Drying of granulated wood ash by flue gas from saw dust and natural gas combustion

At the district heating plant of Kalmar, Sweden an on-line unit for production of granulated wood ash for nutrient recycling on forest soils is being applied. Currently, the granules are dried by hot air from an oil-fired burner. The objective of this work was to investigate how drying by flue gas affects the hardening of granules, or impacts their chemical composition and properties. Ninety-six granule samples were treated by flue gas from natural gas combustion in a laboratory pilot scale flue gas generator. CO₂, CO, O₂, C₃H₈ and NO concentrations were varied during the experiment. Additionally, some samples were treated by flue gas from combustion of sawdust at the heating plant in Kalmar. Drying by flue gases did not affect the chemical composition of granules, but minor effects were seen in their mineralogy. The carbonate content was slightly higher in granules treated with flue gas from natural gas combustion compared to the granules dried by hot air only, when measured by wet chemical methods. Results from XRD analysis imply that the calcite content is higher and the portlandite and arcanite content slightly less in granules treated with flue gas from sawdust combustion compared to the granules dried by hot air only. The results from this investigation showed no negative effects on ash granule composition or physical structure by the use of a flue as a drying medium.     

Robust, comparable population metrics through collaborative photo-monitoring of whale sharks Rhincodon typus.

The formulation of conservation policy for species that are rare and migratory requires broad cooperation to ensure that adequate levels of standardized data collection are achieved and that the results of local analyses are comparable. Estimates of apparent survival rate, relative change in abundance, and proportions of newly marked and returning individuals can inform local management decisions while highlighting corresponding changes at other linked research stations. We have applied computer-assisted photo-identification and mark-recapture population modeling to whale sharks Rhincodon typus at Ningaloo Marine Park (NMP), Western Australia, to create a baseline trend for comparison with other regional aggregations of the species. We estimate several ecological parameters of interest, including an average apparent survival rate of 0.55 yr(-1) for sharks newly marked (new) and 0.83 yr(-1) for sharks captured in multiple seasons (philopatric). The average proportion of philopatric sharks is found to be 0.65 of the total population, and we derive an average population growth rate of 1.12 yr(-1) for them. Our analysis uncovered significant heterogeneity in capture and survival probabilities in this study population; our chosen model structures and data analysis account for these influences and demonstrate a good overall fit to the time-series data. The results show good correspondence between capture probability and an available measure of recapture effort, suggesting that unmodeled systematic effects contribute insignificantly to the model fits. We find no evidence of a decline in the whale shark population at NMP, and our results provide metrics of value to their future management. Overall, our study suggests an effective approach to analyzing and modeling mark-recapture data for a rare species using computer-assisted photo-identification and opportunistic data collection from ecotourism to ensure the quality and volume of data required for population analysis.     

Exposure assessment at a PCDD/F contaminated site in Sweden—field measurements of exposure media and blood serum analysis

Background, aim, and scope  

The main pathway for human exposure to the highly toxic polychlorinated-p-dioxins and polychlorinated furans [polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs)] is via dietary intake. Other exposure pathways may, however, be important in close proximity to point sources, such as wood preservation sites, where PCDD/F contaminated chlorophenols (CP) were previously used. In this study, a heavily PCDD/F contaminated CP saw mill site in Sweden was investigated. Human exposure through a broad spectrum of exposure pathways was assessed. Such studies are in demand since the question whether contaminated sites represent a current or future risk can only be answered by detailed site-specific risk assessments.     

Managing Baltic Sea fisheries under contrasting production and predation regimes: ecosystem model analyses

Based on an earlier published ecosystem model, we have explored possible effects of different management scenarios for the Baltic Sea. The scenarios include an oligotrophication of the system, a drastic increase in the number of seals, and changes in the fishery management. From these simulations we conclude that fisheries, seals, and eutrophication all have strong and interacting impacts on the ecosystem. These interactions call for integrated management. The modeling highlights the potential for conflicts among management mandates such as flourishing fisheries, rebuilt seal populations, and substantially reduced eutrophication. The results also suggest that fisheries management reference points have to be adjusted in response to changes in the presence of natural predators or ecosystem productivity.     

