Parameters Influencing Sediments Resuspension and the Link to Sorption of Inorganic Compounds

In the aquatic environment, the accumulation of chemicalcontaminants by sediments poses a potential threat to endemiclife forms and drinking water resources. Trace metals such asCd, Cu, Cr, Ni, Pb, and toxic organic compounds, are among awide variety of contaminants having an affinity for sediments.In this study, experiments were performed simulating sedimentresuspension in the lower Housatonic River, Connecticut, using aParticle Entrainment Simulator. Analyses of grain sizedistributions, porosities and total organic contents of thesediments suggested that these parameters influence theredistribution and entrainment of settleable solids in the watercolumn. These findings were established by evaluating the impactof one parameter on sediment resuspension as a function ofstream flow with the other two characteristics being heldconstant. Total suspended solids and volatile suspended solidsresuspension concentration ranged from 3.2 to 20648.3 mg L^-1,and 1.5 to 1823.8 mg L^-1, respectively, with subsequentincreases in flow rates from 9 to 6 dynes cm^-2. The resuspension concentrations were augmentedby sediment porosity (22.0 to 57.5%), percent finer grain-size distributions at 0.1 mm, and total organic content (2.7 g kg^-1 to 29.0 g kg^-1). Using K _p values, and the dissolvedcontaminant levels of various trace metals, the particulatecontaminant levels of the metals were determined under variousoscillation rates. As sediment resuspension increased withincreased stream flow, there was an overall general increasefrom 0.02 to 33.6 g L^-1 in the particulatecontaminant levels of Cd, Cu, Cr, Ni and Pb.     

Technical feasibility study of a low-cost hybrid PAC-UF system for wastewater reclamation and reuse: a focus on feedwater production for low-pressure boilers

This study has applied the concept of the hybrid PAC-UF process in the treatment of the final effluent of the palm oil industry for reuse as feedwater for low-pressure boilers. In a bench-scale set-up, a low-cost empty fruit bunch-based powdered activated carbon (PAC) was employed for upstream adsorption of biotreated palm oil mill effluent (BPOME) with the process conditions: 60 g/L dose of PAC, 68 min of mixing time and 200 rpm of mixing speed, to reduce the feedwater strength, alleviate probable fouling of the membranes and thus improve the process flux (productivity). Three polyethersulfone ultrafiltration membranes of molecular weight cut-off (MWCO) of 1, 5 and 10 kDa were investigated in a cross-flow filtration mode, and under constant transmembrane pressures of 40, 80, and 120 kPa. The permeate qualities of the hybrid processes were evaluated, and it was found that the integrated process with the 1 kDa MWCO UF membrane yielded the best water quality that falls within the US EPA reuse standard for boiler-feed and cooling water. It was also observed that the permeate quality is fit for extended reuse as process water in the cement, petroleum and coal industries. In addition, the hybrid system’s operation consumed 37.13 Wh m⁻³ of energy at the highest applied pressure of 120 kPa, which is far lesser than the typical energy requirement range (0.8–1.0 kWh m⁻³) for such wastewater reclamation.

     

Wet weather impact on trihalomethane formation potential in tributaries to drinking water reservoirs

During rain storm events, land surface runoff and resuspension of bottom sediments cause an increase in Trihalomethane (THM) precursors in rivers. These precursors, when chlorinated at water treatment facilities will lead to the formation of THMs and hence impact drinking water resources. In order to evaluate the wet weather impact on the potential formation of THMs, river samples were collected before, during and after three rain storms ranging from 15.2 to 24.9 mm precipitation. The samples were tested for THM formation potential and other indicators including UV254 absorbance, turbidity and volatile suspended solid (VSS). Average levels of THMs increased from 61 μg/l during dry weather to 131 μg/l during wet weather, and then went back to 81 μg/l after rain ended. Wet weather values of THM are well above the maximum contaminant level (MCL) 80 μg/l, set by EPA for drinking water. THM indicators also exhibited similar trends. Average levels increased from 0.6 to 1.8 abs; 2.6 to 6 ntu; and 7.5 to 15 mg/l respectively for UV254, turbidity and VSS. A positive correlation was observed between THM formation and THM indicators. The t-test of significance (p-value) was less than 0.05 for all indicators, and R values ranged from 0.85 to 0.92 between THMs and the indicators, and 0.72 to 0.9 among indicators themselves.     

