Interinstrument comparison of remote-sensing devices and a new method for calculating on-road nitrogen oxides emissions and validation of vehicle-specific power

Emissions of nitrogen oxides (NOx) by vehicles in real driving environments are only partially understood. This has been brought to the attention of the world with recent revelations of the cheating of the type of approval tests exposed in the dieselgate scandal. Remote-sensing devices offer investigators an opportunity to directly measure in situ real driving emissions of tens of thousands of vehicles. Remote-sensing NO₂ measurements are not as widely available as would be desirable. The aim of this study is to improve the ability of investigators to estimate the NO₂ emissions and to improve the confidence of the total NOx results calculated from standard remote-sensing device (RSD) measurements. The accuracy of the RSD speed and acceleration module was also validated using state-of-the-art onboard global positioning system (GPS) tracking. Two RSDs used in roadside vehicle emissions surveys were tested side by side under off-carriageway conditions away from transient pollution sources to ascertain the consistency of their measurements. The speed correlation was consistent across the range of measurements at 95% confidence and the acceleration correlation was consistent at 95% confidence intervals for all but the most extreme acceleration cases. VSP was consistent at 95% confidence across all measurements except for those at VSP ≥ 15 kW t^?1, which show a small underestimate. The controlled distribution gas nitric oxide measurements follow a normal distribution with 2σ equal to 18.9% of the mean, compared to 15% observed during factory calibration indicative of additional error introduced into the system. Systematic errors of +84 ppm were observed but within the tolerance of the control gas. Interinstrument correlation was performed, with the relationship between the FEAT and the RSD4600 being linear with a gradient of 0.93 and an R² of 0.85, indicating good correlation. A new method to calculate NOx emissions using fractional NO₂ combined with NO measurements made by the RSD4600 was constructed, validated, and shown to be more accurate than previous methods.

Implications: Synchronized remote-sensing measurements of NO were taken using two different remote-sensing devices in an off-road study. It was found that the measurements taken by both instruments were well correlated. Fractional NO₂ measurements from a prior study, measurable on only one device, were used to create new NO_x emission factors for the device that could not be measured by the second device. These estimates were validated against direct measurement of total NO_x emission factors and shown to be an improvement on previous methodologies. Validation of vehicle-specific power was performed with good correlation observed.     

Assessing groundwater quality and its sustainability in Joypurhat district of Bangladesh using GIS and multivariate statistical approaches

Sustainable groundwater quality is a key global concern and has become a major issue of disquiets in most parts of the world including Bangladesh. Hence, the assessment of groundwater quality is an important study to ensure its sustainability for various uses. In this study, a combination of multivariate statistics, geographical information system (GIS) and geochemical approaches was employed to evaluate the groundwater quality and its sustainability in Joypurhat district of Bangladesh. The results showed that the groundwater samples are mainly Ca–Mg–HCO₃ type. Principal component analysis (PCA) results revealed that geogenic sources (rock weathering and cation exchange) followed by anthropogenic activities (domestic sewage and agro-chemicals) were the major factors governing the groundwater quality of the study area. Furthermore, the results of PCA are validated using the cluster analysis and correlation matrix analysis. Based on the groundwater quality index (GWQI), it is found that all the groundwater samples belong to excellent to good water quality domains for human consumption, although iron, fluoride and iodide contaminated to the groundwater, which do not pose any significant health hazard according to World Health Organization’s and Bangladesh’s guideline values. The results of irrigation water quality index including sodium adsorption ratio (SAR), permeability index and sodium percentage (Na %) suggested that most of the groundwater samples are good quality water for agricultural uses. The spatial distribution of the measured values of GWQI, SAR, Fe (iron), EC (electrical conductivity) and TH (total hardness) were spatially mapped using the GIS tool in the study area.     

