Fungicidal values of bio-oils and their lignin-rich fractions obtained from wood/bark fast pyrolysis

Pine wood, pine bark, oak wood and oak bark were pyrolyzed in an auger reactor. A total of 16 bio-oils or pyrolytic oils were generated at different temperatures and residence times. Two additional pine bio-oils were produced at the National Renewable Energy Laboratory in a fluidized-bed reactor at different temperatures. All these bio-oils were fractionated to obtain lignin-rich fractions which consist mainly of phenols and neutrals. The pyrolytic lignin-rich fractions were obtained by liquid-liquid extraction. Whole bio-oils and their lignin-rich fractions were studied as potential environmentally benign wood preservatives to replace metal-based CCA and copper systems that have raised environmental concerns. Each bio-oil and several lignin-rich fractions were tested for antifungal properties. Soil block tests were conducted using one brown-rot fungus (Gloeophyllum trabeum) and one white-rot fungus (Trametes versicolor). The lignin-rich fractions showed greater fungal inhibition than whole bio-oils for a impregnation solution 10% concentration level. Water repellence tests were also performed to study wood wafer swelling behavior before and after bio-oil and lignin-rich fraction treatments. In this case, bio-oil fractions did not exhibit higher water repellency than whole bio-oils. Comparison of raw bio-oils in soil block tests, with unleached wafers, at 10% and 25% bio-oil impregnation solution concentration levels showed excellent wood preservation properties at the 25% level. The good performance of raw bio-oils at higher loading levels suggests that fractionation to generate lignin-rich fractions is unnecessary. At this more effective 25% loading level in general, the raw bio-oils performed similarly. Prevention of leaching is critically important for both raw bio-oils and their fractions to provide decay resistance. Initial tests of a polymerization chemical to prevent leaching showed some success.     

Insights into aqueous carbofuran removal by modified and non-modified rice husk biochars

Biochar has been considered as a potential sorbent for removal of frequently detected pesticides in water. In the present study, modified and non-modified rice husk biochars were used for aqueous carbofuran removal. Rice husk biochars were produced at 300, 500, and 700 °C in slow pyrolysis and further exposed to steam activation. Biochars were physicochemically characterized using proximate, ultimate, FTIR methods and used to examine equilibrium and dynamic adsorption of carbofuran. Increasing pyrolysis temperature led to a decrease of biochar yield and increase of porosity, surface area, and adsorption capacities which were further enhanced by steam activation. Carbofuran adsorption was pH-dependant, and the maximum (161 mg g^?1) occurred in the vicinity of pH 5, on steam-activated biochar produced at 700 °C. Freundlich model best fitted the sorption equilibrium data. Both chemisorption and physisorption interactions on heterogeneous adsorbent surface may involve in carbofuran adsorption. Langmuir kinetics could be applied to describe carbofuran adsorption in a fixed bed. A higher carbofuran volume was treated in a column bed by a steam-activated biochar versus non-activated biochars. Overall, steam-activated rice husk biochar can be highlighted as a promising low-cost sustainable material for aqueous carbofuran removal.     

Case study of landfill leachate recirculation using small-diameter vertical wells

A case study of landfill liquids addition using small diameter (5 cm) vertical wells is reported. More than 25,000 m³ of leachate was added via 134 vertical wells installed 3 m, 12 m, and 18 m deep over five years in a landfill in Florida, US. Liquids addition performance (flow rate per unit screen length per unit liquid head) ranged from 5.6 × 10^?8 to 3.6 × 10^?6 m³ s^?1 per m screen length per m liquid head. The estimated radial hydraulic conductivity ranged from 3.5 × 10^?6 to 4.2 × 10^?4 m s^?1. The extent of lateral moisture movement ranged from 8 to 10 m based on the responses of moisture sensors installed around vertical well clusters, and surface seeps were found to limit the achievable liquids addition rates, despite the use of concrete collars under a pressurized liquids addition scenario. The average moisture content before (51 samples) and after (272 samples) the recirculation experiments were 23% (wet weight basis) and 45% (wet weight basis), respectively, and biochemical methane potential measurements of excavated waste indicated significant (p < 0.025) decomposition.     

Developing an effectiveness index for biomedical waste management in Indian states using a composite indicators approach

Environmental Science and Pollution Research - The waste from healthcare facilities (HCFs) is most devastating as they induce health hazards and pollute the environment. The effective management of...     

Environmental radon studies using solid state nuclear track detectors

The results of radon activity recorded in 70 dwellings of Nurpur area, Kangra district, Himachal Pradesh, India are reported. LR-115 Type 2 films in the bare mode were exposed for four seasons of three months each covering a period of one year for the measurement of indoor radon levels. The calibration constant of 0.020 tracks cm(-2) d(-1) per Bq m(-3) has been used to express radon activity in Bq m(-3). The annual average indoor radon concentrations in 17 different villages of the area are found to vary from 168+/-46 to 429+/-71. Most of the indoor radon values lie in the range of action levels (200-600 Bq m(-3)) recommended by International Commission on Radiological Protection.     

