Wet oxidative regeneration of activated carbon loaded with reactive dye

Wet Oxidative Regeneration (WOR) of powdered activated carbon (PAC) and granular activated carbon (GAC) loaded with the reactive dyes, namely chemictive brilliant blue R and cibacron turquoise blue G, was studied. Attempts were made to regenerate the loaded carbons designated now as spent carbon. A slurry (10% w/v) of spent carbon in distilled water was oxidized by wet oxidation in the temperature range of 150-250 degrees C using oxygen partial pressures between 0.69-1.38 MPa in an 1 1 SS 316 autoclave. The percent regeneration was determined from a ratio, X(RC)/X(VC), corresponding to an equilibrium adsorption capacity of regenerated carbon/equilibrium adsorption capacity of virgin carbon from an initial adsorption period of 3 h. It was observed that the regeneration mainly occurred due to the oxidation of the adsorbates taking place on the surface of carbon. It was possible to regenerate the spent GAC and PAC to the extent of more than 98% (approximately X(RC)/X(VC) > 0.98) by wet oxidation. After four consecutive cycles of adsorption and regeneration using the same stocks of GAC, carbon weight loss observed at 200 degrees C was about 40%. SEM studies of the regenerated carbon showed widening of the pores and loss of structure between the adjacent pores as compared with the virgin carbon. PAC was found to be more suitable as compared with GAC for the adsorption and wet oxidative regeneration processes to treat the aqueous solution containing lower concentration of unhydrolyzed reactive dye. The suitability of wet oxidative regeneration is demonstrated at a bench scale to treat the synthetic reactive dye solution.     

A review on comparative study of Savonius wind turbine rotor performance parameters

One approach for reducing the level of environmental contamination threats around the world is to use renewable energy-harvesting equipment. Wind is a potential environmental resource that has become a desirable aspect of urban use due to advances in wind turbine design technology. Other variants have been developed based on the classic vertical-axis Savonius rotor model, which, according to experimental test findings and computational calculations, show higher operational characteristics performance. Generated power and shaft torque operational results are obtained by providing specific rotor blade shapes in these models, one of the most common designs, among small-scale rotor which uses a drag-based vertical axis whereas Savonius turbines having large-scale rotors not developed yet. This kind of rotor has the advantages of being simple to design, affordable, performing well at low speeds, and turns to flow direction independently. However, it was discovered that the Savonius rotor suffers through high quantity of negative torques created by the returning blade after a number of examinations into its performance. Many studies on various rotor types have been conducted to resolve the Savonius turbine’s performance constraints. The research showed and analyzed the difficulties and modification in design parameters of rotor, as well as their major impact on rotor performance.

     

Large-scale synthesis and antibacterial activity of fungal-derived silver nanoparticles

There is a demand for environmentally friendly processes to synthesize nanoparticles. Here, we synthesized silver nanoparticles using encapsulated biomass beads of Phoma exigua var. exigua. Nanoparticles were characterized by nanoparticle tracking and analysis (NTA), Fourier-transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy and zeta potential. Results of NTA show that nanoparticle size was homogenous. Concerning nanoparticle stability, zeta potential decreased with batch number. Silver nanoparticles exhibited an antibacterial activity against Escherichia coli and Staphylococcus aureus. Overall, the encapsulation of fungal biomass by calcium alginate for the batch synthesis of silver nanoparticles was easy, cost-effective, eco-friendly and suitable for the large-scale synthesis of silver nanoparticles. We have also demonstrated the reusability of the fungal biomass during biosynthesis of silver nanoparticles using the sodium alginate encapsulation method.     

Anaerobic treatment of slaughterhouse wastewater: a review

This article presents a review of anaerobic treatment technologies to treat slaughterhouse wastewater including its advantages and disadvantages. Physico-chemical characteristics and biochemical methane potential (BMP) of slaughterhouse wastewater are addressed. Various anaerobic treatment technologies are presented with the related operating parameters, viz., hydraulic retention time (HRT), organic loading rate (OLR), upflow velocity (V_up), and biogas yield vis-a-vis treatment efficiency in terms of chemical oxygen demand (COD). In addition, various factors that affect the anaerobic treatment of slaughterhouse wastewater such as high oil & grease (O & G) concentration in influent, inhibitors, volatile fatty acids (VFAs), and the loading rate are also addressed. The literature review indicated that the slaughterhouse wastewater can be treated effectively by employing any anaerobic treatment technologies at OLRs up to 5 kg COD/m³.d with more than 80% COD removal efficiency without experiencing operational problems. Anaerobic hybrid reactors (AHRs) were found the most effective among various reviewed technologies because of their ability to operate at higher OLRs (8 to 20 kg COD/m³.d) and lower HRTs (8 to 12 hrs).

     

Perspective of reactive separation of levulinic acid in conceptual mixer settler reactor

Environmental Science and Pollution Research - Levulinic acid is a carboxylic acid present in industrial downstream. It is an important chemical and can be transformed into various important...     

Fungicidal activity of Cu nanoparticles against <Emphasis Type="Italic">Fusarium</Emphasis> causing crop diseases

In India more than 60 % of the population relies on crops for their livelihood. However, crop diseases are one of the major factors limiting productivity. Hence, nanotechnology appears as a new means to control diseases and enhance yield. Here, stable copper nanoparticles were synthesized using cetyl trimethyl ammonium bromide and copper nitrate at room temperature, then characterized by UV–Visible spectrophotometry, X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and zeta potential measurement. The antifungal activity was evaluated against three common crop pathogenic Fusarium spp. We found that stable copper nanoparticles synthesized using 0.030 M cetyl trimethyl ammonium bromide and 0.003 M copper nitrate have the maximum activity against Fusarium equiseti with a 25 mm zone of inhibition, followed by F. oxysporum (20 mm) and F. culmorum (19 mm).     

Biofabrication of calcium phosphate nanoparticles using the plant Mimusops elengi

Nanoparticles are now widely applied in products. The synthesis of nanomaterials using biological materials is an emerging field, notably for medical applications because biologically derived compounds can be safe. For instance, calcium phosphate is a natural biomineral that possesses an excellent biocompatibility due to its chemical similarity to human hard tissue such as bone and teeth. Here, we synthesized calcium phosphate nanoparticles by using bark extract of Spanish cherry (Mimusops elengi). Calcium phosphate nanoparticles showed an absorbance at 275 nm by UV–visible analysis and particle size of 25 nm by nanoparticle tracking and analysis. Fourier transform infrared spectroscopy revealed the presence of aromatic amines as a capping and reducing agent. Transmission electron microscopy showed the presence of polydispersed spherical nanoparticles with an average size of 50 nm. Measurements of zeta potential revealed the stability of the synthesized calcium phosphate nanoparticles. These particles demonstrated antibacterial activity against Streptococcus mutans, Staphylococcus aureus and Escherichia coli. We conclude that the synthesis of calcium phosphate nanoparticles by using a M. elengi is easy, eco-friendly and scalable.