A synoptic survey of select wastewater-tracer compounds and the pesticide imidacloprid in Florida’s ambient freshwaters

Current wastewater treatment technologies do not remove many unregulated hydrophilic compounds, and there is growing interest that low levels of these compounds, referred to as emerging contaminants, may impact human health and the environment. A probabilistic-designed monitoring network was employed to infer the extent of Florida’s ambient freshwaters containing the wastewater (Includes reuse water, septic systems leachate, and wastewater treatment effluent.) indicators sucralose, acetaminophen, carbamazepine, and primidone and those containing the widely used pesticide imidacloprid. Extent estimates with 95% confidence bounds are provided for canals, rivers, streams, small and large lakes, and unconfined aquifers containing ultra-trace concentrations of these compounds as based on analyses of 2015 sample surveys utilizing 528 sites. Sucralose is estimated to occur in greater than 50% of the canal, river, stream, and large lake resource extents. The pharmaceuticals acetaminophen, carbamazepine, and primidone are most prevalent in rivers, with approximately 30% of river kilometers estimated to contain at least one of these compounds. Imidacloprid is estimated to occur in 50% or greater of the canal and river resource extents, and it is the only compound found to exceed published toxicity or environmental effects standards. Geospatial analyses show sucralose detection frequencies within Florida’s drainage basins to be significantly related to the percentage of urban land use (R²?=?0.36, p?<?0.001), and imidacloprid detection frequencies to be significantly related to the percentage of urban and agricultural land use (R²?=?0.47, p?<?0.001). The extent of the presence of these compounds highlights the need for additional emerging contaminant studies especially those examining effects on aquatic biota.     

Treibhausgasemissionen zukünftiger Erdgasbereitstellung für Deutschland

Ohne Zusammenfassung Original erschienen in UWSF – Z Umweltchem ?kotox 20(2):133–144 (2008) DOI: Herausgeber: Martin Pehnt und Eckard Helmers     

Development of a test method against hot alkaline chemical splashes.

High temperature alkaline chemical liquids have caused injuries and hazardous situations in Finnish pulp manufacturing mills. There are no requirements and/or test method standards concerning protection against high temperature alkaline chemical splashes. This paper describes the test method development process to test and identify materials appropriate for hot liquid chemical hazard protection. In the first phase, the liquid was spilled through a stainless steel funnel and the protection performance was evaluated using a polyvinyl chloride (PVC) film under the test material. After several tentative improvements, a graphite crucible was used for heating and spilling the chemical, and a copper-coated K-type thermometer with 4 independent measuring areas was designed to measure the temperature under the material samples. The thermometer was designed to respond quickly so that peak temperatures could be measured. The main problem was to keep the spilled amount of chemical constant, which unfortunately resulted in significant variability in data.     

Effects of calcium hydroxide and calcium chloride addition to bentonite in iron ore pelletization.

Pyrite ash is created as waste from the roasting of pyrite ores during the production of sulphuric acid. These processes generate great amounts of pyrite ash waste that is generally land filled. This creates serious environmental pollution due to the release of acids and toxic substances. Pyrite ash waste can be utilized in the iron production industry as a blast furnace feed to process this waste and prevent environmental pollution. The essential parameters affecting the pelletization process of pyrite ash were studied using bentonite as a binder. Experiments were then carried out using bentonite and a mixture of bentonite with calcium hydroxide and calcium chloride in order to make the bentonite more effective. The metallurgical properties of pyrite ash, bentonite, calcium hydroxide, calcium chloride, a mixture of these and sintered pellets were studied using X-ray analysis. The crushing strength tests were carried out to investigate the strength of pyrite ash waste pellets. The results of these analyses showed that pyrite ash can be agglomerated to pellets and used in the iron production industry as a blast furnace feed. The crushing strength of the pellets containing calcium hydroxide and calcium chloride in addition to bentonite was better than the strength of pellets prepared using only bentonite binder.     

Working backwards to move forwards: Graph-based connectivity metrics for reserve network selection

In this paper we apply graph theory in a reserve selection exercise to explore the tradeoffs between maintaining connectivity and minimizing the total area of a protected area network. Rather than focus on a single organism, we used a multi-species approach and looked at the tradeoff curves for organisms with varying dispersal abilities. We first generated the tradeoff curves using a graph-based metric to determine the importance of individual patches for maintaining connectivity. We then performed an analogous set of analyses using patch size as a surrogate measure of importance.