Numerical study of heat transfer characteristics of char from waste tire pyrolysis

To investigate heat transfer of char from waste tire pyrolysis, the cooling of char was simulated by the computational fluid dynamics. To scrutinize the heat transfer characteristics, bed height, temperature of cooling wall, and mixing time were selected as calculation parameters. From the results, increasing the char bed height from 0.005 to 0.02 m, the total heat transfer is decreased as from 45.5 to 26.5 J. As the char bed height is further increased from 0.02 to 0.06 m, the total heat transfer is decreased from 26.5 to 9.1 J. The char bed height affects the total heat transfer significantly. The total heat transfer decreases from 15.9 to 14.0 J as the temperature of cooling wall increases from 273.15 to 323.15 K. The total heat transfer mildly depends on the temperature of cooling wall. The particle mixing time increases from 10 to 120 s and the total heat transfer decreases from 28.6 to 22.6 J. It is noted that the particle contact is enhanced between char particles as well as the particles and cooling wall as the particle mixing time decreases. Consequently, heat transfer is augmented.     

STREAM DISCHARGE PREDICTION VIA A GRID BASED SOIL WATER ROUTING WITH PADDY FIELDS1

ABSTRACT: A grid based daily hydrologic model for a watershed with paddy fields was developed to predict the stream discharge. ASCII formatted elevation, soil, and land use data supported by the GRASS Geographic Information System are used to generate distributed results such as surface runoff and subsurface flow, soil water content, and evapotranspiration. The model uses a single flow path algorithm and simulates a water balance at each grid element. A linear reservoir assumption was used to predict subsurface runoff components. The model was applied to a 75.6 km² watershed located in the middle of South Korea, and observed stream flow hydrographs from 1995 and 1996 were compared to model predictions. The stream flow predictions of 1995 and 1996 generally agreed with the observed flow, resulting in a Nash‐Sutcliffe efficiency R² of 0.60 and 0.62, respectively. The hydraulic conductivity for percolating water through the saturated layer affected baseflow generation. The levee height of the paddy influenced the time and magnitude of the surface runoff, depending on irrigation management. The model will be used for making low flow management decisions by evaluating the role of each land use to stream flow, especially in case of paddy decrease by gradual urbanization of a watershed.     

Analysis of the nitrifying bacterial community in BioCube sponge media using fluorescent in situ hybridization (FISH) and microelectrodes

There is growing interest in the development of more cost-effective and retrofit technologies for the upgrade and expansion of existing wastewater treatment plants with extreme space constraints. A free-floating sponge media (BioCube) process, using a 24L lab scale reactor, was operated to study the nitrification profiles and microbial community. The COD removal efficiencies were maintained, at an average of 95%, with the mixed liquor suspended solids (MLSS) inside the BioCube sponge media maintained at 12,688mg/L. The nitrification removal efficiencies were between 92% and 100%, with an average value of 99%. From the results of microelectrode measurements, the ammonium ion concentration was found to rapidly decrease from the surface of the BioCube sponge media to a depth of 2mm due to chemical reactions carried out by ammonia oxidizing bacteria (AOB) species. Multi-fluorescence in situ hybridization (FISH) has been used to investigate the spatial distributions of various microbial activities within reactors. Microbial communities were targeted using different oligonucleotide probes specific to AOB and nitrite oxidizing bacteria (NOB). There were a large number of AOB populations, but these were not uniformly distributed in the biofilm compared to the NOB populations.     

In-situ electrochemical measurements of total concentration and speciation of heavy metals in acid mine drainage (AMD): assessment of the use of anodic stripping voltammetry

We assessed the use of anodic stripping voltammetry (ASV) for in-situ determinations of both total concentration and speciation of dissolved heavy metals (Cd, Cu, Pb and Zn) in acid mine drainage (AMD). In the Kwangyang Au–Ag mine area of South Korea, different sites with varying water chemistry within an AMD were studied with a field portable anodic stripping voltammeter. Anodic stripping voltammetry after wet oxidation (acidification) was very sensitive enough to determine total concentration of dissolved Cd because Cd was dominantly present as ‘labile’ species, whilst the technique was not so effective for determining total Cu especially in the downstream sites from the retention pond, due to its complexation with organic matter. For dissolved Pb, the concentrations determined by ASV after wet oxidation generally agreed with those by ICP-AES. In the downstream samples (pH>5), however, ASV data after wet oxidation were lower than ICP-AES data because a significant fraction of dissolved Pb was present in those samples as ‘inert’ species associated with colloidal iron oxide particles. The determination of total dissolved Zn by ASV after wet oxidation appeared to be unsatisfactory for the samples with high Cu content, possibly due to the interference by the formation of Zn–Cu intermetallic compounds on the mercury coated electrode. In AMD samples with high dissolved iron, use of ultraviolet irradiation was not effective for determining total concentrations because humate destruction by UV irradiation possibly resulted in the removal of a part of dissolved heavy metals from waters through the precipitation of iron hydroxides.     

