Interinstrument comparison of remote-sensing devices and a new method for calculating on-road nitrogen oxides emissions and validation of vehicle-specific power

Emissions of nitrogen oxides (NOx) by vehicles in real driving environments are only partially understood. This has been brought to the attention of the world with recent revelations of the cheating of the type of approval tests exposed in the dieselgate scandal. Remote-sensing devices offer investigators an opportunity to directly measure in situ real driving emissions of tens of thousands of vehicles. Remote-sensing NO₂ measurements are not as widely available as would be desirable. The aim of this study is to improve the ability of investigators to estimate the NO₂ emissions and to improve the confidence of the total NOx results calculated from standard remote-sensing device (RSD) measurements. The accuracy of the RSD speed and acceleration module was also validated using state-of-the-art onboard global positioning system (GPS) tracking. Two RSDs used in roadside vehicle emissions surveys were tested side by side under off-carriageway conditions away from transient pollution sources to ascertain the consistency of their measurements. The speed correlation was consistent across the range of measurements at 95% confidence and the acceleration correlation was consistent at 95% confidence intervals for all but the most extreme acceleration cases. VSP was consistent at 95% confidence across all measurements except for those at VSP ≥ 15 kW t^?1, which show a small underestimate. The controlled distribution gas nitric oxide measurements follow a normal distribution with 2σ equal to 18.9% of the mean, compared to 15% observed during factory calibration indicative of additional error introduced into the system. Systematic errors of +84 ppm were observed but within the tolerance of the control gas. Interinstrument correlation was performed, with the relationship between the FEAT and the RSD4600 being linear with a gradient of 0.93 and an R² of 0.85, indicating good correlation. A new method to calculate NOx emissions using fractional NO₂ combined with NO measurements made by the RSD4600 was constructed, validated, and shown to be more accurate than previous methods.

Implications: Synchronized remote-sensing measurements of NO were taken using two different remote-sensing devices in an off-road study. It was found that the measurements taken by both instruments were well correlated. Fractional NO₂ measurements from a prior study, measurable on only one device, were used to create new NO_x emission factors for the device that could not be measured by the second device. These estimates were validated against direct measurement of total NO_x emission factors and shown to be an improvement on previous methodologies. Validation of vehicle-specific power was performed with good correlation observed.     

Practitioner Insights into Weed Management on California’s Rangelands and Natural Areas

Working rangelands and natural areas span diverse ecosystems and face both ecological and economic threats from weed invasion. Restoration practitioners and land managers hold a voluminous cache of place-based weed management experience and knowledge that has largely been untapped by the research community. We surveyed 260 California rangeland managers and restoration practitioners to investigate invasive and weedy species of concern, land management goals, perceived effectiveness of existing practices (i.e., prescribed fire, grazing, herbicide use, and seeding), and barriers to practice implementation. Respondents identified 196 problematic plants, with yellow starthistle (Centaurea solstitialis L.) and medusahead (Elymus caput-medusae L.) most commonly listed. Reported adoption and effectiveness of weed management practices varied regionally, but the most highly rated practice in general was herbicide use; however, respondents identified considerable challenges including nontarget effects, cost, and public perception. Livestock forage production was the most commonly reported management goals (64% of respondents), and 25% of respondents were interested in additional information on using grazing to manage invasive and weedy species; however, 19% of respondents who had used grazing for weed management did not perceive it to be an effective tool. Across management practices, we also found common barriers to implementation, including operational barriers (e.g., permitting, water availability), potential adverse impacts, actual effectiveness, and public perception. Land manager and practitioner identified commonalities of primary weeds, management goals, perceived practice effectiveness, and implementation barriers across diverse bioregions highlight major needs that could be immediately addressed through management–science partnerships across the state’s expansive rangelands and natural areas.     

