Fluoride deposition in snow in the surroundings of a mixed fertilizer factory

The fluoride content of snow was determined at various distances from a mixed fertilizer factory in Siilinjärvi, central Finland. Elevated fluoride levels were observed at less than 2 km from the factory, and the highest concentrations close to the factory were about 600 μg of fluoride per liter of melt water. At unpolluted reference sites the fluoride content was about 6μg/1. The background level of fluoride in precipitation is discussed. An ion selective electrode and a simple calibration method were used in the analyses.     

Chlorophenols in lake bottom sediments: A retrospective study of drinking water contamination

Lake and brook bottom sediments were analyzed for chlorophenols to provide historical data of exposure assessment, after the water intake plant of a Finnish village had been found to be contaminated in 1987, and subsequently elevated non-Hodgkin lymphoma risk was detected. Highly elevated 2,3,4,6-tetrachlorophenol and pentachlorophenol levels were found in all four lake sediment cores investigated. The distribution was uneven with much higher concentrations in the estuary, in contrast to PCB compounds which were more evenly distributed within the basin. The inlet origin of the chlorophenols in the sediments was further supported by the regional distribution pattern of these compounds in the sediment and water along transects of the inlet and its tributaries. The composition of chlorophenol congeners in the sediments was similar to that in a commercial fungicide used by a local sawmill, but different from other sediment analyses reported in Finland, also implying a local source. Dating of three cores by Pb-210 and soot ball chronology indicated that the contamination of the watercourse started in the early 1970s at the latest but possibly earlier. This would provide the latency time required for tumour appearance in the 1970s and 1980s.     

Phosphorus loss from different farming systems estimated from soil surface phosphorus balance

The phosphorus load originating from crop production and animal husbandry is a major contributor to the eutrophication of lakes, rivers and coastal waters. The P losses to surface waters may, however, differ drastically due to the diversity of agricultural production systems practised under contrasting environmental conditions. To assess the most problematic types of agriculture, we need information on the P load from different alternative farming practices. Such information cannot, however, be obtained solely from field runoff experiments, as the number of treatment combinations required to account for all relevant farming systems and environmental conditions far exceeds our research capabilities. To facilitate the comparison of P loads, we therefore need reasonably simple models. A key factor controlling the P load from agriculture is the past and present use of nutrients in fertilizers and manure in relation to a crop's uptake, i.e. the soil-surface balance of P. Here, we present a simple empirical model that relates the P surplus (or deficit) in a farm to the edge-of-field losses of algal-available P. Based on long-term fertilizer trials, the model first estimates the change in soil-test P of top soil with the aid of the soil-surface balance of P. Soil-test P is then used to approximate the concentration of dissolved reactive P in surface runoff and drainage flow, as adjusted for different P application types. The loss of particulate P is obtained from typical erosion rates. The model can be applied in life-cycle analyses and in assessing future developments. We illustrate use of the model by calculating the loss of algal-available P from conventional and organic crop and dairy farms located on clay and fine sand soils.     

Aerosol Particle Number Concentration Measurements in Five European Cities Using TSI-3022 Condensation Particle Counter over a Three-Year Period during Health Effects of Air Pollution on Susceptible Subpopulations

Abstract

In this study, long-term aerosol particle total number concentration measurements in five metropolitan areas across Europe are presented. The measurements have been carried out in Augsburg, Barcelona, Helsinki, Rome, and Stockholm using the same instrument, a condensation particle counter (TSI model 3022). The results show that in all of the studied cities, the winter concentrations are higher than the summer concentrations. In Helsinki and in Stockholm, winter concentrations are higher by a factor of two and in Augsburg almost by a factor of three compared with summer months. The winter maximum of the monthly average concentrations in these cities is between 10,000 cm^-3 and 20,000 cm^-3, whereas the summer min is ?;5000–6000 cm^-3. In Rome and in Barcelona, the winters are more polluted compared with summers by as much as a factor of 4–10. The winter maximum in both Rome and Barcelona is close to 100,000 cm^-3, whereas the summer minimum is >10,000 cm^-3. During the weekdays the maximum of the hourly average concentrations in all of the cities is detected during the morning hours between 7 and 10 a.m. The evening maxima were present in Barcelona, Rome, and Augsburg, but these were not as pronounced as the morning ones. The daily maxima in Helsinki and Stockholm are close or even lower than the daily minima in the more polluted cities. The concentrations between these two groups of cities are different with a factor of about five during the whole day. The study pointed out the influence of the selection of the measurement site and the configuration of the sampling line on the observed concentrations.     

