Wind direction bias in generating wind roses and conducting sector-based air dispersion modeling

Certain widely used wind rose programs and air dispersion models use an overly simple data-transfer algorithm that induces a directional bias in their output products. The purpose of this paper is to provide a revised algorithm that corrects the directional bias that occurs from the aliasing that occurs when the sector widths used to report wind direction data are on the same order of magnitude, but not equal, to the sector widths used in the wind direction summaries. The directional bias issue arises when output products in 16 direction sectors (22.5 degrees each) are produced from wind direction data reported in terms of 36 sectors (10 degrees each). The result directional bias affects the results of simulations of air and surface concentrations using widely applied air dispersion models. Datasets or models with the directional bias discussed here give consistent positive biases (approximately 30%) for cardinal direction sectors (north, south, east, and west) and consistent negative biases for all of the other sectors (around -10%). Data summary and air dispersion programs providing outputs in direction sectors that do not match the observational sectors need to be checked for this bias. A revised data-transfer algorithm is provided that corrects the directional bias that can occur in transferring wind direction data between different sector widths.     

Variation in PAH inputs and microbial community in surface sediments of Hamilton Harbour: implications to remediation and monitoring

Variations in concentrations of polycyclic aromatic hydrocarbons (PAHs) and microbial community indicators were investigated in representative highly contaminated and less contaminated surface sediment sites of Hamilton Harbour. Inputs of PAH to the upper 3cm of sediments up to four times the average upper sediment concentrations were observed. Associated PAH fingerprint profiles indicated that the source was consistent with the PAH source to the industrial region of the harbour. Increased PAH loadings were associated with decreased bacterial populations as indicated by phospholipid fatty acid (PLFA) concentrations. However, relatively minor impacts on overall community composition were indicated. Porewater methane concentrations and isotopic data indicated a difference in the occurrence of methane oxidation between the two sites. This study confirms temporally limited transport of contaminants from highly impacted regions as a vector for contaminants within the harbour and the impact on microbial carbon cycling and bed stability.     

Use of an In Situ Erosion Flume for Measuring Stability of Sediment Deposits in Hamilton Harbour,Canada

An in situ erosion flume was used to measure the stability of sediment deposits in Hamilton Harbour, Ontario, Canada. The flume consists of a rectangular duct with an opening at the bottom. A submerged pump attached to the downstream end of the flume circulates the ambient water through the flume, thereby generating turbulent shear flows inside the flume. When the flume rests on a sediment deposit, the exposed part of the sediment deposit is subjected to the flow shear stress. By applying a continually increasing flow shear stress on the sediment deposit and by measuring the amount of sediment erosion, it is possible to assess the erosional stability of the sediment deposits. An under water video camera was mounted on the flume to get visual images of the sediment erosion process. The flume was used at two sites in the Harbour. The erosional resistances measured by the flume for the two sites were different. Measurement of dry density of the sediment deposits using an ultrasonic device was carried out to explain the differences in the stability of sediment deposits from the two sites.     

Distribution of lead, copper and zinc in size-fractionated river bed sediment in two agricultural catchments of southern Ontario, Canada

Metal (Pb, Cu and Zn) partitioning in six separated sediment size fractions (<8, 8-12, 12-19, 19-31, 31-42, 42-60 microm) of river bed sediment have been analyzed by sequential extraction. The concentrations of some major elements (Si, Al, Ca, Mg, K, Na, Fe, Mn and P), and organic and inorganic C were determined to correlate the elemental composition of the sediment with metal speciation and grain size. Results show that Zn and Pb concentrations increase with decreasing grain size. For Big Creek and Big Otter Creek, respectively, the highest concentrations of Zn (326 and 230 mg kg(-1)) and Pb (158 and 67 mg kg(-1)) were found in the smallest (<8 microm) fraction, whereas the Cu levels (619 and 1281 mg kg(-1)) were most abundant in the second smallest (8-12 microm) fraction. The major accumulative phases for Cu, Zn and Pb were carbonates, Fe/Mn oxides and organic matter, but the relative importance of each phase varied for individual metals and grain sizes. The extraction data show increasing potential bioavailability of metals with decreasing grain size. Estimates of metal yields in the study catchments suggest that over 80% of the metal yield in sediment smaller than 63 microm is associated with solids smaller than 31 microm.     

Interactions between Sediment and Water: Perspectives on the 10th International Association for Sediment Water Science Symposium

The 10^th International Symposium on Interactions Between Sediment and Water was held in Lake Bled, Slovenia from August 28 to September 3, 2005. Approximately 155 delegates, attended the symposium where talks and posters addressed five themes incorporating the physical, chemical, biological, and/or management aspects of lacustrine, reverine, estuarine, and/or marine sediment were presented. A review of the symposium themes and plenary talks was provided. As well, this symposiums’ focus is put into context with respect to historical changes noted over the 29 years that the International Association for Sediment Water Science (IASWS) has been meeting.     

Hydrodynamic treatment of wastewater effluent flocs for improved disinfection

Hydrodynamic forces generated by an orifice plate under low pressure were examined as a means of disrupting flocs, in order to improve disinfection of treated wastewater effluents. Changes in cavitation conditions were found to have little impact on the extent of particle breakage in this experimental setup. The rate of strain (flow rate divided by the hole radius cubed), however, was found to be the best predictor of floc breakage. Floc breakage was not affected by changes in floc concentration, but was very sensitive to differences between flocs collected from different sources. Larger flocs (90 to 106 microm) were broken apart to a greater extent than smaller ones (53 to 63 microm). Hydrodynamic treatment decreased the viability of bacteria associated with large flocs, and also increased the ultraviolet dose response by up to one log unit (i.e., a factor of ten). Subjecting final effluent wastewaters to hydrodynamic treatment, therefore, provides a treatment strategy for conditions in which the presence of flocs limits the level of disinfection that can be achieved.     

Compartmentalization of metals within the diverse colloidal matrices comprising activated sludge microbial flocs

Activated sludge floc from a wastewater treatment system was characterized, with regard to principal structural, chemical, and microbiological components and properties, in relation to contaminant-colloid associations and settling. Multiscale analytical microscopies, in conjunction with multimethod sample preparations, were used correlatively to characterize diverse colloidal matrices within microbial floc. Transmission electron microscopy, in conjunction with energy dispersive spectroscopy (EDS), revealed specific associations of contaminant heavy metals with individual bacterial cells and with extracellular polymeric substances (EPS). Floc structure was mapped from the level of gross morphology down to the nano-scale, and flocs were described with respect to settling properties, size, shape, density, porosity, bound water content, and EPS chemical composition; gross surface properties were also measured for correlation with principal floc features. Compartmentalization results based on 171 EDS analyses and representative high-resolution images showed that nano-scale agglomerations of (i) silver (100%) and (ii) zinc (91%) were confined almost entirely to EPS matrices while (iii) Pb (100%) was confined to intracellular granules and (iv) aluminum was partitioned between EPS matrices (41%) and intracellular matrices (59%). The results suggest that engineered changes in microbial physiology and/or in macromolecular EPS composition may influence metal removal efficiencies.