Applying 3DCE to environmentally responsible manufacturing practices

A review of recent literature in the fields of operations, supply chain, and management indicates there is on-going interest in improving new product development (NPD) performance. Three-dimensional concurrent engineering (3DCE), the simultaneous design of product, process and supply chain have been proposed as a way to improve traditional NPD outcomes, such as reduced time to market, lower costs, and improved customer acceptance. There appears to be a lesser concern associated with the environmental impacts of new products. Environmentally responsible manufacturing (ERM) on new product development focuses on reduced emissions, hazardous materials elimination, and lower product weight without sacrificing functionality. This paper explores the following issue: will employing 3DCE to integrate NPD and ERM yield better benefits than the separate and uncoordinated application of environmental goals and NPD initiatives?     

Urban impacts on regional carbonaceous aerosols: Case study in central Texas

Rural and background sites provide valuable information on the concentration and optical properties of organic, elemental, and water-soluble organic carbon (OC, EC, and WSOC), which are relevant for understanding the climate forcing potential of regional atmospheric aerosols. To quantify climate- and air quality-relevant characteristics of carbonaceous aerosol in the central United States, a regional background site in central Texas was chosen for long-term measurement. Back trajectory (BT) analysis, ambient OC, EC, and WSOC concentrations and absorption parameters are reported for the first 15 months of a long-term campaign (May 2011–August 2012). BT analysis indicates consistent north–south airflow connecting central Texas to the Central Plains. Central Texas aerosols exhibited seasonal trends with increased fine particulate matter (<2.5 μm aerodynamic diameter, PM_2.5) and OC during the summer (PM_2.5 = 10.9 μg m^?3 and OC = 3.0 μg m^?3) and elevated EC during the winter (0.22 μg m^?3). When compared to measurements in Dallas and Houston, TX, central Texas OC appears to have mixed urban and rural sources. However, central Texas EC appears to be dominated by transport of urban emissions. WSOC averaged 63% of the annual OC, with little seasonal variability in this ratio. To monitor brown carbon (BrC), absorption was measured for the aqueous WSOC extracts. Light absorption coefficients for EC and BrC were highest during summer (EC MAC = 11 m² g^?1 and BRC MAE₃₆₅ = 0.15 m² g^?1). Results from optical analysis indicate that regional aerosol absorption is mostly due to EC with summertime peaks in BrC attenuation. This study represents the first reported values of WSOC absorption, MAE₃₆₅, for the central United States.

Implications:Background concentration and absorption measurements are essential in determining regional potential radiative forcing due to atmospheric aerosols. Back trajectory, chemical, and optical analysis of PM_2.5 was used to determine climatic and air quality implications of urban outflow to a regional receptor site, representative of the central United States. Results indicate that central Texas organic carbon has mixed urban and rural sources, while elemental carbon is controlled by the transport of urban emissions. Analysis of aerosol absorption showed black carbon as the dominant absorber, with less brown carbon absorption than regional studies in California and the southeastern United States.     

In vitro methane removal by volcanic pumice soil biofilter columns over one year

Soil methane (CH(4)) biofilters, containing CH(4)-oxidizing bacteria (methanotrophs), are a promising technology for mitigating greenhouse gas emissions. However, little is known about long-term biofilter performance. In this study, volcanic pumice topsoils (0-10 cm) and subsoils (10-50 cm) were tested for their ability to oxidize a range of CH(4) fluxes over 1 yr. The soils were sampled from an 8-yr-old and a 2-yr-old grassed landfill cover and from a nearby undisturbed pasture away from the influence of CH(4) generated by the decomposing refuse. Methane was passed through the soils in laboratory chambers with fluxes ranging from 0.5 g to 24 g CH(4) m(-3) h(-1). All topsoils efficiently oxidized CH(4). The undisturbed pasture topsoil exhibited the highest removal efficiency (24 g CH(4) m(-3) h(-1)), indicating rapid activation of the methanotroph population to the high CH(4) fluxes. The subsoils were less efficient at oxidizing CH(4) than the topsoils, achieving a maximum rate oxidation rate of 7 g CH(4) m(-3) h(-1). The topsoils exhibited higher porosities; moisture contents; surface areas; and total C, N, and available-P concentrations than the subsoils, suggesting that these characteristics strongly influence growth and activity of the CH(4)-oxidizing bacteria. Soil pH values and available-P levels gradually declined during the trial, indicating a need to monitor chemical parameters closely so that adjustments can be made when necessary. However, other key soil physicochemical parameters (moisture, total C, total N) increased over the course of the trial. This study showed that the selected topsoils were capable of continually sustaining high CH(4) removal rates over 1 yr, which is encouraging for the development of biofilters as a low-maintenance greenhouse gas mitigation technology.     

