Investigations of ash fouling with cattle wastes as reburn fuel in a small-scale boiler burner under transient conditions

Fouling behavior under reburn conditions was investigated with cattle wastes (termed as feedlot biomass [FB]) and coal as reburn fuels under a transient condition and short-time operation. A small-scale (30 kW or 100,000 Btu/hr) boiler burner research facility was used for the reburn experiments. The fuels considered for these experiments were natural gas (NG) for the ashless case, pure coal, pure FB, and blends of coal and FB. Two parameters that were used to characterize the ash "fouling" were (1) the overall heat-transfer coefficient (OHTC) when burning NG and solid fuels as reburn fuels, and (2) the combustible loss through ash deposited on the surfaces of heat exchanger tubes and the bottom ash in the ash port. A new methodology is presented for determining ash-fouling behavior under transient conditions. Results on the OHTCs for solid reburn fuels are compared with the OHTCs for NG. It was found that the growth of the layer of ash depositions over longer periods typically lowers OHTC, and the increased concentration of ash in gas phase promotes radiation in high-temperature zones during initial periods while decreasing the heat transfer in low-temperature zones. The ash analyses indicated that the bottom ash in the ash port contained a smaller percentage of combustibles with a higher FB percentage in the fuels, indicating better performance compared with coal because small particles in FB burn faster and the FB has higher volatile matter on a dry ash-free basis promoting more burn out.     

Pesticide residue level in tea ecosystems of Hill and Dooars regions of West Bengal, India

In the present study we quantified the residues of organophosphorus (e.g. ethion and chlorpyrifos), organochlorine (e.g. heptachlor, dicofol, alpha-endosulfan, beta-endosulfan, endosulfan sulfate) and synthetic pyrethroid (e.g. cypermethrin and deltamethrin) pesticides in made tea, fresh tea leaves, soils and water bodies from selected tea gardens in the Dooars and Hill regions of West Bengal, India during April and November, 2006. The organophosphorus (OP) pesticide residues were detected in 100% substrate samples of made tea, fresh tea leaves and soil in the Dooars region. In the Hill region, 20% to 40% of the substrate samples contained residues of organophosphorus (OP) pesticides. The organochlorine (OC) pesticide residues were detected in 33% to 100% of the substrate samples, excluding the water bodies in the Dooars region and 0% to 40% in the Hill region. The estimated mean totals of studied pesticides were higher in fresh tea leaves than in made tea and soils. The synthetic pyrethroid (SP) pesticide residues could not be detected in the soils of both the regions and in the water bodies of the Dooars. Sixteen percent and 20% of the made tea samples exceeded the MRL level of chlorpyrifos in Dooars and Hill regions respectively. The residues of heptachlor exceeded the MRL in 33% (April) and 100% (November) in the Dooars and 40% (April) and 20% (November) in the Hill region. Based on the study it was revealed that the residues of banned items like heptachlor and chlorpyrifos in made tea may pose health hazards to the consumers.     

Study of the performance of a coolant mixed with an Al2O3/SiC nanomaterial in an engine radiator

One of the important components of a car to control the temperature of a car's engine is the radiator. To increase the heat absorption capacity of the coolant/fluid used in the radiator with minimum pumping power, innovative fluids called nanofluids have become the main area of research these days. Therefore, with the development of new technologies in the field of “nano-materials” and “nano-fluids,” the physical and chemical properties of coolant/fluid can be improved which in turn improves the radiator and engine efficiency, and reduces radiator weight and size. In this article, the heat transfer by forced convection in nanofluids based on Al₂O₃ and SiC was studied experimentally and compared to that of base fluid in an automotive radiator. The nanofluid is mixed with ethylene glycol and the fluid is prepared by the sonication method. The nanofluids were prepared by varying the nanomaterials and the amounts of nanomaterials in the base fluid and their heat transfer performance in the radiator was analyzed using ANSYS FLUENT software. Approximately 15% and 12% increase in radiator efficiency by using Al₂O₃ mixed nanofluid and SiC mixed nanofluid, respectively.     

Updraft gasification of juniper wood biomass using CO2–O2 and Air (N2–O2)

Biomass gasification is being considered as one of the most promising technologies for converting low-quality solid biomass fuel into gaseous fuel. Redberry juniper (Juniperus pinchotii), one of the woody species that dominate uncultivated lands in the southern great plains, USA, may have a great potential for bioenergy utilization. In this study, the results of gasification of juniper are presented. Juniper wood chips were gasified in an adiabatic fixed bed updraft gasifier using air and the mixture gas of carbon dioxide and oxygen (CO₂:O₂) as gasification medium. The effect of gasification parameters such as moisture contents, gasification mediums, and gasification temperature on produced gas properties and the tar yield were investigated. It was observed that oxy fuel gasification (the reaction of woody fuels with carbon dioxide) of juniper resulted in the increase of production of carbon monoxide, especially at higher peak gasification temperatures. As a result, the CO₂ gasification resulted in producing higher heating value gas (6264 kJ/nm³ with dilution of CO₂ and 19,750 kJ/nm³ inert free) compared to air gasification. For air gasification, it was observed that the updraft gasification produced large amount of the tar in the product gas (more than 100 g/nm³) for the fuels with moisture content between 6% and 11%. Generally, the tar yield increased with the increase of equivalence ratio (er) and moisture content. However, when the fuel moisture content reached 23.5%, the tar yield reduced significantly due low gasification temperature which reduced the less tar cracking.     

