Contribution of atmospheric emissions to the contamination of leaf vegetables by persistent organic pollutants (POPs): Application to Southeastern France

A modeling approach has been developed to estimate the contribution of atmospheric emissions to the contamination of leaf vegetables by persistent organic pollutants (POPs). It combines an Eulerian chemical transport model for atmospheric processes (Polair3D/Polyphemus) with a fate and transport model for soil and vegetation (Ourson). These two models were specifically adapted for POPs. Results are presented for benzo(a)pyrene (BaP). As expected no accumulation of BaP in leaf vegetables appears during the growth period for each harvest over the 10 years simulated. For BaP and leaf vegetables, this contamination depends primarily on direct atmospheric deposition without chemical transfer from the soil to the plant. These modeling results are compared to available data.     

Removal of trichloroethylene from soil using the hydration of calcium oxide

Quicklime addition to soil at a remediation site was observed to sufficiently reduce TCE levels, but the cause of the removal could not be confirmed with the field data collected. Potential mechanisms for CaO treatment of trichloroethylene (TCE) in soil include degradation and volatilization. Since earlier studies found TCE degradation to occur during the hydration of CaO under conditions where volatilization was limited, research was conducted on mechanisms of TCE removal from soil by CaO application under conditions where volatilization was allowed to occur. TCE volatilization in soil treated with 0%, 5%, 10%, and 20% CaO doses was measured in experiments where the degree of volatilization could be tracked. The total TCE removal from soil spiked with TCE at CaO doses from 5% to 20% ranged from 97% to 99% of the initial TCE mass. Volatilization accounted for 64.4-92.5% of the TCE removal, with unrecovered TCE and TCE degradation accounting for the remaining fraction. The greater heat encountered with higher CaO doses helped minimize obstacles to TCE volatilization, such as high soil organic and clay content. Treatment with a 20% CaO dose, however, led to the formation of byproducts such as dichloroacetylene. TCE degradation to dichloroacetylene at the 20% CaO dose ranged from 2.7% to 6.4% of the initial TCE. Volatilization was concluded to be the dominant process for TCE removal from soil during CaO treatment.     

Factors affecting TCLP lead leachability from computer CPUs

The factors impacting lead leachability from computer central processing units (CPUs) during the toxicity characteristic leaching procedure (TCLP) were investigated. Several CPUs were disassembled and their component materials were decreased in size to meet the requirements of the TCLP. The impact of CPU composition was examined by leaching different combinations of the CPU components. The ferrous metal content of the mixture greatly impacted lead leaching. TCLP lead concentrations of CPUs predicted by leaching the lead-bearing printed wire boards alone were much greater than those measured when the ferrous metal of the CPU was included in the mixture. The leaching of iron and zinc from the galvanized steel components of the CPU created electrochemical conditions where lead was less soluble. Additional size reduction beyond that required by the TCLP did not result in additional lead leaching. As the volume of head space above the leaching solution increased, the concentration of lead measured increased as well.     

Measuring the gypsum content of C&D debris fines

Construction and demolition (C&D) debris recycling facilities often produce a screened material intended for use as alternative daily cover (ADC) at active landfills or for shaping and grading at closed landfills. This product contains soil and small pieces of wood, concrete, gypsum drywall, shingles and other components of C&D debris. Concerns have been raised over the contribution of gypsum drywall in C&D debris fines to odor problems at landfills where the product is used. To address such concerns, limitations may be placed on the percentage of gypsum (or sulfate) that can occur, and standardized testing procedures are required to permit valid compliance testing. A test procedure was developed for measuring the gypsum content in C&D debris fines. The concentration of sulfate leached in an aqueous solution was used to estimate the initial gypsum content of the sample. The impact of sample size and leaching time were evaluated. Precision and accuracy increased with increasing gypsum content. Results from replicate samples had an average relative standard deviation of 9%. The gypsum content of fines obtained from different facilities in the US varied widely from 1% to over 25%. These variations not only occurred between differing facilities, but within batches produced within a single facility.     

The use of newspaper data in historical earthquake studies

Studies of historical British earthquakes are an essential component of assessing seismic hazard in the U.K.; such studies rely heavily on macroseismic data obtained from printed newspapers. This paper discusses the ways in which newspapers have reported British earthquakes and the nature and limitations of the data that may be acquired from this source. Historical changes in the press as a source of macroseismic data are discussed. It is suggested that an understanding of the background and nature of newspaper data is an important component in the process of revaluating historical earthquakes from such data.     

Leachability of printed wire boards containing leaded and lead-free solder

Due to environmental concerns and regulatory initiatives, electronics manufacturers are replacing the tin/lead solder commonly used on printed wire boards (PWBs) with alternative solders. To determine the potential waste management impacts of the alternative solders versus the tin/lead solder, two leaching tests on PWBs manufactured with five alternative types of solder were performed: the toxicity characteristic leaching procedure (TCLP) and the synthetic precipitation leaching procedure (SPLP). These tests are commonly used in the US regulatory community to assess pollutant leachability in different disposal scenarios. The article discusses the application and limitations of these tests. The five types of solders investigated were 63Sn/37Pb, 99.3Sn/0.7Cu, 95.5Sn/4Ag/0.5 Cu, 96Sn/2.5Ag/1Bi/0.5Cu, and 42Sn/1Ag/57Bi. The leaching tests were conducted on four PWB sections, each with a unique configuration and solder density. The largest lead concentrations were observed from the PWBs containing Sn/Pb solder, with concentrations exceeding the hazardous waste toxicity characteristic (TC) in TCLP leachates. Silver, the other regulated element used in the solders, was rarely detected, with none of the samples exceeding the TC limit for silver. High copper concentrations were observed and were determined to result from the PWB itself, not from the copper-containing solders.