Assessment of the interrelation between photooxidation and biodegradation of selected polyesters after artificial weathering

Three commercially available biodegradable polymers, two different aromatic-aliphatic copolyesters and polylactic acid, intended for the fabrication of agricultural mulching films, in addition to other applications, were subjected to a series of tests with the aim of studying the relationship between their photooxidation and biodegradation. Photooxidation resulted in the rearrangement of polymeric chains, in the case of both copolyesters the events led to polymeric chain crosslinking and the formation of insoluble polymeric gel. The tendency was significantly more pronounced for the copolyester with the higher content of the aromatic constituent. As regards polylactic acid photochemical reactions were not accompanied by crosslinking but instead provoked chain scissions. A biodegradation experiment showed that, despite marked structural changes, the extent of photooxidation was not the decisive factor, which significantly modified the rate of biodegradation in all three materials investigated. The specific surface area of the sample specimens was shown to be more important.     

Bio-syngas production with low concentrations of CO2 and CH4 from microwave-induced pyrolysis of wet and dried sewage sludge

This paper assesses the feasibility of producing syngas from sewage sludge via two pyrolysis processes: microwave-induced pyrolysis (MWP) and conventional pyrolysis (CP). The changes in the composition of the produced gas as a function of the pyrolysis treatment and the initial moisture content of the sludge were evaluated. It was found that MWP produced a gas with a higher concentration of syngas than CP, reaching values of up to 94vol%. Moreover, this gas showed a CO2 and CH4 concentration around 50% and 70%, respectively, lower than that obtained in the gas from CP. With respect to the effect of moisture on gas composition, this was more pronounced in CP than in MWP. Thus, the presence of moisture increases the concentration of H2 and CO2 and decreases that of CO, especially when CP was used. In order to elucidate the behaviour of CO2 during the pyrolysis, the CO2 gasification kinetics of the char obtained from the pyrolysis were investigated. It was established that in microwave heating the gasification reaction is much more favoured than in conventional heating. Therefore, the low concentration of CO2 and the high concentration of CO in the microwave pyrolysis gas could be due to the self-gasification of the residue by the CO2 produced during the devolatilization of the sewage sludge in the pyrolysis process.     

Hydrogen production from food wastes and gas post-treatment by CO2 adsorption

The production of H₂ by biological means, although still far from being a commercially viable proposition, offers great promise for the future. Purification of the biogas obtained may lead to the production of highly concentrated H₂ streams appropriate for industrial application. This research work evaluates the dark fermentation of food wastes and assesses the possibility of adsorbing CO₂ from the gas stream by means of a low cost biomass-based adsorbent. The reactor used was a completely stirred tank reactor run at different hydraulic retention times (HRTs) while the concentration of solids of the feeding stream was kept constant. The results obtained demonstrate that the H₂ yields from the fermentation of food wastes were affected by modifications in the hydraulic retention time (HRT) due to incomplete hydrolysis. The decrease in the duration of fermentation had a negative effect on the conversion of the substrate into soluble products. This resulted in a lower amount of soluble substrate being available for metabolisation by H₂ producing microflora leading to a reduction in specific H₂ production.Adsorption of CO₂ from a gas stream generated from the dark fermentation process was successfully carried out. The data obtained demonstrate that the column filled with biomass-derived activated carbon resulted in a high degree of hydrogen purification. Co-adsorption of H₂S onto the activated carbon also took place, there being no evidence of H₂S present in the bio-H₂ exiting the column. Nevertheless, the concentration of H₂S was very low, and this co-adsorption did not affect the CO₂ capture capacity of the activated carbon.     

Influence of physical properties of solid biomass fuels on the design and cost of storage installations

The aim of this work consists on determining biomass fuels properties and studying their relation with fixed and variable costs of stores and handling systems. To do that, dimensions (length and diameter), bulk density, particle density and durability of several brands and batches of wood pellets and briquettes were tested, according to international standards. Obtained results were compared with those in literature. Bulk density tests were applied for several other biomass fuels too, and later used to determinate which ones of all the biomass-fuels tested are economically more profitable for a typical transport/store system made of a screw conveyor and a concrete bunker silo.