首页 | 本学科首页   官方微博 | 高级检索  
文章检索
  按 检索   检索词:      
出版年份:   被引次数:   他引次数: 提示:输入*表示无穷大
  收费全文   55篇
  免费   2篇
  国内免费   7篇
安全科学   2篇
废物处理   4篇
环保管理   5篇
综合类   39篇
基础理论   1篇
污染及防治   4篇
评价与监测   8篇
社会与环境   1篇
  2021年   1篇
  2020年   6篇
  2019年   2篇
  2018年   1篇
  2016年   2篇
  2015年   2篇
  2014年   4篇
  2013年   2篇
  2012年   1篇
  2011年   4篇
  2009年   4篇
  2008年   3篇
  2007年   1篇
  2006年   5篇
  2005年   2篇
  2004年   1篇
  2003年   2篇
  2002年   3篇
  2001年   2篇
  2000年   5篇
  1999年   6篇
  1997年   2篇
  1996年   1篇
  1995年   1篇
  1992年   1篇
排序方式: 共有64条查询结果,搜索用时 171 毫秒
1.
优化了气相色谱法测定水质中的内吸磷,当取样量为100 m L时,内吸磷-O方法检出限为0. 30μg/L,测定下限为1. 20μg/L;内吸磷-S方法检出限为0. 80μg/L,测定下限为3. 20μg/L。内吸磷-O和内吸磷-S标准曲线线性良好,相关系数分别为0. 999 2和0. 999 8。不同水质中内吸磷-O的加标回收率为90. 3%~104%,相对标准偏差为3. 6%~9. 2%;内吸磷-S的加标回收率为92. 1%~94. 9%,相对标准偏差为4. 6%~8. 7%。该方法灵敏度高,能有效分离内吸磷-O和内吸磷-S,同时能将内吸磷-O、内吸磷-S与其他有机磷农药类干扰物分离。  相似文献   
2.
利用牛粪生产沼气,并将副产物有效利用是处理牛粪污的有效途径,为提高牛粪厌氧发酵的产气效率和副产物的利用率,整体工艺采用牛粪发酵前固液分离,固体进行好氧发酵回填牛卧床,分离液进行厌氧-好氧发酵,厌氧发酵产生沼气为系统增温,最后液体通过人工湿地处理达标排放。结果表明:对牛粪进行发酵前固液分离,降低了物料的粘度,利于微生物的传质,可以取得较好的产气效果,沼气通过沼气燃烧炉转化为热能为系统增温降低了其他能源的供给,同时湿地的利用也有效地改善了养牛场周边环境,为牛粪污生产沼气工程提供新思路。  相似文献   
3.
Dissolved organic matter (DOM) in soil solution is considered to interact with herbicides enhancing their mobility and promoting subsequent leaching. Batch experiments were conducted to test if free and DOM-bound herbicides can be separated by a DOM-flocculation technique with Cu as a coagulant. DOM was extracted from the H and A horizons of two soils (Terric Histosol, Cumuli-Calcaric Cambisol) and from the O horizon of a forest soil (Humic Cambisol). DOM-solutions (100 mL) were fortified with the herbicides terbuthylazine and pendimethalin (100 μg active ingredient each) and equilibrated for 14 hours. After DOM-flocculation with Cu (addition of 0,5 mM CuCl2) herbicide recovery was determined in the supernatant solutions and in the precipitate of Humic Cambisol-DOM, respectively. Recovery of the herbicides from pure water was 85–99% and was not influenced by the addition of Cu. At low pH (4,8–5,3) DOM-flocculation of different DOM-extracts was insufficient and varied in a range of 18 – 90%. Herbicide recovery from DOM-solutions decreased moderately for terbuthylazine (60–90%) and strongly for pendimethalin (5 – 30%). In general, the addition of Cu caused no further reduction of herbicide recovery from supernatant solutions, except for Humic Cambisol-DOM. The effects of Cu-addition were most evident for pendimethalin (strongly reduced concentration in the supernatant solutions) and were considered to be caused by a flocculation of DOM-bound moieties. Flocculation of Humic Cambisol-DOM increased from 18 – 24% at pH 5 to > 95% at pH 8. However, at this pH the formation of Cu(OH)2 as a sorbing subcomponent of the flocculated matter lead to an overestimation of DOM-bound pendimethalin. Calculating this side effect 6% of pendimethalin added was DOM-bound. Only traces of terbuthylazine (< 1%) were found in the solid matter of flocculated Humic Cambisol-DOM. To sum up, the new approach to separate freely dissolved herbicides from DOM-bound moieties not fully corresponded to our expectations. DOM-flocculation was found to depend strongly on pH-environment influencing not only DOM-herbicide interactions but also the clear separation of DOM-bound herbicides from herbicides in solutions.  相似文献   
4.