Simulation of arsenic partitioning in tributaries to drinking water resevoirs

Arsenic released by bottom sediments was determined by experiments in which the sediments were artificially re-suspended using a particle entrainment simulator (PES) to simulate river conditions. Sediment cores were collected from various tributaries to drinking water reservoirs in Connecticut spiked with arsenic, and run in the PES at simulated bed-flow shear stresses from 0.0 to 0.6 N/m². Under equilibrium conditions, the dissolved fraction of arsenic was found to range from 8.3 to 22.1 μg/l, which in most cases exceeded EPA Maximum Contaminant Level (MCL) of 10 μg/l. Experimental results from these simulations have shown that bed-flow shear stress causes an increased concentration of dissolved arsenic, most notably at shear stresses of 0.4, 0.5, and 0.6 N/m². For the solid phase under equilibrium, the concentrations of arsenic ranged between 71 and 275 mg/kg. The average concentration of arsenic on the solid phase as well as partitioning coefficient values (K _p) were highest at initial shear stress. This was attributed to the higher fraction of colloidal material and finer organic particles in the suspended solid mixture. Particles of such nature proved to have higher affinity to arsenic. K _p values were determined from PES data and were found to range from 4,687 to 24,090 l/kg. However, on a mass load basis, the amount of arsenic found in suspended sediment increased with the increase of shear stress. Similarly, the amount of arsenic in the solid phase increased significantly for sites with high Volatile Organic Carbon (VOC) content. Because of the influence of Total Suspended Solids (TSS) and VOC concentrations on K _p, the use of the PES is more appropriate in obtaining K _p values that would be found under real stream conditions when compared to the traditional way of measuring K _p using a jar study technique.     

Optimization of activated carbon production from empty fruit bunch fibers in one-step steam pyrolysis for cadmium removal from aqueous solution

The fast growth of the palm oil industry in Malaysia is associated with various waste products, namely the empty fruit bunches (EFB), which have a negative impact on the environment. Therefore, these wastes were utilized as a cheap raw material for the production of activated carbon (AC) with less energy consumption. One-step steam pyrolysis was used to produce AC from oil palm empty fruit bunch fibers (EFBF) by varying the operating parameters of temperature, steam flow rate, and activation time using two-level full factorial experimental design (FFD). Ten samples of AC were prepared and the optimized production conditions were chosen based on the ability to adsorb and remove cadmium. Physical activation comprised of carbonization for 30 min using nitrogen gas (N₂), followed by activation with steam at different flow rates (2.0, 3.0, and 4.0 ml/min), temperatures (600, 750, and 900°C) and times (15, 30, and 45 min). The AC sample produced at an activation temperature of 900°C with a steam flow rate of 2.0 ml/min and activation time of 15 min was selected as the best adsorbent with a total yield of 21.7%. It had adsorbed more than 97% of total cadmium from aqueous solution within 2 min of the contact time. Characterization of EFBF-based AC by SEM and BET surface area analysis had shown a good-quality adsorbent with highly active sites and well-developed pores with BET surface area of 635.16 m²/g. Experimental results indicated that the prepared AC from EFBF provide a promising solution in water and wastewater treatment.     

Parameters affecting partitioning of 6 PCB congeners in natural sediments

Polychlorinated biphenyls (PCBs) released by bottom sediments were determined by experiments in which the sediments were artificially resuspended using sediment contaminated with PCBs in a particle entrainment simulator (PES). Sediment cores, spikedwith PCBs, were collected from the Housatonic River in Connecticut and run in the PES at simulated shear stresses from 0 to 0.6 N m^-2. Experimental results from these simulations have shown that mean concentration of PCBs in thesolid phase for sites with high volatile organic carbon (VOC) were significantly greater than samples with low VOC; the reversewas true for the water phase. In addition, on a mass load basis,the amount of PCBs found in sediment increased when shear stresses were increased from 0 to 0.6 N m^-2, beyond which shear stress did not affect mass loads in the watercolumn. Partition coefficients (K _p) were determined from PESsediment and water data for the following congeners: PCB 28, PCB 52, PCB 101, PCB 138, PCB 153, PCB 180. K _p was determined to be inversely proportional to total suspended solids (TSS), butdirectly proportional to chlorine content of the congener. Because of the strong influence of TSS and VOC concentrations onK _p values, agitation of samples using a PES better simulatedreal environmental conditions when compared to jar studies where no agitation was employed. Therefore, a device like the PES is more appropriate in obtaining K _p that would be found underreal stream flow conditions when compared to the traditionalway of measuring K _p using the jar study technique.