Enhanced sludge solubilization by microbubble ozonation

A microbubble ozonation process for enhancing sludge solubilization was proposed and its performance was evaluated in comparison to a conventional ozone bubble contactor. Microbubbles are defined as bubbles with diameters less than several tens of micrometers. Previous studies have demonstrated that microbubbles could accelerate the formation of hydroxyl radicals and hence improve the ozonation of dyestuff wastewater. The results of this study showed that microbubble ozonation was effective in increasing ozone utilization and improving sludge solubilization. For a contact time of 80 min, an ozone utilization efficiency of more than 99% was obtained using the microbubble system, while it gradually decreased from 94% to 72% for the bubble contactor. The rate of microbial inactivation was obviously faster in the microbubble system. At an ozone dose of 0.02 g O₃ g⁻¹ TSS, about 80% of microorganisms were inactivated in the microbubble system, compared with about 50% inactivation for the bubble contactor. Compared to the bubble contactor, more than two times of COD and total nitrogen, and eight times of total phosphorus content were released from the sludge into the supernatant by using the microbubble system at the same ozone dosage. The application of microbubble technology in ozonation processes may provide an effective and low cost approach for sludge reduction.     

Pre-concentration and separation of heavy metal ions by chemically modified waste paper gel

Iminodiacetic acid was immobilized on waste paper by chemical modification in order to develop a new type of adsorption gel for heavy metal ions. Adsorption behavior of the gel was investigated for a number of metal ions, specifically Cu(II), Pb(II), Fe(III), Ni(II), Cd(II), and Co(II) at acidic pH. From batch adsorption tests, the order of selectivity was found to be as follows: Cu(II)  Fe(III) > Pb(II) > Ni(II)  Co(II) > Cd(II). Column tests were carried out for pairs of metal ions to understand the separation and pre-concentration behavior of the gel. It was found that mutual separation of Ni(II) from Co(II) and that of Pb(II) from Cd(II) can be achieved at pH 3. Similarly, selective separation of Cu(II) from Cu(II)–Fe(III) and Cu(II)–Pb(II) mixtures at pH 1.5 and 2, respectively, was observed by using this new adsorption gel. In all cases, almost complete recovery of the adsorbed metal was confirmed by elution tests with HCl.     

Spatial cost efficiency in waste paper handling: the case of corrugated board in Sweden

This paper analyzes the spatial cost efficiency of the Swedish legislation regarding waste disposal handling. We focus on the case of corrugated board and recognize that the different counties in Sweden possess different economic prerequisites in terms of waste paper recovery and utilization potential. We employ data for six corrugated board mills and 20 counties and a non-linear programming model to identify the least cost strategy for reaching the politically specified recycling target of a 65% recovery rate for corrugated board. That is, the total costs of recovering a minimum of 65% in each county are calculated and compared with the case when the country as a whole recovers 65% of all old corrugated board is collected but there exist no uniform target for each county. The conclusion is that from an efficiency point of view the recovery efforts should be concentrated to the highly populated and urbanized counties, and not be uniformly divided throughout the country. In the base case, the results suggest that the cost efficient county-specific recovery rates should range from 51 to 72%.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

废塑料再生过程废水中微塑料去除模拟试验

微塑料是一种存在于不同环境介质中的新兴污染物,主要来源于废弃塑料制品,其存在污染范围广、潜在环境污染大的问题.废塑料再生企业生产废水中微塑料浓度远高于其他类型废水,对其生产废水中的微塑料进行处理具有重要的环境意义.模拟废塑料再生过程的生产废水并进行微塑料去除的絮凝沉淀试验,研究絮凝剂投加量、pH、水力快速搅拌条件的单因素和正交试验对废水中微塑料去除率及其各因素作用的影响.结果表明:①当PAC (聚合氯化铝)投加量为10 mL,PAM (聚丙烯酰胺)投加量为7 mL,pH为9,水力快速搅拌条件为100 r/min下维持40 s再200 r/min下维持40 s时,微塑料的总去除率最高,达91%.②PAC投加量是影响微塑料去除效果的主要因素,其次是pH.③微塑料的去除率与其本身的密度有关,密度大的ABS (acrylonitrile butadiene styrene,丙烯腈-丁二烯-苯乙烯)去除率最高,密度小的PE (polyethylene,聚乙烯)去除率最低.④不同粒径区间的微塑料去除率区别较大,粒径小(0.1~0.25 mm)的微塑料去除效果最好.研究显示,通过控制PAC和PAM的投加量、pH和水力搅拌速率等条件,能够有效将废水中的微塑料通过絮凝沉淀的方法去除,从而达到净化含微塑料生产废水的目的.      

中国乘用车塑料的动态物质流分析

结合行业信息并基于动态物质流模型,本文对1950~2050年间中国乘用车塑料流量与存量进行了历史测算与情景分析.历史测算表明：1950~2018年国内乘用车行业累计消耗了以聚丙烯（PP）、聚氨酯（PU）等为主的塑料3278万t,产生了337万t塑料废弃物;报废汽车拆解后的车用废塑料仅28%得到回收利用.针对未来情况,本文设计了乘用车保有量、单车塑料使用量两大关键因素下的不同情景组合.结果显示车用塑料存量及废塑料产生量将大幅增长,到2050年存量将达到0.7~2.7亿t,废塑料产生量将达到500~1600万t,汽车拆解和塑料再生等相关行业对此应充分关注.到2050年车用废塑料回收率若能提升至80%,将减少376万t/a的车用废塑料填埋或焚烧,显著减少环境风险.     

低温等离子体协同催化降解废气污染物的研究进展

阐述了低温等离子体协同催化工艺流程与反应机理,探讨了反应温度、废气进口组分、废气中水蒸气含量、气体流速、气溶胶等因素对降解效果的影响。分析认为:一段式低温等离子体协同催化可改变低温等离子体特征及催化剂催化特性,但尚未解决尾气臭氧逃逸、副产物产生及放电稳定性等问题;两段式低温等离子体协同催化可提高污染物分子降解效率并减少尾气臭氧逃逸,但未能有效利用等离子体的能量,气体中的水蒸气、粉尘及反应过程中产生的气溶胶均能影响后置催化剂的催化性能;两段式低温等离子体协同催化已具备工程应用条件,还需配套高效预处理单元以降低废气中水蒸气、粉尘等对催化剂的影响。     

环境监测实验室废液的管理与处理方法

环境监测实验室的废液处理常常被忽视,提出建立有效的废液管理制度的必要性.有针对性地介绍了环境监测实验室中常见废液的处理方法.     

Modelling of Materials Policies

This paper discusses the REAP1 model and its application for the analysis of CO₂ reduction and waste management policies for Japanese petrochemicals. The pros and cons of this modelling approach in comparison to other tools is elaborated. This is followed by a discussion of the model code and the modelling results. The results show that CO₂ policies can have significant impacts on waste flows and waste policies can have significant CO₂ benefits. As a consequence both effects must be considered in policy assessment. Pricing instruments are recommended instead of regulations because of the complex physical relations in the materials life cycle that extend beyond sector boundaries. A taxation approach is superior to a subsidy approach because rebound effects can be avoided.     

消泡剂硅油I在工业废水氨氮测定中的应用

对色泽较深，含杂质量较高的废水加硅油I以抑制测定中蒸馏产生的泡沫．结果表明，在250ml水样中加硅油IO．10～1．25ml，即可收到理想效果．硅油I性质稳定，不随水蒸汽蒸出，对测定无干扰．