for treatment. It was noted that the removal performance for the different forms of phosphorus was dependent on the nature of the substrate and the adsorption mechanism. A comparative analysis showed that the removal of particulate phosphorus was much easier using shale. Whereas anthracite had the highest soluble reactive phosphorus （SRP） adsorptive capacity, biological ceramsite had the highest dissolved organic phosphorus （DOP） removal capacity. Phosphorus removal by shale and biological ceramsite was mainly through chemical adsorption, precipitation or biological adsorption. On the other hand, phosphorus removal through physical adsorption （electrostatic attraction or ion exchange） was dominant in anthracite and quartz sand.     

Ultrasonic preparation of nano-nickel/activated carbon composite using spent electroless nickel plating bath and application in degradation of 2,6-dichlorophenol

Ni was effectively recovered from spent electroless nickel （EN） plating baths by forming a nano-nickel coated activated carbon composite. With the aid of ultrasonication, melamine- formaldehyde-tetraoxalyl-ethylenediamine chelating resins were grafted on activated carbon （MFT/AG）. PdC12 sol was adsorbed on MFT/AC, which was then immersed in spent electroless nickel plating bath; then nano-nickel could be reduced by ascorbic acid to form a nano-nickel coating on the activated carbon composite （Ni/AC） in situ. The materials present were carefully examined by Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy, X-ray photoelectron spectroscopy and electro- chemistry techniques. The resins were well distributed on the inside and outside surfaces of activated carbon with a size of 120 ± 30 nm in MFT/AC, and a great deal of nano-nickel particles were evenly deposited with a size of 3.8 ± 1.1 nm in Ni/MFT. Moreover, Ni/AC was successfully used as a catalyst for ultrasonic degradation of 2.6-dichloronhenol.     

Enhanced struvite recovery from wastewater using a novel cone-inserted fluidized bed reactor

The feasibility of struvite recovery at low （12.5 mg/L） and high （120 mg[L） phosphorus concentrations was studied by constructing a novel fluidized bed reactor with cones （FBRwc） and without cones （FBRwoc）. The crystallization process was continuously operated for 133 days under different hydraulic retention times （HRT = 1-10 hr）, pH （7.5-10）, and molar ratios of Mg/P （0.75-1.75）, N/P （1-10） and Ca/Mg （0-2）. The optimum operating conditions of HRT, pH, Mg/P and N/P molar ratios were found to be 2 hr, 9, 1.25, and 7.5, respectively. Under these optimum conditions, the phosphorus precipitation efficiencies of FBRwc were 93% for low and 98% for high phosphorus influent; however, the efficiencies were 78% and 81% for FBRwoc, respectively. Due to crystal losses at each junction （17%-31%）, the crystal recovery efficiency of FBRwoc was relatively low （47%-65%） for both influent concentrations. However, the losses were minimal in FBRwc, which showed 75% and 92% crystal recovery for low and high phosphorus concentrations, respectively. At low calcium concentration, crystal chemical analysis showed the product to be pure struvite （〉 99%）. The scanning electron microscope and X-ray diffraction results further confirmed that the crystal recovered from FBRwc contained pure struvite, which could be considered a high quality fertilizer. Except HRT, all parameters （pH, Mg/P, N/P and Ca/Mg） were found to be influencing factors for FBRwc performance. Overall, inserting cones in each part of the reactor played a significant role in enhancing struvite recovery from a wide range of phosphorus-containing wastewater.     

Removal of polycyclic aromatic hydrocarbons from aqueous solution by raw and modified plant residue materials as biosorbents

Removal of polycyclic aromatic hydrocarbons （PAHs）, e.g., naphthalene, acenaphthene, phenanthrene and pyrene, from aqueous solution by raw and modified plant residues was investigated to develop low cost biosorbents for organic pollutant abatement. Bamboo wood, pine wood, pine needles and pine bark were selected as plant residues, and acid hydrolysis was used as an easily modification method. The raw and modified biosorbents were characterized by elemental analysis, Fourier transform infrared spectroscopy and scanning electron microscopy. The sorption isotherms of PAHs to raw biosorbents were apparently linear, and were dominated by a partitioning process. In comparison, the isotherms of the hydrolyzed biosorbents displayed nonlinearity, which was controlled by partitioning and the specific interaction mechanism. The sorpfion kinetic curves of PAHs to the raw and modified plant residues fit well with the pseudo second-order kinetics model. The sorption rates were faster for the raw biosorbents than the corresponding hydrolyzed biosorbents, which was attributed to the latter having more condensed domains （i.e., exposed aromatic core）. By the consumption of the amorphous cellulose component under acid hydrolysis, the sorption capability of the hydrolyzed biosorbents was notably enhanced, i.e., 6-18 fold for phenanthrene, 6-8 fold for naphthalene and pyrene and 5-8 fold for acenaphthene. The sorpfion coefficients （Kd） were negatively correlated with the polarity index [（O＋N）/C], and positively correlated with the aromaticity of the biosorbents. For a given biosorbent, a positive linear correlation between logKoc and logKow for different PAHs was observed. Interestingly, the linear plots of logKoc-logKow were parallel for different biosorbents. These observations suggest that the raw and modified plant residues have great potential as biosorbents to remove PAHs from wastewater.     

环球扫描

<正>《自然》2015年2月27日联合国气候委员会拟定下一步计划联合国政府间气候变化专门委员会(IPCC)于2月24日至2月27日在内罗毕召开了会议,会议对气候变化的评估模式作了一些细微的调整。此次变化旨在吸引更多科学家的参与,也在一定程度上促进了发展中国家的代表作为该组织的管理机构参与议事。但基本的气候框架仍将     

基于分形维数的斜坡非饱和带土体大孔隙分布研究

对取自于云南省昭通市头寨滑坡滑源区附近的两个大尺度(25cm×25cm×50cm)土柱样品进行CT扫描,选取典型剖面切片,通过CT值范围将大孔隙分离从而研究土体中的大孔隙分布;计算大孔隙分布分维数(盒维数),研究其大孔隙的不规则特征,结果表明:土体中大孔隙的盒维数随深度增加呈单调递减规律,且与大孔隙度具有显著正相关关系;但大孔隙度只能表征在某一深度上大孔隙的分布多少,而大孔隙的不规则特征则需盒维数表征;最后得到大孔隙的累积大孔隙度与大孔隙孔径(在盒维数为常数时)符合幂函数规律,研究结果有利于利用分形理论建立大孔隙模型,从而研究水分在大孔隙中运动过程。