火力发电企业排污自行监测质量提升

针对目前火力发电企业排污自行监测过程中存在的质量管理体系不完善、手工监测能力不足、对外委监测机构监督环节薄弱等突出问题,从质量管理体系建设、质量控制机制建立、第三方检测机构选择及智能化手段应用四个方面提出火力发电企业排污自行监测质量提升改进建议,为自行监测数据结果的科学性、准确性提供可靠的质量保证。     

Heat dissipation characteristic in the intake grille and radiator of a fuel cell vehicle

ABSTRACT

In this study, a three-dimension (3D) computational model was proposed to investigate the flow and heat transfer characteristics of the intake grilles of two different fuel cell vehicles. The models of the intake grilles were constructed according to the actual sizes of two vehicles, namely, Roewe 950 and Toyota Mirai, considering the heat dissipation unit to simplify the heat transfer model of the vehicle. The results showed that relative to Roewe 950, Mirai intake air flow rate was approximately 10% higher, the heat transfer capacity was approximately 7% higher, and the intake grille area was larger. The coolant outlet temperature of Mirai was lower than that of Roewe 950, which was beneficial for the long term and stable operation of a fuel cell. This comparative study provided guidance for the intake grille and radiator design of fuel cell vehicles. The only difference between fuel cell vehicles on the market and conventional vehicles was that in the former, the internal combustion engine was replaced with a fuel cell stack, which had insufficient heat transfer capacity because of the reducing temperature difference. Increasing the intake grille area and the heat exchange capacity of the radiator were the key issues for the development of fuel cell vehicles. In this study, an optimal window opening angle of the radiator fin of 23° provided a maximal heat transfer coefficient.     

高氯酸盐还原颗粒污泥的快速培养及其特性分析

为实现高氯酸盐还原颗粒污泥的快速培养,以反硝化颗粒污泥为接种污泥,对高氯酸盐还原颗粒污泥的快速培养进行了研究。在降低进水硝酸盐(NO_3~-)浓度的同时,采用逐步升高进水高氯酸盐(ClO_4~-)浓度的方法,考察了高氯酸盐还原颗粒污泥培养过程中ClO_4~-的去除以及颗粒污泥的特性。结果表明:以反硝化颗粒污泥为接种污泥,经过50 d快速培养出高氯酸盐还原颗粒污泥,ClO_4~-去除速率达96%以上;其混合液悬浮固体浓度(MLSS)为50.68 g·L~(-1),混合液挥发性固体浓度(MLVSS)为40.58 g·L~(-1),主要粒径分布在0.60 mm和1.00～2.00 mm。NO_3~-浓度逐步降低的培养方式可缓解ClO_4~-对颗粒污泥中各类微生物的毒性,为高氯酸盐颗粒污泥的快速培养提供了新的方法,具有重要的理论和实践意义。     

“两带”渗透率分布模型应用及渗透率规律研究*

为了研究覆岩破坏后形成“两带”的渗透率分布规律,根据理论推导应力-应变曲线以及采空区材料力学参数公式,建立“两带”渗透率分布模型,采用COMSOL软件分别对垮落带的渗透率分布和断裂带渗透率分布进行数值模拟。研究结果表明:垮落带渗透率呈“椭圆”分布,渗透率最大可达到1.07×10-6 m2,最小可达到1.5×10-8 m2;随着高度的增加,采空区两侧的渗透率变化幅度增加,中部的渗透率变化值较小。断裂带渗透率呈“铲状”分布,靠近工作面区域渗透率最大,断裂带的渗透率在上下隅角处最大可达到1.8×10-10 m2,垂直方向上随着高度的增加渗透率减小。研究结果可为西部典型浅埋煤层安全高效开采提供现场指导作用。     

扬州市区水环境质量现状及防治对策

通过对扬州市区境内河流和地下水的环境质量进行调查分析,结果表明：河流水质较好,城区污水都排入污水处理厂且处理厂正常运行,水质达标排放,主要的污染物是有机污染物;地下水达到水质标准,由于地质原因,主要污染指标为总硬度和总矿化度。但仍应加大污染防治力度,针对水环境现状和问题,采取有效措施,坚持深入开展环境宣传教育,依靠科技进步,科学防治环境污染,控制污染源,实行达标制度,提高人们自身环保意识,促进水资源的可持续利用。     

