Investigations of ash fouling with cattle wastes as reburn fuel in a small-scale boiler burner under transient conditions

Fouling behavior under reburn conditions was investigated with cattle wastes (termed as feedlot biomass [FB]) and coal as reburn fuels under a transient condition and short-time operation. A small-scale (30 kW or 100,000 Btu/hr) boiler burner research facility was used for the reburn experiments. The fuels considered for these experiments were natural gas (NG) for the ashless case, pure coal, pure FB, and blends of coal and FB. Two parameters that were used to characterize the ash "fouling" were (1) the overall heat-transfer coefficient (OHTC) when burning NG and solid fuels as reburn fuels, and (2) the combustible loss through ash deposited on the surfaces of heat exchanger tubes and the bottom ash in the ash port. A new methodology is presented for determining ash-fouling behavior under transient conditions. Results on the OHTCs for solid reburn fuels are compared with the OHTCs for NG. It was found that the growth of the layer of ash depositions over longer periods typically lowers OHTC, and the increased concentration of ash in gas phase promotes radiation in high-temperature zones during initial periods while decreasing the heat transfer in low-temperature zones. The ash analyses indicated that the bottom ash in the ash port contained a smaller percentage of combustibles with a higher FB percentage in the fuels, indicating better performance compared with coal because small particles in FB burn faster and the FB has higher volatile matter on a dry ash-free basis promoting more burn out.     

Growth and development of cellular slime mould Dictyostelium discoideum treated with DDT

The effects of dichlorodiphenyl trichloroethane (DDT) on the growth, phagocytic activity, ultrastructure and developmental stages of a well known species of the cellular slime mould, Dictyostelium discoideum were studied. DDT, at doses of 60 ppm and above, inhibited growth of the vegetative cells and this was also evident from the colony blots which were smaller in size. A dose-dependent inhibition occurred in the phagocytic activity and macromolecular syntheses of DDT-treated cells. The cytomorphology of growing Dictyostelium cells, as revealed under light and electron microscopes, was profoundly affected by DDT treatment. Further, a considerable delay occurred in the various morphogenetic events in the slime mould cells exposed to DDT.     

Pesticide residue level in tea ecosystems of Hill and Dooars regions of West Bengal, India

In the present study we quantified the residues of organophosphorus (e.g. ethion and chlorpyrifos), organochlorine (e.g. heptachlor, dicofol, alpha-endosulfan, beta-endosulfan, endosulfan sulfate) and synthetic pyrethroid (e.g. cypermethrin and deltamethrin) pesticides in made tea, fresh tea leaves, soils and water bodies from selected tea gardens in the Dooars and Hill regions of West Bengal, India during April and November, 2006. The organophosphorus (OP) pesticide residues were detected in 100% substrate samples of made tea, fresh tea leaves and soil in the Dooars region. In the Hill region, 20% to 40% of the substrate samples contained residues of organophosphorus (OP) pesticides. The organochlorine (OC) pesticide residues were detected in 33% to 100% of the substrate samples, excluding the water bodies in the Dooars region and 0% to 40% in the Hill region. The estimated mean totals of studied pesticides were higher in fresh tea leaves than in made tea and soils. The synthetic pyrethroid (SP) pesticide residues could not be detected in the soils of both the regions and in the water bodies of the Dooars. Sixteen percent and 20% of the made tea samples exceeded the MRL level of chlorpyrifos in Dooars and Hill regions respectively. The residues of heptachlor exceeded the MRL in 33% (April) and 100% (November) in the Dooars and 40% (April) and 20% (November) in the Hill region. Based on the study it was revealed that the residues of banned items like heptachlor and chlorpyrifos in made tea may pose health hazards to the consumers.     

Imperatives for attracting investment and technology in the Indian mining sector

In India, the mineral resource inventory and the production of a large number of important minerals have registered significant increases during the last few decades. Yet the country continues to be a net importer of many high value and scarce minerals and metals, like gold, diamond, and several base metals. Exploration and development of the resources of these minerals are technology- and capital-intensive. To bring technology and capital through foreign direct investment (FDI) into the Indian mineral sector, it is imperative to lay stress on: accurate resource estimation and categorization, as well as realistic projection of the true values; rationalization of legislative measures based on R&D studies and reorganization of the implementation machinery; conducive tax structure; notification of acts and rules applicable to offshore mineral resources; time-frames for granting licences and leases; encouragement to labor productivity by rationalizing labor laws; reforms in the monetary system to increase market competitiveness of Indian minerals; and judicial reforms. FDI in the Indian mineral sector is important to firm up the knowledge-base of mineral resources and their optimum exploitation.     

An application of 3D gasdynamic modeling for the prediction of overpressures in vented enclosures

A three-dimensional gasdynamic model with constant burning rate is applied for the prediction of the maximum pressure rise from gaseous combustion in vented enclosures. A series of calculations for an enclosure with aspect ratio close to unity are presented. Both cases with and without obstacles in the enclosure are considered. Results of calculations are compared with a simple 0D solution for spherical vessels. It is shown that, in cases without obstacles, the 0D solution for the maximum reduced overpressures is close to the predictions of the detailed modeling. In cases with obstacles, the detailed simulation gives significantly higher overpressures than those from the 0D model. However, in all the cases the reduced pressures are correlated well with the maximum flame surface area.