Assessment of hydrothermally modified fly ash for the treatment of methylene blue dye in the textile industry wastewater

Dyes and pigments are one of the major water pollutants and if not discharged properly cause ecological disturbance. Considering this, the current study investigates the application of thermal power plant by-product, i.e., fly ash for the elimination of a hazardous methylene blue dye from its synthetic aqueous solution. Experiments were conducted in batch mode to study the effect of pH, temperature, adsorbent dose and contact time. Highest dye removal (94.3%) was achieved at pH 10 using adsorbent dose of 10 g/L in 90 min of contact time at 40 °C. However, for cost-effective operation at neutral pH and room temperature (30 °C), it yields 89.3% dye removal having similar dose and contact time. Equilibrium isotherms for adsorption were analyzed by Langmuir and Freundlich, Temkin and Dubinin–Radushkevich isotherm equations. The results revealed that the best fit model of adsorption closely followed Langmuir adsorption. Based on adsorption isotherm models, thermodynamics parameters ΔG, ΔH and ΔS were calculated. The negative value of ΔG and ΔH revealed that adsorption process was exothermic, spontaneous and physical. The present work suggests that through simple process hydrothermally modified fly ash has the potential to be used as cost-effective and efficient adsorbent for the treatment of wastewater from textile industries.     

Valorisation of used cooking oil sludge by codigestion with swine manure

The addition of lipid wastes to the digestion of swine manure was studied as a means of increasing biogas production. Lipid waste was obtained from a biodiesel plant where used cooking oil is the feedstock. Digestion of this co-substrate was proposed as a way of valorising residual streams from the process of biodiesel production and to integrate the digestion process into the biorefinery concept.Batch digestion tests were performed at different co-digesting proportions obtaining as a result an increase in biogas production with the increase in the amount of co-substrate added to the mixture. Semi-continuous digestion was studied at a 7% (w/w) mass fraction of total solids. Co-digestion was successful at a hydraulic retention time (HRT) of 50 d but a decrease to 30 d resulted in a decrease in specific gas production and accumulation of volatile and long chain fatty acids. The CH₄ yield obtained was 326 ± 46 l/kg VS_feed at an HRT of 50 d, while this value was reduced to 274 ± 43 l/kg VS_feed when evaluated at an HRT of 30 d. However these values were higher than the one obtained under batch conditions (266 ± 40 l/kg VS_feed), thus indicating the need of acclimation to the co-substrate. Despite of operating at low organic loading rate (OLR), measurements from respirometry assays of digestate samples (at an HRT of 50 d) suggested that the effluent could not be directly applied to the soil as fertiliser and might have a negative effect over soil or crops.     

Comparative efficacy of mitigation techniques for the detoxification of Prunus persica (L.) from selected pesticide residues

Environmental Science and Pollution Research - Fruits are the valuable and important components of human diet. Among them, Prunus persica is a rich source of different minerals and dietary fibers....     

Integrated hydrologic–economic decision support system for groundwater use confronting climate change uncertainties in the Tunuyán River basin,Argentina

This study presents an integrated hydrologic–economic model as decision support system for groundwater use and incorporates uncertainties of climate change. The model was developed with the Vensim software (Ventana Systems) for system dynamic simulations. The software permitted the integration of economic variables along with hydrologic variables, in a unified format with the aim of evaluating the economic impacts of climate change on arid environments. To test the model, we applied it in one of the upper Tunuyán River sub-basin, located in the Mendoza Province (Argentina), where irrigation comes from groundwater. The model defines the best mix of crops and the total land use required to maximize the total river sub-basin monetary income, considering as a limit the amount of water that does not exceed the natural annual aquifer recharge. To estimate the impacts of climatic changes, four scenarios were compared: the business as usual (with the number of existing wells) in a dry year with a temperature increase of 4 °C; the business as usual in a wet year with an increase in temperature of 1.1 °C; an efficient use of wells in a dry year and a temperature increase of 4 °C and an efficient use of wells in a wet year with a temperature increase of 1.1 °C. Outputs calculated by the model were: land use per crop, total sub-basin net benefit, total sub-basin water extraction, water extraction limit depending on river discharge and total number of wells required to irrigate the entire area. Preliminary results showed that the number of existing wells exceeded the optimized number of wells required to sustainably irrigate the entire river sub-basin. Results indicated that in an average river discharge year, if wells were efficiently used, further rural development would be possible, until the limit of 350 million m³ of water extraction per year was reached (650 million m³ for a wet year and 180 million m³ for a dry year). The unified format and the low cost of the software license make the model a useful tool for Water Resources Management Institutions, particularly in developing countries.     

Effects of Filler Content and Compatibilizing Agents on Mechanical Behavior of the Particle-Reinforced Composites

The study was carried out to investigate the effects of filler content and two different compatibilizing agents (Eastman G-3003 and G-3216) on the mechanical properties of polypropylene reinforced with corn stalk and wood flour. In the sample preparation, three levels of filler loading (30, 40 and 50 wt%) and one level of compatibilizing agent content (2.5 wt%) were used. For overall trend, with addition of both grades of the compatibilizing agents, tensile and flexural properties of the composites significantly improved, as compared with the pure PP. Tensile and flexural properties reach a maximum at 40 wt% filler content and gradually decrease with a further increase in wood particle content. The composites treated with G-3003 gave better results in comparison with G-3216. This could be caused by the high melt viscosity of G-3003. In general, corn stalk flour filled composites showed superior mechanical properties.     

The evolving trends of landfill leachate treatment research over the past 45 years

Environmental Science and Pollution Research - Landfilling is one of the most prevalent waste management strategies on a global scale. However, one major drawback of landfills is the production of...     

External force-assisted laser forming process for gaining high bending angles

Laser forming process is used in forming and bending of metallic and non-metallic sheets. Laser beam irradiation causes a localized temperature increase and a localized mechanical strength decrease. In this article, an external mechanical force is added to a laser beam irradiation, which is called external force-assisted laser forming process, to gain a 90-degree bending angle. Furthermore, Numerical simulation of the process is performed to achieve a good understanding of the process. Simulation results show that more than two-third of the final forming is due to the laser beam irradiation. Equivalent plastic strain values during laser forming and external force-assisted laser forming processes are compared. Results show that equivalent plastic strain in laser forming process increases in a step pattern, with increasing in scan pass numbers. This occurs because when the laser beam irradiates on the sheet surface, it reduces the yield strength of the sheet. Equivalent plastic strain in external force-assisted laser forming process has an oscillatory step nature. This attributes to simultaneous effects of strain hardening and thermal induced reduction of yield strength of the sheet. Simulations were in good accordance with experiments.