Fe3O4@SA/Ce微球的表征及对染料的吸附特性

以天然高分子化合物海藻酸钠(sodium alginate,SA)为骨架,结合磁性Fe₃O₄和稀土铈离子Ce(Ⅲ)通过溶液反应制备出一种新型的磁性海藻酸铈复合微球(Fe₃O₄@SA;Ce).采用X射线衍射(XRD)、孔结构比表面积分析(BET)、扫描电子显微镜(SEM)、红外光谱(FT-IR)及振动样品强磁计(VSM)对Fe₃O₄@SA;Ce的结构进行了表征,并以直接桃红12B(direct red 12B,DR 12B)和直接橙S(direct orange S,DO S)两种染料为吸附对象,探讨了Fe₃O₄@SA;Ce的吸附剂性能、吸附动力学和热力学.结果表明,Fe₃O₄@SA;Ce对室温下自然pH染料溶液中DR 12B和DO S均表现出良好的吸附效果,吸附量分别可达464 mg·g^-1和730 mg·g^-1.在不同温度下(298、313、328 K),Fe₃O₄@SA;Ce对DR 12B和DO S的吸附过程均可用拟二级吸附动力学方程准确描述.通过等温吸附研究,发现Fe₃O₄@SA;Ce对两种染料的等温吸附较好地符合Freundlich模型.各种表征结果表明,SA与Ce(Ⅲ)和Fe₃O₄交联反应后生成的Fe₃O₄@SA;Ce凝胶球表面有大量深浅不一的褶皱沟纹,形貌发生了显著变化.作为一种绿色环保、制备方法简单、可高效吸附的磁性高分子复合吸附剂,Fe₃O₄@SA;Ce对高浓度染料具有很好的吸附效果,期望能够在染料废水处理中得到广泛应用.     

晋牛矿1303综放面采空区注氮方案研究及数值模拟

为了合理设计采空区注氮防灭火方案，以晋牛煤矿1303综放工作面为研究对象，通过在采空区进、回风侧布置束管监测系统，连续测定采空区气体浓度变化，划分采空区自燃“三带”分布区域,并基于采空区自燃“三带”划分标准和数值模拟的方法，利用流体力学COMSOL计算软件，研究不同注氮量、注氮位置下采空区氧化自燃带的分布规律。研究结果表明:注氮量和注氮位置参数的变化，对氧化自燃带上界限的影响并不显著，而对氧化自燃带的下界限影响比较显著；最合适的注氮位置应该在距离切顶线30 m左右，运用Origin软件得出注氮量与氧化自燃带宽度呈指数关系，由拟合式计算出最优注氮量为386 m3/h，此时氧化自燃带的宽度为31.5 m。     

两种新型涂铁改性砂的过滤性能及反冲洗条件研究

以两种新型涂铁改性石英砂(纳米氧化铁改性砂,Nano-OCS;氧化铁改性砂,IOCS)及普通石英砂(RQS)为研究对象,考察了两种新型改性砂对沉后水腐殖酸及浊度的直接过滤效果,对其反冲洗条件进行优化研究,并对3种滤料的过滤效果进行了比较.结果表明,1滤层厚度为45 cm时,最佳滤速为6 m·h-1;3种滤料对腐殖酸和浊度的直接过滤效果依次为:Nano-OCSIOCSRQS,其中两种涂铁砂对腐殖酸的去除率分别为71.70%和61.61%;2Nano-OCS和IOCS滤柱的反冲洗流程分4步,对应的流程及最佳操作条件为:首先,用0.5 mol·L-1NaOH的溶液浸泡,气冲强度13 L·s-1·m-2,气冲时间6 min;然后,用0.075 mol·L-1的NaOH溶液与空气同时反冲洗,NaOH溶液冲洗强度为8 L·s-1·m-2,气冲强度13 L·s-1·m-2,冲洗时间3 min;接着用0.015 mol·L-1的FeCl3溶液与空气同时反冲洗,FeCl3溶液冲洗强度为8 L·s-1·m-2,气冲强度13L·s-1·m-2,冲洗时间2 min;最后,用清水冲洗,冲洗强度8 L·s-1·m-2,冲洗时间4 min.两种涂铁砂反冲洗前后表面形态结构更加复杂、粗糙度增加,对腐殖酸去除率进一步提高.3当滤层厚度由45 cm增加到80 cm时,Nano-OCS对腐殖酸直接过滤的最高去除率由74.6%提高至80.3%,平均去除率由57.9%提高至68.5%.     

Applying a new method for direct collection, volume quantification and determination of N2 emission from water

The emission of N₂ is important to remove excess N from lakes, ponds, and wetlands. To investigate the gas emission from water, Gao et al. (2013) developed a new method using a bubble trap device to collect gas samples from waters. However, the determination accuracy of sampling volume and gas component concentration was still debatable. In this study, the method was optimized for in situ sampling, accurate volume measurement and direct injection to a gas chromatograph for the analysis of N₂ and other gases. By the optimized new method, the recovery rate for N₂ was 100.28% on average; the mean coefficient of determination (R²) was 0.9997; the limit of detection was 0.02%. We further assessed the effects of the new method, bottle full of water, vs. vacuum bag and vacuum vial methods, on variations of N₂ concentration as influenced by sample storage times of 1, 2, 3, 5, and 7 days at constant temperature of 15°C, using indices of averaged relative peak area (%) in comparison with the averaged relative peak area of each method at 0 day. The indices of the bottle full of water method were the lowest (99.5%-108.5%) compared to the indices of vacuum bag and vacuum vial methods (119%-217%). Meanwhile, the gas chromatograph determination of other gas components (O₂, CH₄, and N₂O) was also accurate. The new method was an alternative way to investigate N₂ released from various kinds of aquatic ecosystems.     

