Conservative heavy metal total discharge schemes

Currently, according to Taiwan’s Water Pollution Control Act, the environmental control of waterbodies and water quality depends on the effluent standards and the standard of water quality in the rivers. The Act demands that each stationary pollution source comply with the effluent standard before being discharged into the rivers, and that the overall water quality in the river shall not exceed the declared standard of water quality. To improve the condition of the waterbodies and water quality of the rivers, the Environmental Protection Administration (EPA) in Taiwan has made stricter regulations concerning the discharge standard. Such regulations will help to reduce the weight of individual pollutants discharged; the discharged wastewater, however, will still gradually worsen the water quality of the rivers even after complying with the effluent standard since some of the pollutant dischargers may decrease the concentration of pollutants by diluting the water before discharging; thus, the total weight of metals discharged in the rivers will not be reduced, and the water quality in the areas where the pollutant sources are concentrated will not thereby be significantly improved. To protect the irrigation water and farmlands from being polluted by discharged heavy metals in industrial wastewater, the EPA started controlling the sources in accordance with the total quantity control (TQC) as defined in the Water Pollution Control Act, in the hope of perfecting the environmental protection of waterbodies and water quality, as well as ensuring clean water sources without any pollution for the rivers, land, and people.     

The general utilization of scrapped PC board

The traditional burning process is used to recover copper from scrapped PC board (printed circuit board) but it causes serious environmental problems. In this research a new process was developed which not only prevents pollution problems, but also maximizes the utility of all the materials on the waste board. First, the scrapped PC board was crushed and grounded, then placed in the NH₃/NH₅CO₃ solution with aeration in order to dissolve copper. After distilling the copper NH₃/NH₅CO₃ solution and then heating the distilled residue of copper carbonate, pure copper oxide was obtained with particle size of about 0.2 μm and the shape elliptical. The remaining solid residue after copper removal was then leached with 6 N hydrochloric acid to remove tin and lead. The last residue was used as a filler in PVC plastics. The PVC plastics with PC board powder as filling material was found to have the same tensile strength as unfilled plastics, but had higher elastic modulus, higher abrasion resistance, and was cheaper.     

Age and contributing factors to unlicensed teen motorcycling

This study aims to examine the initial age when teenagers engage in unlicensed motorcycling in Taiwan and the factors contributing to their unlicensed behavior. Data were collected from the retrospective experience of a cohort of senior high school students and a Cox regression model was applied. The results indicated that an estimated 63.4% of the students had experienced riding before the legal age of 18 years. Contributing factors such as whether the students were in a vocational senior high school, male, and in households with higher motorcycle ownership rates led to an earlier riding age; in contrast, a higher degree of parental monitoring, fewer motorcycles in the household, living in Greater Taipei, and an increase in the bus density in the district delayed the ages of beginning motorcycling. The higher minimum licensing age of 18 in Taiwan has caused a debate about its effectiveness because of the high prevalence of unlicensed teenage riding. Measures such as parental monitoring, power- or speed-limited mopeds, training programs, and no duo-passengers should be carefully examined if a policy is to be made on lowering the age limit of motorcycling.     

Modeling microbiological and chemical processes in municipal solid waste bioreactor,part I: Development of a three-phase numerical model BIOKEMOD-3P

The numerical computer models that simulate municipal solid waste (MSW) bioreactor landfills have mainly two components – a biodegradation process module and a multi-phase flow module. The biodegradation model describes the chemical and microbiological processes. The models available to date include predefined solid waste biodegradation reactions and participating species. Some of these models allow changing the basic composition of solid waste. In a bioreactor landfill several processes like anaerobic and aerobic solids biodegradation, nitrogen and sulfate related processes, precipitation and dissolution of metals, and adsorption and gasification of various anthropogenic organic compounds occur simultaneously. These processes may involve reactions of several species and the available biochemical models for solid waste biodegradation do not provide users with the flexibility to simulate these processes by choice. This paper presents the development of a generalized biochemical process model BIOKEMOD-3P which can accommodate a large number of species and process reactions. This model is able to simulate bioreactor landfill operation in a completely mixed condition, when coupled with a multi-phase model it will be able to simulate a full-scale bioreactor landfill. This generalized biochemical model can simulate laboratory and pilot-scale operations in order to determine biochemical parameters important for simulation of full-scale operations.     

IDENTIFICATION OF AQUIFER DISPERSIVITIES: METHODS OF ANALYSIS AND PARAMETER UNCERTAINTY1

ABSTRACT: This paper presents a method for estimating aquifer dispersivities in solute transport models. Sensitivity equations are derived for the calculation of sensitivity coefficients. A modified Gauss-Newton algorithm is used to perform the least-squares minimization. A statistical procedure is outlined to assess reliability of the estimated parameters. The solute transport model is solved by the upstream weighted, multiple cell balance method which combines the concepts of local mass balance and finite element approximations. A one-dimensional solute transport problem in a vertical column system is first used to illustrate the inverse technique. A second example considers the parameter identification problem for three-dimensional solute transport with a unidirectional steady and uniform flow field. The third example solves the parameter identification problem in a three-dimensional, stream-aquifer, solute transport system with steady state flow. Numerical experiments are conducted to study data requirements for parameter identification.     