Field evaluation of resistivity sensors for in situ moisture measurement in a bioreactor landfill

The ability of resistance-based sensors to measure in situ waste moisture content in a landfill was examined. One hundred and thirty-five resistance-based sensors were installed in a leachate recirculation well field at a bioreactor landfill in Florida, US. The performance of these sensors was studied for a period of over 6 years. The sensors were found to respond to an increase in moisture resulting from leachate recirculation. It was observed that 78% of sensors worked successfully in the field during the study period. The initial spatial average moisture content determined by the sensor readings (using a laboratory-derived calibration) was 42.8% compared to 23% from gravimetric readings. Eighteen sensors (13%) showed that they were saturated before liquid addition, and no change in moisture content was observed in these sensors during the study period. Laboratory-derived calibration methods resulted in an over-estimation of moisture content. An alternate field-calibration method, where wetted sensor output was assumed equal to the average of gravimetric measurements for wet samples, was evaluated. The final spatial average moisture contents were 64.2% and 44.4% for the laboratory-derived and field-derived calibration methodologies, respectively, compared to 45% measured gravimetrically from excavated waste samples. When moisture content was determined using a mass balance approach, the result was 34.6%. The results suggest that when appropriately calibrated, resistivity-based sensors can be used to obtain a reasonably accurate estimate of local moisture content. However, caution should be taken to extend the moisture content values that are representative of waste surrounding the sensors to estimate the overall moisture content on the landfill-wide scale.     

Formulation of a landfill pollution potential index to compare pollution potential of uncontrolled landfills

Generally speaking, landfilling is one of the prominent methods of waste disposal around the globe, but some under-developed and developing countries still continue to practice uncontrolled open dumping of waste. These uncontrolled landfills pose a relatively high threat to the various elements of the environment in comparison with the conventional engineered landfills that are used in many developed countries. However, some closed, un-engineered landfills do exist in developing countries. This paper presents a novel approach to compare the pollution potential of uncontrolled landfills using an index. The landfill pollution potential index (LPPI) has been developed using the Delphi technique and is an aggregation of six pollution indices that have already been developed for the quantification of different environmental elements. The LPPI is an increasing scale index, in which a higher index value indicates a higher pollution threat. The LPPI of a landfill in Delhi was calculated and the high LPPI value indicates that the respective landfill poses a significant threat to the environment. The LPPI can be used as an aid to diagnose a landfill's pollution potential relative to other landfills and therefore also to rank remediation investments.     

Emissions from RDF/coal blended fuel combustion

The significant volume and weight reduction along with the energy potential of MSW, in the form of refuse derived fuel (RDF), has made its incineration an attractive alternative. However, the gaseous emissions such as, CO₂, CO, NO_x and SO₂, which are the byproduct of the combustion process pose serious environmental problems. These problems are compounded by the presence of certain highly regulated hazardous wastes such as, dioxins and furans in the exhaust stream. In the present investigation, different compositions of RDF/Coal blends were examined and the gaseous emissions from the combustion of the briquetted fuel were measured. Also, a direct comparison of emissions from RDF/coal blend incineration with coal combustion is presented in this paper. The potential for recovery of ferrous and non- ferrous metals provides an additional economic motivation for the use of RDF/Coal blended briquettes.     

Green energy generation through PEHF – a blueprint of alternate energy harvesting

In this work, an attempt has been made to harvest green energy from piezoelectric material using fluid flow in a conduit. Piezoelectric Energy Harvesting using Fluid Flow (PEHF) experimental model has been designed and the outputs obtained are compared with results obtained from simulations using ANSYS (computational fluid dynamics) and also with the mathematical modeling. The PEHF model has been utilized to analyze the effect of flow rate of water with reference to energy extracted. The full wave bridge rectifier and voltage doubler circuits have been used to obtain the direct current (DC) from the PEHF model. It is observed that the output obtained using experiments holds good in agreement with the results retrieved through simulations and mathematical results. The increase in flow rate of fluid leads to initially increase and then decrease in output of PEHF model as the maximum energy generated when flow rates (external force) matches with the frequency of excitation of the systems, i.e., at its resonance. The maximum energy output is generated at its resonance frequencies. It is observed that the full wave bridge rectifier circuit gives greater output as compared to a voltage doubler circuit.     

Impact assessment of treated/untreated wastewater toxicants discharged by sewage treatment plants on health, agricultural, and environmental quality in the wastewater disposal area

Studies were undertaken to assess the impact of wastewater/sludge disposal (metals and pesticides) from sewage treatment plants (STPs) in Jajmau, Kanpur (5 MLD) and Dinapur, Varanasi (80 MLD), on health, agriculture and environmental quality in the receiving/application areas around Kanpur and Varanasi in Uttar Pradesh, India. The raw, treated and mixed treated urban wastewater samples were collected from the inlet and outlet points of the plants during peak (morning and evening) and non-peak (noon) hours. The impact of the treated wastewater toxicants (metals and pesticides) on the environmental quality of the disposal area was assessed in terms of their levels in different media samples viz., water, soil, crops, vegetation, and food grains. The data generated show elevated levels of metals and pesticides in all the environmental media, suggesting a definite adverse impact on the environmental quality of the disposal area. The critical levels of the heavy metals in the soil for agricultural crops are found to be much higher than those observed in the study areas receiving no effluents. The sludge from the STPs has both positive and negative impacts on agriculture as it is loaded with high levels of toxic heavy metals and pesticides, but also enriched with several useful ingredients such as N, P, and K providing fertilizer values. The sludge studied had cadmium, chromium and nickel levels above tolerable levels as prescribed for agricultural and lands application. Bio-monitoring of the metals and pesticides levels in the human blood and urine of the different population groups under study areas was undertaken. All the different approaches indicated a considerable risk and impact of heavy metals and pesticides on human health in the exposed areas receiving the wastewater from the STPs.