Estimating the Recreation Demand and Economic Value of Mountain Biking in Moab,Utah: An Application of Count Data Models

This paper reports the results of both standard and truncated count data travel cost demand models for estimating demand for and the economic value to participants in mountain biking in the Moab, Utah, area. The empirical estimates for average trip demand per person per season were 2.25 and 2.53 trips under truncated Poisson and truncated negative binomial models, respectively. Consumer surplus per person per trip for both models was approximately US $585. The total annual use value for mountain biking in the Moab area was US $1.33 million. This value suggests that this recreation has a higher value than most other activities in the area and that public land managers should be aware of the relative value of mountain biking as they make allocation decisions.     

Fractionation and bioavailability of metals and their impacts on microbial properties in sewage irrigated soil

A study was conducted to evaluate the effect of long-term irrigation of sewage contaminated with heavy metals like Cd, Cr, Cu and Pb on microbial and biochemical parameters of soils of West Bengal, India. The microbial parameters included microbial biomass carbon (MBC), microbial metabolic quotient; the biochemical parameters included fluorescein diacetate hydrolyzing activity, beta-glucosidase, urease, phosphatase, and aryl sulphatase activities. A sequential extraction technique was used to quantify water soluble, exchangeable, carbonate bound, Fe/Mn-oxide bound, organically bound, and residual metal fractions. Metal concentrations in the two most labile fractions (i.e., water soluble and exchangeable fractions) were generally low. Total metal concentrations at each site seemed to be associated with soil amorphous Fe and Al minerals. The MBC and the enzymes studied were significantly and negatively correlated with water soluble and exchangeable metals but not significantly correlated with other forms, indicating that water soluble and exchangeable forms exerted a strong inhibitory effect on the soil microbial and biochemical parameters. It was concluded that irrigating soils with metal contaminated sewage seemed to damage soil quality in the long term.     

Turbulent secondary flows in wall turbulence: vortex forcing,scaling arguments,and similarity solution

Spanwise surface heterogeneity beneath high-Reynolds number, fully-rough wall turbulence is known to induce a mean secondary flow in the form of counter-rotating streamwise vortices—this arrangement is prevalent, for example, in open-channel flows relevant to hydraulic engineering. These counter-rotating vortices flank regions of predominant excess(deficit) in mean streamwise velocity and downwelling(upwelling) in mean vertical velocity. The secondary flows have been definitively attributed to the lower surface conditions, and are now known to be a manifestation of Prandtl’s secondary flow of the second kind—driven and sustained by spatial heterogeneity of components of the turbulent (Reynolds averaged) stress tensor (Anderson et al. J Fluid Mech 768:316–347, 2015). The spacing between adjacent surface heterogeneities serves as a control on the spatial extent of the counter-rotating cells, while their intensity is controlled by the spanwise gradient in imposed drag (where larger gradients associated with more dramatic transitions in roughness induce stronger cells). In this work, we have performed an order of magnitude analysis of the mean (Reynolds averaged) transport equation for streamwise vorticity, which has revealed the scaling dependence of streamwise circulation intensity upon characteristics of the problem. The scaling arguments are supported by a recent numerical parametric study on the effect of spacing. Then, we demonstrate that mean streamwise velocity can be predicted a priori via a similarity solution to the mean streamwise vorticity transport equation. A vortex forcing term has been used to represent the effects of spanwise topographic heterogeneity within the flow. Efficacy of the vortex forcing term was established with a series of large-eddy simulation cases wherein vortex forcing model parameters were altered to capture different values of spanwise spacing, all of which demonstrate that the model can impose the effects of spanwise topographic heterogeneity (absent the need to actually model roughness elements); these results also justify use of the vortex forcing model in the similarity solution.     

Improving the dynamic response of frequency and power in a wind integrated power system by optimal design of compensated superconducting magnetic energy storage

The frequency deviation and power fluctuation need to be controlled in a wind-integrated power system (WIPS) for keeping the balance between system power generation and demand, which support the quality and stability of overall power system. The present paper addresses this problem while concerning the integration of intermittent wind power and load disturbance into the WIPS. With this intent, it proposes the compensated superconducting magnetic energy storage (CSMES) system with proportional integral derivative (PID) controller for improving the frequency and power deviation profile. A novel swarm intelligence-based artificial bee colony (ABC) algorithm is used for optimal design of PID-CSMES system. Robustness of the proposed ABC-based PID-CSMES control strategy is tested in WIPS under various disturbance patterns of load and wind power. To demonstrate the improved dynamic response, their simulation results are compared with particle swarm optimization-based PID-CSMES, PID with SMES, and only PID controller technique. The performance indices and transient response characteristics of frequency and power deviation are used to evaluate and compare the accuracy and efficiency of each controller. Stability of various system configurations is analyzed using eigenvalue location. Comparing the results of different controller in WIPS indicates a substantial improvement in the dynamic response of system frequency and power deviations by utilizing the proposed control strategy.