One-at-a-time sensitivity analysis of pollutant loadings to subsurface properties for the assessment of soil and groundwater pollution potential

Chemical leak was numerically simulated for four chemical substances: benzene (light non-aqueous phase liquid (NAPL)), tetrachloroethylene (dense NAPL), phenol (soluble in water), and pentachlorophenol (white crystalline solid) in a hypothetical subsurface leak situation using a multiphase compositional transport model. One metric ton of chemical substances was assumed to leak at a point 3.51 m above the water table in a homogeneous unconfined aquifer which had the depth to water table of 7.135 m, the hydraulic gradient of 0.00097, the recharge rate of 0.7 mm/day, and the permeability of 2.92?×?10^?10 m². For comparison, surface spill scenarios, which had a long pathway from source to the water table, were simulated. Using the model results, point-source pollutant loadings to soil and groundwater were calculated by multiplying mass, impact area, and duration above and below the water table respectively. Their sensitivity to subsurface properties (depth to water table, recharge rate, porosity, organic carbon content, decay rate, hydraulic gradient, capillary pressure, relative permeability, permeability) was analyzed, with changing each parameter within acceptable ranges. The study result showed that the pollutant loading to groundwater was more sensitive to the subsurface properties than the pollutant loading to soil. Decay rate, groundwater depth, hydraulic gradient and porosity were influential to pollutant loadings. The impact of influential parameters on pollutant loadings was nonlinear. The dominant subsurface properties of pollution loadings (e.g., decay rate, groundwater depth, hydraulic gradient, and porosity for groundwater) also affect the vulnerability, and the subsurface pollutant loadings defined in this study are dependent on chemical properties as well, which indicates that the influential hydrogeological and physicochemical parameters to pollutant loadings can be used for pollution potential assessment. The contribution of this work is the suggestion that the sensitivity of pollutant loadings can be used for pollution potential assessment. Soil and groundwater pollution potential of chemicals are discussed altogether for leak scenarios. A physics-based model is used to understand the impact of subsurface properties on the fate and transport of chemicals above and below the water table, and consequently their impact on the pollutant loading to soil and groundwater.

     

US Energy Conservation and Efficiency: Benefits and Costs

With increased energy conservation plus the adoption of diverse energy efficient technologies, the US economy could save about 32 quads or about 33% of its current energy consumption, if sound conservation energy use policies were implemented over approximately 10 years. This potential of 32 quads is slightly greater than the current US oil imports. The systems that have the greatest potential to provide major energy savings are transportation, residential energy use, and the food system. Not only saving energy has merit in itself, but it would save US citizens approximately $438 billion per year, helping support the US economy, a high standard of living, and energy security. In addition, this analysis suggests that reducing the $40 billion in taxpayer money spent on subsidies of the energy industries would further increase conservation.     

Congratulatory Address

Water, Air, &; Soil Pollution: Focus -     

Contamination by Cd, Cu, Pb, and Zn in mine wastes from abandoned metal mines classified as mineralization types in Korea

The objective of this study was to investigate heavy metal contamination and geochemical characteristics of mine wastes, including tailings, from 38 abandoned mines classified as five mineralization types. Mine waste materials including tailings and soils were sampled from the mines and the physical and chemical characteristics of the samples were analyzed. The particle size of tailings was in the range of 10–100 μm. The pH of the waste covered a wide range, from 1.73 to 8.11, and was influenced by associated minerals and elevated levels of Cd, Cu, Pb, and Zn, extracted by a Korean Standard Method (digestion with 0.1 mol L⁻¹ HCl), which were found in the wastes. Half of the samples contained heavy metals at levels above those stipulated by the Soil Environmental Conservation Act (SECA) in Korea. In addition, extremely high concentrations of the metals were also found in mine wastes extracted by aqua regia, especially those from mines associated with sulfide minerals. Thus, it can be expected that trace elements in mine wastes may be dispersed both downstream and downslope through water and wind. Eventually they may pose a potential health risk to residents in the vicinity of the mine. It is necessary to control mine wastes by using a proper method for their reclamation, such as neutralization of the mine wastes using a fine-grained limestone.     

Relative extraction ratio (RER) for arsenic and heavy metals in soils and tailings from various metal mines, Korea

This study focused on the evaluation of leaching behaviours for arsenic and heavy metals (Cd, Cu, Ni, Pb and Zn) in soils and tailings contaminated by mining activities. Ten representative mine soils were taken at four representative metal mines in Korea. To evaluate the leaching characteristics of the samples, eight extraction methods were adapted namely 0.1?M HCl, 0.5?M HCl, 1.0?M HCl, 3.0?M HCl, Korean Standard Leaching Procedure for waste materials (KSLP), Synthetic Precipitation Leaching Procedure (SPLP), Toxicity Characteristic Leaching Procedure (TCLP) and aqua regia extraction (AR) methods. In order to compare element concentrations as extraction methods, relative extraction ratios (RERs, %), defined as element concentration extracted by the individual leaching method divided by that extracted by aqua regia based on USEPA method 3050B, were calculated. Although the RER values can vary upon sample types and elements, they increase with increasing ionic strength of each extracting solution. Thus, the RER for arsenic and heavy metals in the samples increased in the order of KSLP?相似文献