CH4/CO2 ratios indicate highly efficient methane oxidation by a pumice landfill cover-soil

Landfills that generate too little biogas for economic energy recovery can potentially offset methane (CH₄) emissions through biological oxidation by methanotrophic bacteria in cover soils. This study reports on the CH₄ oxidation efficiency of a 10-year old landfill cap comprising a volcanic pumice soil. Surface CH₄ and CO₂ fluxes were measured using field chambers during three sampling intervals over winter and summer. Methane fluxes were temporally and spatially variable (?0.36 to 3044 mg CH₄ m^?2 h^?1); but were at least 15 times lower than typical literature CH₄ fluxes reported for older landfills in 45 of the 46 chambers tested. Exposure of soil from this landfill cover to variable CH₄ fluxes in laboratory microcosms revealed a very strong correlation between CH₄ oxidation efficiency and CH₄/CO₂ ratios, confirming the utility of this relationship for approximating CH₄ oxidation efficiency. CH₄/CO₂ ratios were applied to gas concentrations from the surface flux chambers and indicated a mean CH₄ oxidation efficiency of 72%. To examine CH₄ oxidation with soil depth, we collected 10 soil depth profiles at random locations across the landfill. Seven profiles exhibited CH₄ removal rates of 70–100% at depths <60 cm, supporting the high oxidation rates observed in the chambers. Based on a conservative 70% CH₄ oxidation efficiency occurring at the site, this cover soil is clearly offsetting far greater CH₄ quantities than the 10% default value currently adopted by the IPCC.     

Shape memory polymer snap-fits for active disassembly

This paper explores a means to simplify disassembly by engineering a snap-fit that automatically releases upon exposure to a heat field thus limiting manual labor or machine operation for disassembly. Shape memory polymer (SMP) snap-fits were designed and manufactured to actively release upon a thermal trigger. Snap-fits were designed with an added feature known here as a release angle that would allow for an uninterrupted movement for disassembly in the presence of an elevated temperature. SMP snap-fits were then manufactured and tested. Testing was performed for demonstration of the active release of the SMP snap-fits and for analysis of active disassembly (AD) process parameters. Taguchi methods were used to analyze the AD process parameters, including heating method and disassembly temperature. The results from this research show the successful demonstration of the SMP snap-fits within a manufactured product housing. AD process parameter analysis shows that both the heating method and temperature affect the AD process. The analysis determines that by increasing the heat exchange rate the snap-fit disassembly time is shortened. From the performed experiments, it was seen that an Oil bath at 150 °C produced the best results in regards to disassembly time and signal-noise ratio. The results from experimentation demonstrate the possibility of acceptable heat-releasable fasteners for more efficient disassembly and exhibit benefits over current AD elements comprised of shape memory alloys.     

