A laboratory study on migration of K+ in a two-layer landfill liner system.

Contaminant transport through the clay liner and the underIying secondary leachate drain layer (SLDL) in landfills was studied through a laboratory test, and analysis method on the transport of K+ in a two-layer soil system. The soils used for this study were Ariake clay and the underlying layer, Shirasu soil from the Kyushu region of Japan, representing the clay liner material and SLDL material, respectively. The effective diffusion coefficients (De) of the selected target chemical species, potassium (K+) for the Ariake clay and Shirasu soil were back-calculated using a computer program, and it was found that values of De derived from this study were consistent with those previously published. The hypothesis that the mechanical dispersion process can be negligible has been proved to be reasonable based on both the observation that the predicted values fit the experimental data and the analyses of two dimensionless parameters. Parametric analysis showed the transport of K+ through the soils is controlled by advection-diffusion rather than diffusion only, whereas at low Darcy velocity (i.e. < or = 10(-9) m s(-1)), transport of K+ would be controlled by diffusion. The test results and parametric analysis may be applied in design of landfill liners and SLDLs, particularly in coastal areas.     

Leaching characteristics of bisphenol A from epoxy-resin pavement materials

We investigated the leaching characteristics of bisphenol A (BPA) from two kinds of epoxy-resin pavement materials, one containing epoxy resins (EPs) and the other containing epoxy-acrylate resins (EPAs). Both samples contained residual BPA monomer, at levels of 9.0?µg?g^?1 for the EP resin sample and 4.4?µg?g^?1 for the EPA resin sample. These amounts were larger than amounts previously measured for polycarbonate samples. The amount of BPA leached from the samples increased with temperature. The leaching of BPA from EP was more strongly affected by temperature than the leaching from EPA. The pH also affected the amount of leached BPA. The maximum leached amount was observed under alkaline conditions (pH 10.8) for both sample types. The amounts of BPA that might leach from pavement materials during 1?h of heavy rain were estimated to be 0.9?µg?m^?2 for EP and 3.5?µg?m^?2 for EPA. Our results indicate that EPs disposed of in waste landfills without any treatment may be a source of BPA in leachate at landfill sites.     

Exoenzymes of Trametes versicolor can metabolize coplanar PCB congeners and hydroxy PCB

Two fractions containing the oxidase activity toward 2,2'-azinobis (3-ethylbenzothiazoline-6-sulfonate) (ABTS) were obtained using ion-exchange DEAE-Sepharose column chromatography of the culture fluid of white-rot fungus, Trametes versicolor. These two fractions can reduce the level of coplanar PCB congeners (Co-PCBs). The ABTS oxidase in the first fraction passed through the DEAE-Sepharose column. The ABTS oxidase in the second fraction was adsorbed to the column at 相似文献   

Reality and risk of contact-type head injuries related to bicycle-mounted child seats

Objective

The authors have treated numerous children who have been injured by falling from bicycle-mounted child seats. Despite the greatly increased use of such seats, the understanding of their risk and the importance of helmet use remains alarmingly poor. The objective of this study was to confirm the risk of bicycle-mounted child seats and to evaluate the efficacy of helmets, seat belts, and back seat height in terms of preventing or mitigating contact-type head impacts that occur in falls from bicycle-mounted child seats.

Materials and methods

Biometrical dummy tests were performed to examine contact-type head injuries in falls from stationary bicycles. A bicycle with an anthropometric test dummy placed in a bicycle-mounted child seat was tipped over. Each test was repeated three times and three-dimensional acceleration was measured using accelerometer. Head Injury Criteria (HIC) were calculated and the respective influences of a helmet, a seat belt, and increased height of the back of the seat on such impacts were evaluated.

Results

Only helmets unequivocally lowered maximal acceleration and/or HIC values with statistical significance. The seat belt lowered HIC values as long as it was used with the high-back seat. Only when the dummy wore a helmet sitting in a high-back seat did the HIC show less than the threshold of 570 for three-year-old children. The HIC showed the lowest score of 161.5 when the dummy wore both a helmet and a seat belt sitting in a high-back seat.