介绍了无机纳米材料特殊的理化性质,综述了纳米氧化物、纳米含氧酸盐和碳纳米管等无机纳米材料在放射性核素吸附分离中的研究进展。提出应对纳米材料进行负载、修饰或功能化研究,制备高性能的复合纳米材料,提高其稳定性和选择性;寻求更经济可行的制备方法,降低纳米材料的生产成本,逐步实现产业化;深入研究纳米材料对放射性核素的吸附机理;在辐射效应对纳米吸附剂的结构稳定性影响方面开展研究,并与现有方法作比较,评价其应用的有效性和可靠性。  相似文献   
5.
The goal of this paper is to find methodologies for removing a selection of impurities (H2O, O2, Ar, N2, SOx and NOx) from CO2 present in the flue gas of two oxy-combustion power plants fired with either natural gas (467 MW) or pulverized fuel (596 MW). The resulting purified stream, containing mainly CO2, is assumed to be stored in an aquifer or utilized for enhanced oil recovery (EOR) purposes. Focus has been given to power cycle efficiency i.e.: work and heat requirements for the purification process, CO2 purity and recovery factor (kg of CO2 that is sent to storage per kg of CO2 in the flue gas). Two different methodologies (here called Case I and Case II) for flue gas purification have been developed, both based on phase separation using simple flash units (Case I) or a distillation column (Case II). In both cases purified flue gas is liquefied and its pressure brought to 110 atm prior to storage.Case I: A simple flue gas separation takes place by means of two flash units integrated in the CO2 compression process. Heat in the process is removed by evaporating the purified liquid CO2 streams coming out from both flashes. Case I shows a good performance when dealing with flue gases with low concentration of impurities. CO2 fraction after purification is over 96% with a CO2 recovery factor of 96.2% for the NG-fired flue gas and 88.1% for the PF-fired flue gas. Impurities removal together with flue gas compression and liquefaction reduces power plant output of 4.8% for the NG-fired flue gas and 11.6% for the PF-fired flue gas. The total amount of work requirement per kg stored CO2 is 453 kJ for the NG-fired flue gas and 586 kJ for the PF-fired flue gas.Case II: Impurities are removed from the flue gas in a distillation column. Two refrigeration loops (ethane and propane) have been used in order to partially liquefy the flue gas and for heat removal from a partial condenser. Case II can remove higher amounts of impurities than Case I. CO2 purity prior to storage is over 99%; CO2 recovery factor is somewhat lower than in Case I: 95.4% for the NG-fired flue gas and 86.9% for the PF-fired flue gas, reduction in the power plant output is similar to Case I.Due to the lower CO2 recovery factor the total amount of work per kg stored CO2 is somewhat higher for Case II: 457 kJ for the NG-fired flue gas and 603 kJ for the PF-fired flue gas.  相似文献   
6.
Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe3O4 magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.  相似文献   
7.
PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.  相似文献   
8.
The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.  相似文献   
9.
根现废弃电路板中金属与非金属的有效分选.对后续金属产品的分离提纯至关重要。为此,采用主动脉动气流对PC主板插槽破碎为5-0.5mm粒级的产品进行分选实验.并对实验结果进行正交实验设计和分析,考察不同气流速度和脉动频率对分选效率的影响,建立了综合分选效率经验模型。实验结果表明.在气流速度为2.90m/s,脉动频率为2.33Hz时,综合分选效率可达85.43%。同时,对正交实验的错配物含量进行计算,结果表明,当气流速度从2.76m/s增大到3.04m/s.脉动频率从1.96Hz增大到2.33Hz时,重产物错配物含量从23.70%减小到12.23%.而轻产物错配物含量从2.13%增大到3.86%。  相似文献   
10.
综述了预富集技术在无机痕量分析中的应用,概述了国内外最新进展,介绍了主要技术及方法的特点,大量文献表明预富集技术用于痕量分析取得满意的效果,降低了检测限,提高了灵敏度。  相似文献   
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号