A closer look at BLEVE overpressure

The overpressure produced by the boiling liquid expanding vapor explosion (BLEVE) is still not well understood. Various methods have been published on the overpressure modeling in the far field. They mostly differ by the modeling of the expansion energy, used to scale the distance to the source where the overpressure needs to be calculated. But these methods usually include a experimentally fitted reduction factor, and are mostly overestimating the overpressures. Today there is a growing interest in modeling the BLEVE overpressure in the near field, for studying the blast effect on critical infrastructure such as bridges and buildings. This requires a much better understanding of the BLEVE blast. This paper goes deeper in the understanding of the physical phenomenon leading to the BLEVE blast wave generation and propagation. First, mid-scale BLEVE experiments in addition to new experimental data for near field blast from a small scale supercritical BLEVE are analyzed. And second, an analysis method of the shocks observed in the experiments is presented based on fundamental gas dynamics, and allows the elaboration of a new modeling approach for BLEVE overpressure, based on the calculation of the initial overpressure and radius of the blast.     

初始温度和压力对排污空间甲烷-空气混合物爆燃特性影响的模拟研究

市政排污空间作为城市公共基础设施的重要组成部分，易积聚可燃气体形成爆炸性环境。结合排污空间的特殊环境条件，采用Fluidyn-MP多物理场数值模拟软件，建立了20 L球形爆炸罐分析模型，通过改变初始温度和初始压力，对排污空间甲烷-空气混合物爆燃特性及其变化规律进行模拟研究。结果表明:初始温度升高导致甲烷-空气混合物最大爆炸压力降低，缩短了到达最大爆炸压力的时间；初始压力增加导致最大爆炸压力急剧升高，并延长了到达最大爆炸压力的时间；最大爆炸压力对初始压力的敏感程度远大于初始温度的影响。此外，随着初始温度和初始压力的升高，爆炸火焰平均传播速度增加，而火焰传播速度对初始温度较敏感。     

湖北省2008年初低温雨雪冰冻过程气候特征分析

2008年初，湖北省出现了严重的低温雨雪冰冻灾害，直接经济损失高达110亿元以上，有必要对灾害期间的气候特征进行系统、科学的分析和总结。对湖北省76个气象站2008年1月12日～2月3日气温、降水（雪）、日照以及低温持续日数等要素进行时空间差异分析及历史与同期比较，并选取10个代表站历史上所有低温雨雪天气过程，对其过程持续低温日数、最长连续雨雪日数、过程极端低温进行比较分析。结果表明：（1）此次过程的平均气温异常偏低，该省大部为-1～-2℃，比常年同期偏低4～6℃，为各站历史同期最低，其中主要是最高气温异常偏低所致，但极端低温并不低；（2）降雪过程频繁，雨雪量异常偏多；（3）低温冰冻持续时间长，该省大部在16～22 d，位于历史第一；（4）日照异常偏少。持续而稳定的大气环流异常形势是湖北省大范围低温雨雪天气的直接原因。     

Air Temperature Changes in a Steppe Marmot Burrow in the Summer–Autumn Period

Observations of air temperature changes in a steppe marmot burrow were performed from late July to mid-October. Until early September, temperature in the burrow remained relatively constant, but then it began to decrease rapidly. This occurred after air temperature above the ground became equal to the temperature in the burrow. Supposedly, it is in this particular period that marmots begin to plug the entrance to the burrow with earth, thus reducing heat exchange between the increasingly cold aboveground air and the air in the burrow.     

基于两种再分析资料的一次四川盆地大气污染过程气象要素数值模拟研究

利用ECMWF-ERA5和NCEP-FNL再分析资料作为中尺度气象模式WRF（The Weather Research and Forecasting）初始场,对四川盆地2018年1月一次大气污染过程气象要素进行了模拟,对比分析了气温、风速、风向、相对湿度、边界层高度、温廓线的模拟效果,并结合大气超级站观测数据对模拟结果进行评估.结果表明：两种资料均能较好地模拟出气象要素的变化情况,但由于两套资料时空分辨率、采用的模式、同化方案、数据来源和质量控制方案存在一定区别,导致各要素模拟效果并不一致.与NCEP-FNL相比,ECMWF-ERA5模拟的平均相对湿度（59.23%）与观测值差异更小,且均方根误差、偏差较小,分别为9.83%和-0.83%,但NCEP-FNL模拟的平均气温（8.99℃）更接近观测值,且偏差值较小,为-0.04℃.两组模拟结果均显示盆地内部为模拟区域的低风速区,相对湿度模拟值在60%以上,气温高于西部山地地区.NCEP-FNL模拟的盆地内部气温、相对湿度、风速小于ECMWF-ERA5模拟值,但边界层高度模拟值较大.ECMWF-ERA5模拟的逆温强度相比较小,且温度露点差较小.此次污染过程PM_2.5和PM₁₀日均浓度最大值分别为190.1 μg·m^-3和261.0 μg·m^-3,相对湿度增大引发的颗粒物吸湿增长是导致PM_2.5和PM₁₀质量浓度突增的主要原因.     