挥发性油藏回注气井控因素分析及措施

文章明确了挥发性油藏天然气回注井控的安全环保关键因素;量化了低渗挥发性油藏天然气回注注入能力,确定注入端各节点安全生产压力分布,攻关相关配套工艺设备,实现安全有效注入;开展室内实验和PVT相态拟合,分析注天然气后天然气和原油性质变化规律,创新非混相驱组分数值模拟参数优化方法,开展带人工压裂裂缝的组分数值模拟,精准确定压力场分布,降低计量及监测不准带来的安全隐患;明确注气井气窜影响因素,优化注采参数,抑制油井气窜,降低生产风险,实现井控安全情况下的天然气驱环保高效开发。     

Comparative study on effect of blending,thermal barrier coating (LHR) and injector nozzle geometry on biodiesel-fuelled engines

Increased petroleum prices, increased threat to the environment from exhaust emissions and global warming have generated intense international interest in developing renewable and alternative non-petroleum fuels for internal combustion engines. Evolving suitable technology for addressing energy crisis creates a continued investigation into the search for sustainable and clean-burning renewable fuels. This work investigates suitability of different non-edible-derived biodiesels such as cotton seed oil methyl ester (COME), Honne oil methyl ester (HnOME) and Rubber seed oil methyl ester (RuOME) to four stroke, single cylinder compression ignition (CI) engine. Engine tests were conducted to study the effect of fuel blending, thermal barrier coating (TBC) or Low Heat Rejection (LHR) and injector nozzle geometry on the performance, combustion and emission characteristics of COME, HnOME and RuOME in the modified CI engine. Blends of biodiesels with diesel were varied from 20 to 80% in steps of 20%. Two thermal barrier coatings of partially stabilized zirconium (PSZ) and aluminium oxide (Al₂O₃) were provided on the engine to make it fully adiabatic. Nozzle injectors of 3, 4 and 5 holes, with size of orifice varied from 0.2 to 0.3 mm size were selected for the study. It was concluded that B20 biodiesel blend, PSZ-coated engine and four hole nozzle injector of 0.2 mm size resulted in overall better engine performance with increased brake thermal efficiency (BTE) and reduced HC, CO, smoke emissions for the fuel combinations tested. Combustion analysis to study the effect of biodiesel blends, LHR coatings, injector nozzle geometry on the performance of the biodiesel-fuelled engine has been presented to give more insight into the behaviour of operation.     

A study on the factor market distortion and the carbon emission scale effect of two-way FDI

Based on the data of 30 Chinese provinces for the period from 2004 to 2015, this paper expounds the carbon emissions effect of two-way foreign direct investment (FDI) from the perspective of scale effect and factor market distortions. This study uses Kaya identity to decompose carbon emission and construct simultaneous equations model to empirically examine the factor market distortion and the carbon emission scale effect of two-way FDI. The results show that the inward foreign direct investment (IFDI) increase regional carbon emission through scale effect and also exacerbates factor market distortion in China, whereas the outward FDI trends reduce carbon emission and reduces factor market distortions in China. The study also shows that human capital, research and development (R&D), trade openness, and capital accumulation are important determinants of two-way FDI. Therefore, the study proposes that IFDI policies should focus on acquiring green technologies. In addition, the domestic enterprises should be encouraged to participate in global business.     

聚氨酯-水泥带压注水封孔测压技术研究

基于传统上向钻孔测压技术的分析,提出一种新型上向孔测压技术—聚氨酯—水泥带压注水封孔测压技术。该技术利用气体渗透性大于液体的弱点,变传统封堵漏气通道为封堵液体泄漏通道,降低封堵漏气难易程度,提高测压成功率;同时利用水作为动力介质和辅助封孔材料,实现主动测压和钻孔带压注浆,隔绝钻孔瓦斯与外界环境的直接接触,提高系统本身测压的可靠性。通过理论分析及与常用测压技术对比表明,该技术用于煤层瓦斯压力测定是完全可行的。     

基于微电荷法的烟气颗粒物浓度检测技术及其应用

目前针对烟气颗粒物浓度的检测方法较多，但均存在不足。详细分析了基于微电荷法的烟气颗粒物浓度检测技术的基本原理和关键的技术难点，介绍了由于微处理器、数字电子技术和材料科学等的飞速发展带来的技术革新，技术的进步为其应用开拓了更为广泛的应用领域并逐步在工业场合得到推广。     

An extension of Multiple Greek Letter method for common cause failures modelling

Common cause failure describes a condition where several components share the same source of failure that causes them to fail or become unavailable simultaneously. The objective of this paper is to present an improved approach to common cause failure modelling within reliability analyses. The currently used methods allow one component to share common characteristics with only one group of components, which may be affected by the same source of failure. Therefore, an improved method was developed, where components can be assigned to several groups of components that are susceptible to faulty operation with respect to their similar characteristics. A mathematical derivation of the method is presented and the theory is applied to smaller theoretical samples and to a simplified real example. The results show that the new method enables a more detailed reliability analysis. The results prove that consideration of common cause failures using the improved method may decrease the system reliability compared to traditional common cause failure consideration. The system reliability decreases more, if the redundant components have more similarities and are therefore assigned to several common cause failure groups.