‘Emulsion locks’ for the containment of hydrocarbons during surfactant flushing

Reversible double water in oil in water (W/O/W) emulsions were developed to contain subsurface hydrocarbon spills during their remediation using surfactant flushing. Double emulsions were prepared by emulsifying CaCl₂ solutions in canola oil, and subsequently by emulsifying the W/O emulsions in aqueous sodium alginate solutions. The formation of double emulsions was confirmed with confocal and optical microscopy. The double emulsions reversed and gelled when mixed with the surfactants sodium dodecyl sulfate (SDS) and cocamidopropyl betaine (CPB). Gels can act as ‘emulsion locks’ to prevent spreading of the hydrocarbon plume from the areas treated with surfactant flushing, as shown in sand column tests. Shear rheology was used to quantify the viscoelastic moduli increase (gelation) upon mixing the double emulsion with SDS and CPB. SDS was more effective than CPB in gelling the double emulsions. CPB and SDS could adsorb at the interface between water and model hydrocarbons (toluene and motor oil), lowering the interfacial tension and rigidifying the interface (as shown with a Langmuir trough). Bottle tests and optical microscopy showed that SDS and CPB produced W/O and O/W emulsions, with either toluene or motor oil and water. The emulsification of motor oil and toluene in water with SDS and CPB facilitated their flow through sand columns and their recovery. Toluene recovery from sand columns was quantitated using Gas-Chromatography Mass-Spectroscopy (GC-MS). The data show that SDS and CPB can be used both for surfactant flushing and to trigger the gelation of ‘emulsion locks’. Ethanol also gelled the emulsions at 100 mL/L.     

壳聚糖/PVA微粒上Cu2+的吸附平衡与动力学

采用粒径＜200μm、在酸碱介质中溶胀率小且能稳定存在的壳聚糖/PVA微粒对Cu2+的吸附进行了研究,结果表明,在pH 6,室温条件下,其饱合吸附量达56.0mg/g,随温度升高,吸附量降低.通过计算不同温度下各热力学参数△G0、△H0和△S0,证实该吸附为自发的放热过程.对实验数据运用相关数学模型拟合,显示等温吸附平衡符合Langmuir模型,吸附过程动力学更适合二级反应,被吸附在壳聚糖/PVA微粒上的Cu2+,可被0.01mo/L的EDTS或HNO3溶液快速地脱附出来,其洗脱率分别为85.3%和65.9%.     

Possible Utilization of Silica Gel Sludge for the Removal of Phenol from Aqueous Solutions: Laboratory Studies

This paper discusses the adsorption capacity of silica gel sludge for phenol removal from aqueous solution. Kinetic experiments showed that phenol adsorption was completed after 2 h. Adsorption isotherms were measured for phenol from aqueous solution onto silica gel sludge under various pHs and temperatures. Results showed that the adsorption capacities for phenol was increased as pH decreased from 6.5 to 2. Temperature also was found to affect the adsorption isotherm. As temperature increases from 30 to 50°C, the adsorption capacity increases. The adsorption equilibrium of phenol on silica gel sludge was described by the linear Freundlich and Langmuir models. Furthermore, results showed that the isotherm parameters fit both linearized Langmuir and Freundlich adsorption isotherms. The Freundlich and Langmuir parameters at optimum pH was found as K _f=2.89, 1/n=0.23 and K _d=22.0, q _m=7.98, respectively. Whereas, for those at optimum temperature it was observed as K _f=2.87, 1/n=0.16 and K _d=20.93, q _m=7.91, respectively.     

西辽河流域沙土的氨氮解吸行为研究

采用小型回填式土柱淋溶实验方法研究了西辽河流域沙土的氨氮解吸行为。结果表明,西辽河流域沙土的氨氮解吸行为符合Langmuir和Freundlich解吸等温式;沙土氨氮解吸比率Dr在0.44～0.99之间,平均为0.75,解吸迟滞性指数TⅡ在0.05～0.65之间,平均为0.29,沙土对氨氮的解吸迟滞性较强,解吸可逆性较弱。被吸附的氨氮解吸淋失的环境风险较小;沙土氨氮解吸比率Dr与土壤有机质含量、粘粒含量和粗粘粒含量呈极显著负相关,影响程度顺序为:有机质含量>粗粘粒含量>粘粒含量;解吸分配系数k和解吸迟滞性指数与土壤有机质含量分别呈极显著和显著正相关,与粘粒含量和粗粘粒含量没有相关性;草地、农田和林地结构由于土壤有机质和团聚体含量较高,氨氮解吸迟滞性较强,氨氮流失的环境风险较小,沙荒地结构氨氮流失的环境风险较大。     

Biosorption of nickel(II) from aqueous solution by Aspergillus niger: Response surface methodology and isotherm study

In the present study, the effects of biosorbent Aspergillus niger dosage, initial solution pH and initial Ni(II) concentration on the uptake of Ni(II) by NaOH pretreated biomass of A. niger from aqueous solution were investigated. Batch experiments were carried out in order to model and optimize the biosorption process. The influence of three parameters on the uptake of Ni(II) was described using a response surface methodology (RSM) as well as Langmuir and Freundlich isotherm models. Optimum Ni(II) uptake of 4.82 mg Ni(II) g⁻¹ biomass (70.30%) was achieved at pH 6.25, biomass dosage of 2.98 g L⁻¹ and initial Ni(II) concentration of 30.00 mg L⁻¹ Ni(II). Langmuir and Freundlich were able to describe the biosorption isotherm fairly well. However, prediction of Ni(II) biosorption using Langmuir and Freundlich isotherms was relatively poor in comparison with RSM approaches. The biosorption mechanism was also investigated by using Fourier transfer infrared (FT-IR) analysis of untreated, NaOH pretreated, and Ni(II) loaded A. niger biomass.     