滆湖水华初期浮游植物群落特征及与水环境因子相关性分析

为探究滆湖水华初期浮游植物群落特征及与水环境因子的相关性,于2018年5—7月在全湖布设22个点,调查研究滆湖水华初期浮游植物群落时空分布特征,并对引起水华主导环境因子进行分析.结果表明：①共获得7门119属,优势属为绿藻门的小球藻与球团藻、蓝藻门的鞘丝藻与微囊藻,其中湖心区域浮游植物丰度与多样性小,均匀性低,属于中偏重污染区域;湖北区以北属于中污染区域,蓝藻堆积严重;西部沿岸及南端区域属于中偏轻污染区域.②冗余分析得出,湖心藻类与水温（T）有强相关性,与叶绿素a（Chl-a）、溶解性总磷（DTP）、pH、溶解氧（DO）呈一定正相关性;湖北区以北藻类与底泥有机质（OM）、水体悬浮物（SS）、Chl-a及DTP呈强相关性,与T呈一定相关性.T与多项环境因子相关,均值从26.1℃上升到32.4℃;OM与有机磷（OP）呈高度相关性（p<0.05,r=0.892）.水华发生的主导环境因子为T、DTP与pH,底泥OM及OP有一定影响.     

裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

金属改性对SAPO-34低温还原NO性能的影响

采用浸渍法制备金属改性SAPO-34分子筛催化剂,分析比较了不同单金属（Cu或Co）及不同比例双金属（Cu：Co=1：1、3：1、5：1,质量比）改性催化剂对NO的催化还原性能,评价了不同催化剂的N₂选择性,并采用扫描电子显微镜（SEM）、比表面积测试、X射线衍射分析（XRD）、NH₃-程序升温脱附（NH₃-TPD）等表征手段对催化剂的物化性能进行了分析.结果表明,单金属Cu改性催化剂具有较宽的温度区间,在250~450℃范围内NO的转化率始终保持在100%;双金属改性使NO转化率保持为100%的最低温度下降了25~50℃,显著拓宽了低温段窗口,其中,Cu₃Co₁/SAPO-34催化剂的低温催化还原性能最好,200℃即可实现100%的NO转化率,175℃下的转化率也高达80%以上.Cu-Co双金属改性SAPO-34分子筛催化剂具有优异的低温催化还原NO性能,具有在机动车尾气、工业废气的低温脱硝治理领域应用的潜力.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Effects of calcination temperature on physicochemical property and activity of CuSO4/TiO2 ammonia-selective catalytic reduction catalysts

CuSO_4/TiO_2 catalysts with high catalytic activity and excellent resistant to SO_2 and H_2 O,were thought to be promising catalysts used in Selective catalytic reduction of nitrogen oxides by NH_3.The performance of catalysts is largely affected by calcination temperature.Here,effects of calcination temperature on physicochemical property and catalytic activity of CuSO_4/TiO_2 catalysts were investigated in depth.Catalyst samples calcined at different temperatures were prepared first and then physicochemical properties of the catalyst were characterized by N2 adsorption-desorption,X-ray diffraction,thermogravimetric analysis,Raman spectra,Fourier-transform infrared spectroscopy,X-ray photoelectron spectroscopy,temperature-pro grammed desorption of NH_3,temperature-programmed reduction of H_2 and in situ diffuse reflectance infrared Fourier transform spectroscopy.Results revealed that high calcination temperature had three main effects on the catalyst.First,sintering and anatase transform into rutile with increase of calcination temperature,causing a decrement of specific surface area.Second,decomposition of CuSO_4 under higher calcination temperature,resulting in disappears of Br(?)nsted acid sites(S-OH),which had an adverse effect on surface acidity.Third,CuO from the decomposition of CuSO_4 changed surface reducibility of the catalyst and favored the process of NH_3 oxidation to nitrogen oxides(NO_x).Thus,catalytic activity of the catalyst calcined under high temperatures(≥600℃) decreased largely.