Locating pollutant emission sources with optical remote sensing measurements and an improved one-dimensional radial plume mapping technique

Previous studies have shown that there was a relatively large amount of uncertainty along the major wind direction in the results of locating emission sources using the one-dimensional radial plume mapping (RPM(1D)) technique based on optical remote sensing measurements. This paper proposes setting up an additional monitoring line that is perpendicular to the original scanning beam geometry to reduce this uncertainty. We first conducted a computer simulation study using the Gaussian dispersion model to generate the downwind concentrations of plumes from 400 source locations in a 201 m × 201 m spatial domain under various wind directions (n = 181). The optical remote sensing instrument was assumed to be at (0, 0) with two perpendicular monitoring lines, each of which had three beam segments of equal length. Each pair of the reconstructed downwind concentration profiles was then used to trace back to the source locations. The results showed that the accuracy of the method and its uncertainty were improved by using the proposed two-line RPM(1D) approach rather than the original one-line RPM(1D) approach at most simulated source locations. In a follow-up field experiment, a tracer gas was released at the coordinate of (100, 100). The release location was covered within the 0.25- to 0.5-probability area of the estimated results, and the distance between the actual and estimated source locations was 18.4 m (9.2% of the longest beam path).     

Application of a constructed wetland for industrial wastewater treatment: a pilot-scale study

The main objective of this study was to examine the efficacy and capacity of using constructed wetlands on industrial pollutant removal. Four parallel pilot-scale modified free water surface (FWS) constructed wetland systems [dimension for each system: 4-m (L)x1-m (W)x1-m (D)] were installed inside an industrial park for conducting the proposed treatability study. The averaged influent contains approximately 170 mg l(-1) chemical oxygen demand (COD), 80 mg l(-1) biochemical oxygen demand (BOD), 90 mg l(-1) suspend solid (SS), and 32 mg l(-1) NH(3)-N. In the plant-selection study, four different wetland plant species including floating plants [Pistia stratiotes L. (P. stratiotes) and Ipomoea aquatica (I. aquatica)] and emergent plants [Phragmites communis L. (P. communis) and Typha orientalis Presl. (T. orientalis)] were evaluated. Results show that only the emergent plant (P. communis) could survive and reproduce with a continuous feed of 0.4m(3)d(-1) of the raw wastewater. Thus, P. communis was used in the subsequent treatment study. Two different control parameters including hydraulic retention time (HRT) (3, 5, and 7d) and media [vesicles ceramic bioballs and small gravels, 1cm in diameter] were examined in the treatment study. Results indicate that the system with a 5-d HRT (feed rate of 0.4m(3)d(-1)) and vesicles ceramic bioballs as the media had the acceptable and optimal pollutant removal efficiency. If operated under conditions of the above parameters, the pilot-plant wetland system can achieve removal of 61% COD, 89% BOD, 81% SS, 35% TP, and 56% NH(3)-N. The treated wastewater meets the current industrial wastewater discharge standards in Taiwan.     

Oxidation of chlorophenols in soil at natural pH by catalyzed hydrogen peroxide: the effect of soil organic matter.

This investigation reports on the effects of soil organic matter (SOM) during the oxidation of chlorophenols with Fe2+-catalyzed H2O2 (Fenton oxidation) system. The soil pH was 7.1 and was not altered. Sorption experiments of soil pre-treated under various oxidation conditions were performed. Concentrations of organic matter in the liquid phase and soil before and after oxidation were analyzed. The results were correlated to the observation in batch Fenton oxidation tests. They showed that the oxidation of chlorophenols at natural soil pH depended on the dose of H2O2 and Fe2+. The soil organic content did not vary significantly after various Fenton treatments, while the sorption of chlorophenols was 10-25% less by the oxidation. The concentration of chlorophenols in the liquid phase exhibited a "decrease and rebound" phenomenon in the batch Fenton oxidation tests. It appeared that the oxidation of SOM resulted in the release of sorbed chlorophenols which were then oxidized by the excess H2O2. An "oxidation-desorption-oxidation" scheme was proposed to describe one of the interaction mechanisms among the oxidant, SOM, and chlorophenols during oxidation.     

Mussel watch: a review of Cu and other metals in various marine organisms in Taiwan, 1991-98

This study presents the distribution of Cu, Zn, Pb, Cd, Hg and As in various marine organisms collected along the western coast of Taiwan from 1991 to 1998, and also evaluates the time variation of Cu in oysters before (1980-85) and after (1986-98) the "green oyster" incident. The results show that relatively high geometric mean (GM) concentrations of Cu, Zn, Pb, Cd, As and Hg were generally found in Crassostrea gigas (Cu=229 microg/g, Zn=783 microg/g), Gomphina aeguialtera (Pb=30.3 microg/g), Tegillarca granosa (Cd=2.85 microg/g), Thais clavigera (As=96.9 microg/g) and Parapenaeopsis cornuta (Hg=1.35 microg/g), respectively. Especially, maximum Cu and Zn concentrations (GM=229 and 783 microg/g, respectively) in oysters (C. gigas) from different culture areas were much higher than those of the other organisms by about 1.13-458 and 2.40-63.7 times, respectively. Similarly, rock-shells (Thais clavigera) had a high capacity for accumulating Cu (GM=202 microg/g) and Zn (GM=326 microg/g) under the same physico-chemical conditions. The highest GM Cu and Zn concentrations of 1108 (range from 113 to 2806) and 1567 (range from 303 to 3593) microg/g were obtained in oysters from the Hsiangshan coastal area, one of the most important oyster culture areas in Taiwan. However, the highest GM Cd and As concentrations of 6.82 and 19.3 microg/g were found in oysters from the Machu Islands. Mean Cu concentrations in the oysters from the Erhjin Chi estuary declined from 2194+/-212 microg/g in 1986-90 to 545 microg/g (GM) in 1991-96. In the Hsiganshan area, GM Cu concentrations of 909 microg/g (1991-96) and 1351 microg/g (1997-98) in oysters were significantly higher than those of 201 microg/g (1980-85) and 682 microg/g (1986-90). The gradually increasing levels of Cu and Zn in the oysters from the Hsiangshan area have been observed year by year.