Swedish survey on extra structurally abnormal chromosomes in 39 105 consecutive prenatal diagnoses: Prevalence and characterization by fluorescence in situ hybridization

During 7 years (1985–1992), 39 105 consecutive prenatal diagnoses (34 908 amniocenteses and 4197 chorionic villus samples) were made at the five largest clinical genetic laboratories in Sweden. Thirty-one cases of extra structurally abnormal chromosomes (ESACs) were found, giving a total prevalence of 0·8 per 1000. Twelve ESACs were inherited, 14 were de novo and in five the parental origin was unknown. This gives an estimated prevalence of 0·3–0·4 per 1000 for familial and 0·4–0·5 per 1000 for de novo ESACs. Retrospectively, the ESACs were characterized by fluorescence in situ hybridization (FISH). In nine cases, no material was available for this analysis. In 21 of the remaining 22 cases, the chromosomal origin could be identified by FISH. Seventeen of these (81 per cent) were derived from the acrocentric chromosomes, of which 13 originated from chromosome 15 (62 per cent). The most common ESAC was the inv dup(15) (57 per cent). Two cases were derived from chromosome 22, one from chromosome 14, and one from either chromosome 13 or chromosome 21. The four remaining cases consisted to two i(18p)s and two small ring chromosomes derived from chromosomes 4 and 19, respectively.     

Backcasting — a framework for strategic planning

Backcasting is a planning methodology that is particularly helpful when problems at hand are complex and when present trends are part of the problems. When applied in planning towards sustainability, backcasting can increase the likelihood of handling the ecologically complex issues in a systematic and coordinated way, and also to foresee certain changes, even from a self-beneficial point of view, of the market and increase the chances of a relatively strong economic performance. To that end, backcasting should be performed from a set of non-overlapping principles that are general enough to be helpful in the coordination of different sectors of society and in business, as well as to cover relevant aspects of sustainability. Such principles are helpful when developing reliable non-overlapping indicators for monitoring of the development when coordinating various measures from different sectors of the society or within individual firms with each other, and when handling trade-offs in a relevant way. Furthermore, the transition can benefit from being undertaken in a strategic step-by-step manner, by which such investments search for those that combine two qualities: (i) technical flexibility to serve as platforms for future investments in line with non-overlapping principles of sustainability, and (ii) good possibilities of giving relatively fast return on investment. This framework for planning is developed together with the Natural Step, a non-government organization, and in collaboration with a network of scientists and business. Examples are given from firms applying the framework.     

The ecological footprint from a systems perspective of sustainability

Summary

The Ecological Footprint (EF) is a method for estimating the biologically productive area necessary to support current consumption patterns, given prevailing technical and economic processes. By comparing human impact with the planet's limited bioproductive area. this method tests a basic ecological condition for sustainability. The ecological footprint has gained popularity for its pedagogical strength as it expresses the results of its analysis in spatial units that can easily be communicated. Many EF estimates have been performed on a global, national and sulrnationallevel. In this paper. we review the method and critically assess it from a sustainability perspective based on first order principles. We examine: ? Which aspects of sustainability are already covered by existing EF assessments;

? Which further aspects ofsustainability could be made accountable through the EF (such as areas needed to assimilate waste streams that are not yet accounted for in present assessments); and

? Those aspects ofsustainability that cannot be accountable through the EF. Thereby needing complimentary auditing tools.

Since the EF is a measure of renewable biocapacity, we argue that some dimensions of ecological sustainability should not be included in the EF. These include human activities that should be phased out to obtain sustainability, such as emissions of persistent compounds foreign to nature and qualitative aspects that represent secondary uses of ecological areas and do not, therefore, occupy a clearly identifiable additional ecological space. We also conclude that the EF is useful for documenting the overall human use or abuse of the potentially renewable functions and services of nature. Particularly, by aggregating in a consistentway a varity of human impacts, it can effectively identify the scale of the human economy by companson with the size of the biosphere.     

On wear resistance of tool steel

Maintaining a reasonably low cutting tool wear when producing forming tools is a general challenge in the development of new forming tool materials. The tool life of a hot forming tool steel (H13) has been significantly improved by reducing its Si-content from 1.0 to 0.06 wt.%. However, this modified H13 (MH13) also displays a reduced cutting tool life due to higher cutting forces and a stronger tendency to form built up layers (BUE) on the cutting edge. This paper explains why.Gleeble tests of MH13 revealed a significantly higher flow stress in the 820–900 °C temperature interval in MH13 compared to H13. Thermo-Calc simulations showed that when reducing the Si-content from 1.0 to 0.06 wt.% the initial temperature for ferrite-to-austenite transformation (A1) was reduced from 900 °C to 820 °C. Knowing that austenite has totally different mechanical and thermal properties than ferrite, the difference in A1 between the two steels explains the higher cutting forces and higher tendency for BUE-formation. The conclusion is that the difference in machinability between H13 and MH13 is primarily related to their difference in A1.An attempt was also made to find a new tool material composition that can combine the wear resistance of MH13 and the good machinability of H13. Thermo-Calc simulations were performed with slightly modified alloying content without changing its properties as a good forming tool material, with the aim to increase A1. For instance, reducing the Mn content from 0.5 to 0.05 wt.% proved to increase A1 from 820 to 850 °C.