Ionic composition of submicron particles (PM1.0) during the long-lasting haze period in January 2013 in Wuhan, central China

In January 2013, a long-lasting severe haze episode occurred in Northern and Central China; at its maximum, it covered a land area of approximately 1.4 million km². In Wuhan, the largest city in Central China, this event was the most severe haze episode in the 21st century. Aerosol samples of submicron particles (PM_1.0) were collected during the long-lasting haze episode at an urban site and a suburban site in Wuhan to investigate the ion characteristics of PM_1.0 in this area. The mass concentrations of PM_1.0 and its water-soluble inorganic ions (WSIIs) were almost at the same levels at two sites, which indicates that PM_1.0 pollution occurs on a regional scale in Wuhan. WSIIs (Na⁺, NH₄⁺, K⁺, Mg²⁺, Ca²⁺, Cl^-, NO₃^- and SO₄^2-) were the dominant chemical species and constituted up to 48.4% and 47.4% of PM_1.0 at WD and TH, respectively. The concentrations of PM_1.0 and WSIIs on haze days were approximately two times higher than on normal days. The ion balance calculations indicate that the particles were more acidic on haze days than on normal days. The results of the back trajectory analysis imply that the high concentrations of PM_1.0 and its water-soluble inorganic ions may be caused by stagnant weather conditions in Wuhan.     

广州地区孕妇羊水中PCBs暴露水平初步研究

随机采集广州地区非职业PCBs(polychlorinated biphenyls,多氯联苯)暴露单胎孕妇分娩时羊水,分析羊水中PCBs浓度水平;结合孕妇临床资料(年龄、孕周、身体质量指数(body mass index,BMI))以及孕妇居住环境信息等,阐明了广州地区非职业暴露孕妇羊水PCBs蓄积的影响因素。结果表明,∑33PCBs浓度为15.91-324.38 ng·g-1,平均值为114.34±83.52 ng·g-1,中值为84.8 5ng·g-1;其中十氯含量最低,平均浓度为2.66±3.46 ng·g-1,中值为1.47 ng·g-1;六氯PCBs含量最高,平均浓度为28.79±33.84 ng·g-1,中值为17.48 ng·g-1。样本中有31种PCBs同分异构体在孕妇羊水中检出,分别为PCB 8、28、30、49、52、70、74、77、82、87、99、101、105、114、118、126、128、138、153、156、158、166、169、170、179、180、183、187、189、198和209;羊水主要的PCBs暴露以五氯PCBs、六氯PCBs和七氯PCBs为主,主要的同分异构体为PCB 138(4.73%)、179(4.15%)、153(3.92%)、183(3.89%)、166(3.77%)、187(3.74%)以及180(3.67%);暴露水平与美国、西班牙、加拿大等地区相比属于严重水平。统计结果显示,年龄、身体质量指数和孕周与PCBs蓄积有显著性正相关关系;工业区居住的孕妇相与非工业区居住孕妇相比,上述统计结果更为显著。     

银川东换流站MRTB转换失败引起闭锁原因分析

针对银川东换流站金属回线转换开关(Metallic Return Transfer Breaker,MRTB)转换失败引起直流闭锁的问题,通过对 MRTB 动作顺序、避雷器击穿原因、银川东换流站和胶东换流站保护动作进行分析,提出了采用延时 90 s 开放逆变站金属回线接地保护使能信号的方法,解决在转化过程中由于 MRTB 重合造成保护误动的问题。应用结果表明:该方法可以有效避免直流闭锁,保证了直流系统可靠运行。     

呼吸道防护基础理论及产品生产技术

本文重点论述了有关呼吸道防护的相关基础理论和用于呼吸道防护非织造布的生产技术.首先介绍了呼吸道防护中最基础的过滤理论,其中包括纤维束结构中的速度场和过滤效率以及单纤维过滤机理;其次介绍了非织造过滤材料的分类和非织造布的生产技术;最后介绍了呼吸道防护滤材的性能评估标准.