Conclusions

Riders in bicycle-mounted child seats definitely have higher risks of contact-type head injuries. In transporting a child on a bicycle-mounted child seat, parents must use both a child-bicycle helmet and a high-back child seat at least; a seat belt is highly recommended as long as it is used with the other safety devices.

Impact on Industry

The bicycle-mounted child seat should have a high enough back and an appropriate seat belt to protect the head of the child from a contact-type injury.     

Study on dechlorination technology for municipal waste plastics containing polyvinyl chloride and polyethylene terephthalate

It is necessary to remove chlorine efficiently from municipal waste plastics (MWP) that contain polyvinyl chloride (PVC) and other plastics containing chlorine. In this article we consider thermal degradation liquefaction technology. In Japan, the chlorine content of reclamation oil products must be kept below 100 ppm owing to the quality standard for pyrolysis oil. Liquefaction dechlorination technology for MWP is still an important issue to study. The twin-screw extruder that has been developed as dechlorination technology for blast furnaces and coke ovens has a shorter residence time for dechlorination than other dechlorination technologies. In this article, we used a single-screw extruder for the dechlorination process because it also has a short residence time. Experiments on the dechlorination process were carried out by using a single-screw extruder to assess its dechlorination performance. Practical use of the single-screw was demonstrated by the operation of a commercial oil reclamation plant operated by Sapporo Plastic Recycle Co., Ltd. (SPR). Moreover, an investigation of cascade recycling was carried out in 2008 in which material recycle wastes were mixed with MWP and processed by chemical recycling (liquefaction). It was demonstrated that cascade recycling is an efficient recycling combination and contributes to local feedstock recycling. However, it was shown that MR wastes affect the quality of the reclamation oil when they make up more than 40% of the feed mix. If the quantity of MR wastes is kept below 40%, the reclamation oil is able to meet the quality standard. The SPR plant can be operated safely and in a stable manner.     

Production and characterization of KOH-activated carbon derived from polychlorinated biphenyl residue generated by the sodium dispersion process

Polychlorinated biphenyl (PCB) residues from the sodium dispersion (SD) process were employed as the raw materials for the production of activated carbon using KOH activation. The pore properties, such as the specific surface area and pore size distribution, were characterized using the Barrett–Joyner–Halenda method and the Horvath–Kawazoe method based on the N₂ adsorption isotherm at 77 K. The activated carbon produced showed similar adsorption capacities and specific surface areas to the commercially available product. The effects of the activation conditions on the porosity of the activated carbon produced were studied. The most significant factor affecting the specific surface proved to be the activation temperature. The activated carbon produced from PCB residues from the high-temperature (423–443 K) SD process had a binary pore size distribution well developed in the 4 nm region and in the micropore region. The pore structure of the carbon produced from PCB residues from the low-temperature (333–393 K) SD process had a wide range of micropores and mesopores.     

Characterization of metal concentration,heavy metal elution,and desalination behavior of municipal solid waste incineration bottom and grate sifting deposition ash based on particle size

Resource and environmental safety protocols of incineration residues were evaluated by analyzing the metal concentration, heavy metal elution, desalination behavior, and chlorine removal ratio owing to particle size differences between bottom ash (BA) and grate sifting deposition ash (GA). In the total content test, Cl, Zn, and Cr in the incinerator BA exceeded the cement acceptance standard (Cl: 1000 mg/kg; Zn: 1700 mg/kg, and Cr: 170 mg/kg) at almost all of the particle sizes, while Au, Ag, Pd, and Zn had high contents in the GA. When using BA as a construction material, heavy metal elution values and contents are restricted as per the product quality standards based on the Japanese soil pollution control law. Lead within the BA and GA exceeded the standard values for most particle sizes. We predicted that there would be a limit on the elution of K by only washing with water. The removal ratio of total chlorine by particle size was approximately 20–70%, where the effect of the particle size on the removal ratio was small, suggesting that the elution of chlorine was complete in approximately 6 hours. These results contribute to information on the recycling of BA and GA.