Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

生活垃圾生物处理的研究与展望

综述了国内外生活垃圾生物处理的研究进展和目前生活垃圾微生物研究水平，以及生活垃圾处理发展趋势与新动向，在此基础上提出了生活垃圾处理的建议和展望。     

厌氧-混凝工艺处理造纸厂终端废水试验研究

本文报告了用厌氧 -混凝工艺处理造纸厂终端废水的实验情况 ,在最佳实验条件下 ,废水从CODcr80 6 . 7m g/ L、BOD52 10 . 5 m g/ L、SS2 15 . 7m g/ L、OD4 650 . 35 0降至 CODcr6 1. 5 m g/ L、BOD52 7. 4m g/ L、SS17.3mg/ L、OD4 650 .0 11。实验结果表明对造纸厂终端废水的治理 ,本工艺是很有实用价值的一种方法     

A2/O工艺处理氨纶废水的应用研究

介绍了采用厌氧-缺氧-接触氧化(即A2/O)组合工艺处理氨纶生产废水的流程和设计参数,通过近半年的调试数据,反应季节对A2/O组合工艺处理氨纶生产废水的影响和可行性。提出运行过程中需要控制的参数,提供设计和运行参考。     

ABR反应器的设计

类似于多个UASB反应器串联起来运行的ABR反应器具有多种其它反应器不具备的优点，在处理化工颜料黄高盐生产废水的工程中，结合将高效复合微生物技术用于厌氧水解一连续曝气生化工艺取得成功；对ABR反应器而言，正确的设计参数是工程运行成功的保证。     

UAMR中温处理高浓度啤酒废水研究

研究了上流厌氧复合反应器（ＵＡＭＲ）中温处理高浓度啤酒废水的工况，并对反应器运行性能的影响因素进行了分析。试验结果表明，在３５℃时，当进水有机容积负荷为８～１２ｋｇＣＯＤ／ｍ＾３·ｄ，水力停留时间ＨＲＴ〉０．４ｄ时，ＣＯＤ去除率可达到８０％以上，沼气ＣＨ４含量为７０．３％，反应器平均生物积累产率为０．０５０４ｋｇｖｓｓ／ｋｇＣＯＤ。     

活性污泥外循环SBR系统循环污泥释磷能力研究

本试验以HAc作为厌氧释磷的碳源有机物，以SBR系统外循环污泥作为研究对象，探索外循环活性污泥的厌氧释磷能力和获取高浓度富磷污水的途径，试验表明：厌氧过程中聚磷菌吸收HAc和释放PO4^3 的分子比为1：1。即吸收2．06mgHAc-COD将诱导1mgP释放，单位时段比污泥的平均释磷速率Vp=6.54.t^0.76，理想的厌氧时间为60－180min，减少循环污泥释磷系统的反应容积可以提高富磷污水磷酸盐的浓度。     

水解酸化—厌氧工艺处理高浓度抗生素废水研究

研究了水解酸化与厌氧消化组合工艺处理高浓度抗生素废水,结果表明,水解酸化反应器最大CODcr容积负荷达到 16.84kg/m3·d,复合厌氧反应器CODcr容积负荷达到8.57kg/m3·d;系统进水SO42-浓度为1325mg/L,CODcr/SO42-值最低达到 3;CODCr与SO42-总去除率分别为75.5％和95.2％,对各种抑制物质和冲击负荷表现出很好的适应性。     

高浓度阿维菌素生产废水治理与资源回收技术研究

采用预处理一厌氧水解－二段接触氧化工艺处理阿维菌素废水，在厌氧段停留时间为１０ｈ，好氧段停留时间为６ｈ条件下，厌氧好氧段ＣＯＤ总去除率达９１％，     

活性炭厌氧流化床处理毒性有机废水存在的问题与对策

活性炭厌氧流不处理毒性有机废水存在问题，对含有活性炭能吸附而生物难降解成份的废水，通过定期替换少量活性炭、能维持工艺的稳定运行。