可张孔曝气器曝气能耗试验研究

通过试验研究，总结出可张孔曝气阻力损失的影响因素，以优化产品的结构设计参数，降低产品在工程应用中的能耗，获取更好的经济效益。     

受侧向土体位移斜桩的特性

通过三维有限单元法分析了斜桩受侧向土体位移的特性。变动柱和土体参数进行敏感性分析,得出桩的柔度、侧向土体位移的大小、桩顶约束条件、土体位移形状和土体移动层厚度等对斜桩的影响。刚性桩的挠度小于柔性桩,但弯矩和剪力大于柔性桩。斜桩非线性弹簧的土抗力—位移关系(p-y曲线)表现为双曲线特征,可基于直桩的Winkler地基反力法对斜桩进行简化计算分析,但应对直桩的极限土抗力值进行修正,以期更好的反映斜桩的特性。     

Prenatal prediction of childhood-onset spinal muscular atrophy (SMA) in Turkish families

Childhood-onset spinal muscular atrophy (SMA) is one of the most common neurodegenerative genetic disorders. SMN1 is the SMA-determining gene deleted or mutated in the majority of SMA cases. There is no effective cure or treatment for this disease yet. Thus, the availability of prenatal testing is important. Here we report prenatal prediction for 68 fetuses in 63 Turkish SMA families using direct deletion analysis of the SMN1 gene by restriction digestion. The genotype of the index case was known in 40 families (Group A) but unknown in the remaining 23 families (Group B). A total of ten fetuses were predicted to be affected. Eight of these fetuses were derived from Group A and two of these fetuses were from Group B families. Two fetuses from the same family in Group A had the SMNhyb1 gene in addition to homozygous deletion of the NAIP gene. One fetus from Group A was homozygously deleted for only exon 8 of the SMN2 gene, and further analysis showed the presence of both the SMN1 and SMNhyb1 genes but not the SMN2 gene. In addition, one carrier with a homozygous deletion of only exon 8 of the SMN1 gene was detected to have a SMNhyb2 gene, which was also found in the fetus. To our knowledge, these are the first prenatal cases with SMNhyb genes. Follow-up studies demonstrated that the prenatal predictions and the phenotype of the fetuses correlated well in 33 type I pregnancies demonstrating that a careful molecular analysis of the SMN genes is very useful in predicting the phenotype of the fetus in families at risk for SMA. Copyright © 2002 John Wiley & Sons, Ltd.     

Fecal source tracking by antibiotic resistance analysis on a watershed exhibiting low resistance

The ongoing development of microbial source tracking has made it possible to identify contamination sources with varying accuracy, depending on the method used. The purpose of this study was to test the efficiency of the antibiotic resistance analysis (ARA) method under low resistance by tracking the fecal sources at Turkey Creek, Oklahoma exhibiting this condition. The resistance patterns of 772 water-isolates, tested with nine antibiotics, were analyzed by discriminant analysis (DA) utilizing a five-source library containing 2250 isolates. The library passed various representativeness tests; however, two of the pulled-sample tests suggested insufficient sampling. The resubstitution test of the library individual sources showed significant isolate misclassification with an average rate of correct classification (ARCC) of 58%. These misclassifications were explained by low antibiotic resistance (Wilcoxon test P < 0.0001). Seasonal DA of stream E. coli isolates for the pooled sources human/livestock/deer indicated that in fall, the human source dominated (P < 0.0001) at a rate of 56%, and that human and livestock respective contributions in winter (35 and 39%), spring (43 and 40%), and summer (37 and 35%) were similar. Deer scored lower (17–28%) than human and livestock at every season. The DA was revised using results from a misclassification analysis to provide a perspective of the effect caused by low antibiotic resistance and a more realistic determination of the fecal source rates at Turkey Creek. The revision increased livestock rates by 13–14% (0.04 ≤ P ≤ 0.06), and decreased human and deer by 6–7%. Negative misclassification into livestock was significant (0.04 ≤ P ≤ 0.06). Low antibiotic resistance showed the greatest effect in this category.     

MnFe2O4磁性纳米棒非均相Fenton催化降解水中四环素的研究

采用水热合成法成功制备出MnFe₂O₄磁性纳米棒（s-MnFe₂O₄）,并考察了商品化的Fe₃O₄、MnFe₂O₄和合成的s-MnFe₂O₄纳米棒这3种磁性纳米颗粒作为非均相Fenton催化剂降解水中四环素抗生素的性能.同时,采用X射线衍射（XRD）、透射电镜（TEM）、N₂吸附-脱附、振动样品磁强计（VSM）及X射线光电子能谱（XPS）等技术对催化剂的理化性质进行了表征.非均相Fenton催化降解四环素的结果表明,s-MnFe₂O₄具有最高的催化活性,反应180 min,四环素的去除率可以达到87.6%,TOC的去除率达到47.5%.自由基捕获试验证实了羟基自由基（·OH）是非均相Fenton氧化过程中的主要活性物种.s-MnFe₂O₄磁性纳米棒的高催化活性归因于其表面拥有较高含量的Mn³⁺和Fe²⁺物种,它们的存在能加速界面电子的转移效率,从而促进·OH的生成.合成的s-MnFe₂O₄催化剂具有良好的稳定性,循环使用6次,四环素的去除率仅从87.6%降低到80.2%,且氧化过程中活性组分的流失很少.     