Comparison of VOC emissions between air-dried and heat-treated Norway spruce (Picea abies), Scots pine (Pinus sylvesteris) and European aspen (Populus tremula) wood

Heat-treated wood is an increasingly popular decoration material. Heat-treatment improves dimensional stability of the wood and also prevents rot fungus growth. Although production of heat-treated wood has been rapidly increasing, there is only little information about the VOC emissions of heat-treated wood and its possible influences on indoor air quality. In the present study, VOC emissions from three untreated (air-dried) and heat-treated wood species were compared during a four weeks test period. It appeared that different wood species had clearly different VOC emission profiles. Heat-treatment was found to decrease VOC emissions significantly and change their composition. Especially, emissions of terpenes decreased from softwood samples and aldehydes from European aspen samples. Emissions of total aldehydes and organic acids were at the same level or slightly higher from heat treated than air-dried softwood samples. In agreement with another recent study, the emissions of furfural were found to increase and those of hexanal to decrease from all the wood species investigated. In contrast to air-dried wood samples, emissions of VOCs were almost in steady state from heat treated wood samples even in the beginning of the test.     

A proposal for a long-term baseline phytobenthos monitoring programme for the Finnish Baltic coastal waters: monitoring submerged rocky shore vegetation

Several local surveys on the submerged vegetation have been conducted in past decades along the Finnish Baltic coastal areas. Surveys have been carried out by using various methods,which make the temporal comparisons of the results difficult.The need of a joint programme for coastal phytobenthic monitoringis emphasised by the Nordic Council of Ministers and HELCOM. TheFinnish coastal phytobenthic monitoring programme complements theBaltic HELCOM monitoring programme (COMBINE). It is primarily designed to reveal the effects of eutrophication. The programmeincludes general principles for selection of monitoring areas aswell as a proposal for monitored habitats, communities and species. The need of evaluated and tested field methods, datacollecting, interpretation and data storage are addressed in theQuality Assurance part. The cost-efficiency is secured by integrating the phytobenthos programme with the coastal water monitoring for obtaining the supporting data such like salinity,temperature and nutrients. In the design of the monitoring programme a special interest is paid on areas with high protection values such as Natura 2000 or HELCOM's BSPA (Baltic Sea Protected Areas) or on aspects that would support the implementation of the EU Water Framework Directive.     

Low-flow active and passive sampling of VOCs using thermal desorption tubes: theory and application at an offset printing facility

While air sampling techniques using adsorbent-based collection, thermal desorption and chromatographic analysis have found a niche in ambient air sampling, occupational applications have been more limited. This paper evaluates the use of thermal desorption techniques for low flow active and passive sampling configurations which allow conveniently long duration sampling in occupational settings and other high concentration environments. The use of an orifice enables flows as low as 0.5 ml min(-1) and sampling periods up to several days without significant biases. A model is used to predict sampling rates of a passive sampler encompassing an orifice, a void space, glass wool, and the adsorbent. Laboratory and field tests conducted at a commercial offset printing facility, which contained a variety of volatile organic compounds (primarily aromatic but also a few chlorinated and terpene compounds at levels from 1 to 67,000 microg m(-3)), are used to evaluate the approach. Tenax GR and Carbosieve SIII, both singly and together, were employed as adsorbents. Side-by-side tests comparing high flow, low flow and passive samplers show excellent agreement and high linearity (r = 0.95) for concentrations spanning nearly five orders of magnitude. Active samplers were tested at flows as low as 0.5 ml min(-1), compared to typical flows up to 40 ml min(-1). Passive samplers demonstrated a linear range and agreement with predictions for adsorbate loadings from approximately 1 ng to nearly 10 microg. Using a chemical mass balance receptor model, concentrations in the facility were apportioned to solvents, inks and other indoor and outdoor sources. Overall, the use of low flow active and passive sampling approaches employing thermal desorption techniques provides good performance and tremendous flexibility that facilitates use in many applications, including workplace settings.     