Adsorption of glyphosate on Brazilian subtropical soils rich in iron and aluminum oxides

Abstract

We investigated the adsorption of glyphosate onto five subtropical soils of Paraná and São Paulo states, Brazil, a region of intense agricultural activities, aiming at the determination of kinetic and isotherm adsorption parameters which enable the evaluation of the potential leaching of the herbicide. The adsorption was fast, being described by the pseudo-second order and intraparticle diffusion models, thus suggesting that mixed mechanisms are involved. The Oxisol containing the highest concentrations of metal oxides (209.5?g kg^?1 Fe₂O₃ and 160.2?g kg^?1 Al₂O₃) was the sample with the highest rate constant, indicating the adsorption sites are readily available. All the soils are rich in aluminum and iron oxides, explaining the Freundlich coefficients (K_F) between 642 and 1360?mg^1-1/n kg^?1 L^1/n, which are higher than most of the coefficients described for other soils around the world. The maximum desorption (15% of the adsorbed amount) was observed for the Oxisol. For the other soils, desorption ranged from 2 to 7%. These results suggest that the leaching of free glyphosate to nearby surface and groundwaters is unlikely unless excessive doses are used. The adsorption parameters are useful for managing the right doses applied to the crops, thus avoiding contamination of adjacent areas.     

Effect of particle size on CO adsorption and thermodynamic analysis

The liquid nitrogen adsorption method was used to characterize the pore structure of non-cohesive coal in the 061,404 working face of the Lingxin coal mine. The amount of specific surface area of micropores in the sample continuously rose as particle sizes reduced. The volumetric method was used to measure the CO isothermal adsorption curves of three samples (sample I, 0.425–0.25 mm, sample II, 0.18–0.25 mm, and sample III, 0.15–0.18 mm). The experimental results were fitted by the Langmuir model. According to the experimental results, it was conducive to CO adsorption with the conditions of high pressure and low-temperature. The decrease in grain diameter increased the number and volume of micropores in the sample, which improved the adsorption capacity of the sample. In addition, according to the adsorption data, the CO adsorption thermodynamics of three samples were analyzed, including surface potential (Ω), Gibbs free energy change (ΔG) and entropy change (ΔS). The results demonstrated that CO adsorption by coal was a spontaneous process. Sample III has the most substantial adsorption capacity, whereas the sample I has the weakest adsorption capacity.     

Platinum (IV) recovery from chloride solution by functionalized acrylic copolymers

Two acrylic adsorbents with different morphological structures and bearing amidoethylenamine and thiol groups were obtained and used for platinum sorption from chloride solution by the batch method. Physico-chemical parameters that influence adsorption such as initial Pt(IV) concentration, stirring time, pH, and adsorbent amount were investigated. The thermodynamic parameters of Pt(IV) sorption on the synthesized adsorbent were also evaluated based on Langmuir and Freundlich isotherms. Thermodynamic parameters estimated from Langmuir constants indicated that the adsorption is spontaneous, exothermic and there is a disordered state at the molecular level. The models used to analyze the sorption rate led to the conclusion that the most important step in the sorption of Pt(IV) could be both particle diffusion and chemical reaction of [PtCl₆]⁻ with amine functional groups. Thus, both the ion exchange and complex formation mechanisms can occur via nitrogen atoms in the recovery of Pt(IV) on the studied adsorbent.     

Heavy-metal adsorption by non-living biomass

The adsorption of some heavy metals onto the walls of harvested, washed, and dried non-living biomass cells of different Pseudomonas strains was studied at optimum experimental conditions using a simplified single component system. The Langmuir adsorption model was found to be a suitable approach to describe the system via multi-step processes. Isotherms measured at 30.0°C and pH 5.5 with [M]_total = 10-100 mM for tight, reversible Cr⁶⁺(aq), Ni²⁺(aq), Cu²⁺(aq) and Cd²⁺(aq) binding by the cell walls of the investigated biomass fit the Langmuir model and give the pH-independent stoichiometric site capacities ν_i and equilibrium constants K_i for metal binding at specific biomass sites i = A, B, C, and D. Tight binding sites A, B, and D of the non-living biomass are occupied by Cr^VI, sites A and C by Ni^II, sites A and D by Cd^II, and only site B by Cu^II. It is concluded that ν_i is a stoichiometric parameter that is independent of the magnitude of K_i for binding site i and that the studied heavy metals selectively and tightly bind at different biomass sites.