铁锰复合氧化物滤料去除地下水中四环素的效能

以化学挂膜成熟运行5a的铁锰复合氧化物滤料为研究对象,利用静态与连续流柱实验相结合的方式,探究了该滤料去除四环素的效果与机理.结果表明,去除过程符合准二级反应动力学模型;且滤料质量越大,初始浓度越高,对四环素去除的效果越好;当水中共存阳离子浓度为0.01mol/L时,Mg²⁺抑制四环素的去除,而Ca²⁺、K⁺对四环素的去除过程无显著影响.连续流柱实验与发光细菌毒性检测分析,表明,铁锰氧化物滤料对四环素去除效果显著高于石英砂,且铁锰复合氧化物滤料去除四环素后急性毒性降低.此外,机理探究实验结果证实了铁锰复合氧化物滤料去除四环素是吸附与氧化的过程.     

裂解温度和离子强度对不同来源生物炭胶体释放行为的影响

近年来环境中生物炭胶体形成受到广泛关注,它是生物炭在环境中物理分解作用的重要过程,对污染物迁移有着重要影响.然而,目前对生物炭胶体释放过程和影响因素的研究甚少,人们对生物炭胶体释放机理的认识还很有限.本研究以小麦秸秆和花生壳为生物质来源,系统地探讨了生物炭的裂解温度（300~700 ℃）和溶液离子强度（0.1~10 mmol·L^-1）对生物炭胶体产率的影响.结果表明,随着裂解温度的升高,生物炭的耐磨性增强,且在较高的裂解温度下（≥500 ℃）花生壳生物炭的耐磨性显著强于小麦秸秆生物炭.生物炭的胶体产率受到生物质来源和裂解温度的显著影响,花生壳生物炭的胶体产率低于小麦秸秆生物炭,高温裂解（≥600 ℃）生物炭的胶体产率显著低于中低温裂解生物炭.在相同溶液离子强度下,生物炭胶体产率与其亚微米级碎片率呈显著正相关（p<0.05）,即生物炭中亚微米级碎片率越高,生物炭胶体产率越高.当溶液离子强度从1 mmol·L^-1增加到10 mmol·L^-1时,两种来源生物炭的胶体产率均显著降低,其降低的程度因生物炭裂解温度而异,其中低温裂解（300 ℃）生物炭的胶体产率降低了11.1%~11.2%,中高温裂解（≥ 500 ℃）生物炭的胶体产率降低了60.0%~97.2%.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

基于边介数的省域生态廊道构建方法优化

我国城市建设和生态保护工作均对土地资源有大量需求,二者之间的矛盾在经济优先发展区表现尤为明显.为了有效地改善生态环境,管控土地利用并引导其变化发展,需要建设具备不可替代特征的省域生态廊道.最小累积阻力模型（minimum cumulative resistance,MCR）是识别生态廊道最常用、有效的模型,但在应用于省域尺度时,MCR模型识别的潜在廊道路由存在冗余的问题.因此,通过引入网络科学中的边介数指数（edge-betweenness）对MCR模型进行优化,计算潜在廊道路由的边介数指数值,选取出其中最为重要和简明的结构来连通生态源地,即提取潜在路由中的骨干路由（backbone route）和关键战略点（key strategic point）作为不可替代的结构来指导省域生态廊道建设.将优化后的MCR模型应用于广东省,构建了全长5 493 km的省域生态廊道,其中包含生态源地20处,关键战略点11个,骨干生态廊道29条.骨干路由与关键战略点构成的不可替代省域生态廊道（irreplaceable provincial corridor）能够实现"廊道数量和占地面积最少、连通性基本不变"的目标.研究显示,边介数能够对潜在路由进行优化筛选,识别出维护省域生态安全的关键结构;不可替代生态廊道能够指导省域生态规划和土地空间的发展利用,并为更高水平的生态安全环境提供了演进的基础;同时也为土地资源紧张的地区提供了建设生态廊道的参考与依据.      

芳纶纤维对飞机尾翼结构抗鸟撞性能影响研究

目的研究飞机尾翼结构采用芳纶纤维复合材料的抗鸟撞性能。方法根据芳纶纤维夹芯和芳纶纤维层合板两种飞机尾翼前缘构型,分别建立有限元模型进行仿真计算,分析两种构型鸟撞后的损伤和变形,并对两种构型进行抗鸟撞性能研究试验。结果芳纶夹芯前缘构型前缘凹陷,前梁没有破裂;芳纶层合板前缘构型前缘破裂,前梁有破损。试验结果与仿真分析结果高度吻合。结论芳纶夹芯前缘构型比芳纶层合板前缘构型具有更好的抗鸟撞性能。芳纶纤维层合板构型会造成前缘蒙皮变形过大,前梁腹板破损,导致飞机鸟撞后维修成本较高。