Aerosol particle number concentration measurements in five European cities using TSI-3022 condensation particle counter over a three-year period during health effects of air pollution on susceptible subpopulations

In this study, long-term aerosol particle total number concentration measurements in five metropolitan areas across Europe are presented. The measurements have been carried out in Augsburg, Barcelona, Helsinki, Rome, and Stockholm using the same instrument, a condensation particle counter (TSI model 3022). The results show that in all of the studied cities, the winter concentrations are higher than the summer concentrations. In Helsinki and in Stockholm, winter concentrations are higher by a factor of two and in Augsburg almost by a factor of three compared with summer months. The winter maximum of the monthly average concentrations in these cities is between 10,000 cm(-3) and 20,000 cm(-3), whereas the summer min is approximately 5000-6000 cm(-3). In Rome and in Barcelona, the winters are more polluted compared with summers by as much as a factor of 4-10. The winter maximum in both Rome and Barcelona is close to 100,000 cm(-3), whereas the summer minimum is > 10,000 cm(-3). During the weekdays the maximum of the hourly average concentrations in all of the cities is detected during the morning hours between 7 and 10 a.m. The evening maxima were present in Barcelona, Rome, and Augsburg, but these were not as pronounced as the morning ones. The daily maxima in Helsinki and Stockholm are close or even lower than the daily minima in the more polluted cities. The concentrations between these two groups of cities are different with a factor of about five during the whole day. The study pointed out the influence of the selection of the measurement site and the configuration of the sampling line on the observed concentrations.     

Diffusive uptake in passive and active adsorbent sampling using thermal desorption tubes

Low flow active sampling techniques collecting vapors and gases using thermally desorbable adsorbents are now feasible and desirable in many applications as they permit long integration times, the potential for miniaturized sampling configurations, and other advantages. At very low air flow rates (< 1 ml min(-1)), diffusive uptake on adsorbents in conventional sorbent tubes may equal or exceed the active (pumped) uptake rate, and even at low flow rates (1-4 ml min(-1)), diffusive uptake may significantly bias measurements. Thus, corrections to account for the diffusive flux or means to limit the diffusive uptake are needed in low flow applications. This paper presents (1) a theoretical analysis of the role of diffusive and advective uptake for several sampling geometries of tube-type samplers; (2) experimental confirmation using both laboratory and field studies; (3) estimates of the tortuosity and porosity of the glass wool packing used to retain the adsorbent, parameters needed to estimate diffusive fluxes in passive and active sampling; (4) a demonstration that orifice-equipped low flow active samplers can reduce diffusive uptake and improve precision, and (5) a model predicting the saturated adsorbent layer that helps to account for the gradual decline in uptake rates seen in passive sampling. Diffusive uptake will depend on the tube configuration and diffusion coefficient of the substance of interest, but for conventional sampling tubes (0.4-0.5 cm id, 1.5 cm air gap), sample flow rates should be maintained above 1 to 4 ml min(-1) to keep errors below 5%. Laboratory experiments showed close agreement with theoretical calculations, and the field study using 1 to 4 d sampling periods and 0.3 ml min(-1) flows demonstrated that the orifice-equipped samplers essentially eliminated diffusive uptake. No significant practical difficulties are encountered using orifices, e.g., pressure drop is minimal. Experimental estimates of tortuosity (0.79 +/- 0.02) and porosity (0.92 +/- 0.10) of the glass wool packing (0.3 cm length) represent relatively little resistance to diffusion; however, variation in the packing and adsorbent placement can degrade the precision achievable by passive samplers. Diffusion barriers, consisting most simply of an orifice, may be used to lower the diffusive uptake. A needle-type orifice permits flows below 0.1 ml min(-1) and is suitable for sampling periods as long as several weeks, and it provided greater precision than conventional open-ended sampling tubes (8% compared to 13%). Finally, the gradual decrease in diffusive fluxes often seen in passive sampling is attributed to additional resistance posed by a saturated adsorbent layer, in agreement with a simple model based on total VOCs and specific adsorptivity of the adsorbent.