Nitrate and sediment fluxes from a California rangeland watershed

Long-term water quality records for assessing natural variability, impact of management, and that guide regulatory processes to safeguard water resources are rare for California oak woodland rangelands. This study presents a 20-yr record (1981-2000) of nitrate-nitrogen (NO(3)-N) and suspended sediment export from a typical, grazed oak woodland watershed (103 ha) in the northern Sierra Nevada foothills of California. Mean annual precipitation over the 20-yr period was 734 mm yr(-1) (range 366-1205 mm yr(-1)). Mean annual stream flow was 353 mm y(-1) (range 87-848 mm yr(-1)). Average annual stream flow was 48.1 +/- 16% of precipitation. Mean annual NO(3)-N export was 1.6 kg ha(-1) yr(-1) (range 0.18-3.6 kg ha(-1) yr(-1)). Annual NO(3)-N export significantly (P < 0.05) increased with increasing annual stream flow and precipitation. Mean daily NO(3)-N export was 0.004 kg ha(-1) d(-1) (range 10(-5) to 0.55 kg ha(-1) d(-1)). Mean annual suspended sediment export was 198 kg ha(-1) yr(-1) (range 23-479 kg ha(-1) yr(-1)). There was a positive relationship (P < 0.05) between annual suspended sediment export, annual stream flow and precipitation. Mean daily suspended sediment export was 0.54 kg ha(-1) d(-1) (range 10(-4) to 155 kg ha(-1) d(-1)). Virtually no sediment was exported during the dry season. The large variation in daily and annual fluxes highlights the necessity of using long-term records to establish quantitative water quality targets for rangelands and demonstrates the difficulty of designing a water quality monitoring program for these ecosystems.     

Efficacy of vegetated buffer strips for retaining Cryptosporidium parvum

Overland and shallow subsurface hydrologic transport of pathogenic Cryptosporidium parvum oocysts from cattle feces into surface drinking water supplies is a major concern on annual grasslands in California's central and southern Sierra Nevada foothills. Soil boxes (0.5 m wide x 1.1 m long x 0.3 m deep) were used to evaluate the ability of grass vegetated buffer strips to retain 2 x 10(8) spiked C. parvum oocysts in 200-g fecal deposits during simulated rainfall intensities of 30 to 47.5 mm/h over 2 h. Buffers were comprised of Ahwahnee sandy loam (coarse-loamy, mixed, active, thermic Mollic Haploxeralfs; 78:18:4 sand to silt to clay ratio; dry bulk density = 1.4 g/cm(3)) set at 5 to 20% land slope, and >/=95% grass cover (grass stubble height = 10 cm; biomass = 900 kg/ha dry weight). Total number of oocysts discharged from each soil box (combined overland and subsurface flow) during the 120-min simulation ranged from 1.5 x 10(6) to 23.9 x 10(6) oocysts. Observed overall mean log(10) reduction of total C. parvum flux per meter of vegetated buffer was 1.44, 1.19, and 1.18 for buffers at 5, 12, and 20% land slope, respectively. Rainfall application rate (mm/h) was strongly associated with oocyst flux from these vegetated buffers, resulting in a decrease of 2 to 4% in the log(10) reduction per meter buffer for every additional mm/h applied to the soil box. These results support the use of strategically placed vegetated buffers as one of several management strategies that can reduce the risk of waterborne C. parvum attributable to extensive cattle grazing on annual grassland watersheds.     

Farm factors associated with reducing Cryptosporidium loading in storm runoff from dairies

A systems approach was used to evaluate environmental loading of Cryptosporidium oocysts on five coastal dairies in California. One aspect of the study was to determine Cryptosporidium oocyst concentrations and loads for 350 storm runoff samples from dairy high use areas collected over two storm seasons. Selected farm factors and beneficial management practices (BMPs) associated with reducing the Cryptosporidium load in storm runoff were assessed. Using immunomagnetic separation (IMS) with direct fluorescent antibody (DFA) analysis, Cryptosporidium oocysts were detected on four of the five farms and in 21% of storm runoff samples overall. Oocysts were detected in 59% of runoff samples collected near cattle less than 2 mo old, while 10% of runoff samples collected near cattle over 6 mo old were positive. Factors associated with environmental loading of Cryptosporidium oocysts included cattle age class, 24 h precipitation, and cumulative seasonal precipitation, but not percent slope, lot acreage, cattle stocking number, or cattle density. Vegetated buffer strips and straw mulch application significantly reduced the protozoal concentrations and loads in storm runoff, while cattle exclusion and removal of manure did not. The study findings suggest that BMPs such as vegetated buffer strips and straw mulch application, especially when placed near calf areas, will reduce environmental loading of fecal protozoa and improve stormwater quality. These findings are assisting working dairies in their efforts to improve farm and ecosystem health along the California coast.