饱和粉末活性炭电化学再生研究

采用电化学再生法对吸附处理染料废水产生的饱和粉末活性炭(PAC)进行再生,以NaCl为电解质,考察了电源类型、pH、再生时间、电压和NaCl浓度对活性炭再生率的影响,并对活性炭表面酸性含氧官能团进行测定。结果表明:(1)在pH=1、直流电压为6V、NaCl为6g/L、再生90min的最佳条件下,采用单室反应器,饱和PAC再生率达到59.09%。(2)电极循环伏安曲线结果表明,饱和PAC电极表面发生氧化反应,与主电极直接和间接氧化共同作用,使活性炭表面吸附的污染物降解。活性炭表面酸性含氧官能团滴定和红外光谱测试结果进一步表明,电化学再生法使活性炭表面基团得到恢复。     

三维电极电Fenton氧化法处理染料废水

采用三维电极电Fenton氧化法处理实际染料废水,探究了染料废水处理效果的影响因素。实验结果表明：以钌铱镀层钛电极为阳极、不锈钢板为阴极、粉末活性炭为颗粒电极,在粉末活性炭投加量为2.0 g/L、电流密度为0.5 mA/mm²、极板间距为3 cm、pH为2.0、硫酸亚铁投加量为0.50 g/L的最优工艺条件下,反应2 h后COD、TOC、氨氮、色度的去除率达到最大,分别为62.80%、41.15%、42.48%和95.00%;粉末活性炭作为颗粒电极可使染料废水COD去除率提高18个百分点;重复使用10次的处理效果与第2次基本持平。     

镍掺杂二氧化钛光催化剂的制备与光催化性能研究

利用溶胶-凝胶法制备了镍掺杂的二氧化钛,采用紫外可见分光光度计、傅里叶红外分光光度计、X衍射仪(XRD)、扫描电镜(SEM)等测试手段对结果进行了表征。表征结果表明在550℃下煅烧的产物主要是锐钛型二氧化钛,镍的掺杂使得二氧化钛的紫外可见反射光谱明显红移,且镍掺杂二氧化钛的粒度减小,团聚程度下降。以活性艳蓝KN-R为模型降解目标物,通过比较镍掺杂二氧化钛、纯二氧化钛以及标准P25二氧化钛的光催化性能发现镍掺杂二氧化钛的光催化活性最好。当钛酸正丁酯/乙醇比为1:25;钛酸正丁酯/冰乙酸比为1:1;钛酸正丁酯/硝酸镍比为1 000:3;煅烧温度为550℃,煅烧时间为2 h时,镍掺杂二氧化钛的光催化效率最高,达到73.3%。     

适于工业应用的TiO2纳米管的阳极氧化法制备

通过阳极氧化法制备了适于工业应用的大尺寸二氧化钛纳米管阵列.考察了电极形状和面积、氧化电压、氧化时间、预处理等因素对阳极氧化法制备二氧化钛纳米管阵列形貌的影响.结果显示,电极形状对纳米管的制备没有影响;阳极氧化前打磨与否对纳米管也没有影响;氧化电压、氧化时间和电极面积对纳米管的影响较大,只有在合适的电压和时间下才能制成纳米管阵列.电极面积影响电流密度,从而影响纳米管的形貌,试验中电极最大面积为360cm2.通过试验得出工业化制备二氧化钛纳米管阵列的最佳条件是电压20V,电解时间30min,反应前不用进行打磨.实验结果显示制成的纳米管阵列对强酸强碱的耐受力强,完全可以适应工业化废水的pH变化.     

氧气热处理的TiO2纳米管阵列光电催化降解亚甲基蓝的研究

采用原位阳极氧化法在Ti基底上制备了高度有序的TiO2纳米管阵列薄膜,SEM图像表明TiO2纳米管定向排列整齐,分布均匀,其管径范围在70～100 nm.XRD结果证明,阳极氧化法制备的TiO2纳米管为无定型晶型,经退火后为具有良好光催化活性的锐钛矿型.以亚甲基蓝（methylene blue）为目标物研究了TiO2纳米管光电催化性能及影响因素,结果表明,以0.1 mol/L NaCl为电解质,在氧气热处理气氛下,外加偏压为0.5 V、pH=3.25、光照强度为1 000μW/cm2、纳米管薄膜表面积为2 cm×2 cm且MB初始浓度为10 mg/L的条件下,TiO2纳米管阵列薄膜光电催化降解MB的降解效率可达99.56%.电化学阻抗谱分析显示,光电催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

N掺杂TiO_2光催化还原地下水中硝酸盐

以硫酸钛为前驱体,采用水热沉淀法制备TiO2光催化剂,采用扫描电子显微镜(SEM)、X-射线能谱(EDS)、X-射线衍射(XRD)、傅立叶红外光谱仪(FTIR)和光电子能谱仪(XPS)进行表征和分析,考察了硫酸钛浓度、焙烧温度对光催化还原水中硝酸盐活性的影响.结果表明,制备的催化剂为掺杂N的锐钛矿型TiO2.硫酸钛浓度为0.5mol.L-1、焙烧温度为400℃时制备的催化剂活性最佳,反应120min后,硝酸盐转化率为95.8%,中间产物NO--N浓度为0.17mg·mL-1,副产物NH+-N浓度为1.52mg·mL-1.     

载2,4-DCP粉末活性炭微波再生的影响因素

2,4-DCP(2,4-二氯苯酚)是一种具有代表性的氯酚类化合物,在我国和欧美等国的饮用水水质标准中,氯酚类化合物都被列为优先控制污染物。实验以2,4-DCP溶液作为给水中难降解有机物的模拟水样,使用粉末活性炭(PAC)对其吸附至饱和后进行微波辐照再生,探讨了影响活性炭再生效果的诸多因素。以N2为载气的正交实验结果表明:在微波功率为800 W,再生时间为3 min,载气流量为0.6 L/min的控制条件下可得到最佳的再生效果;另选CO2为载气对活性炭再生进行比照实验,结果表明CO2载气的再生效果略优于N2,具有活化作用。     

Influences of working pressure on properties for TiO2 films deposited by DC pulse magnetron sputtering

TiO2 films were deposited at room temperature by DC pulse magnetron sputtering system.The crystalline structures,morphological features and photocatalytic activity of TiO2 films were systematically investigated by X-ray diffraction (XRD),atomic force microscopy and ultraviolet spectrophotometer,respectively.The results indicated that the working pressure was the key deposition parameters influencing the TiO2 film phase composition at room temperature,which directly affected its photocatalytic activity.With increasing the working pressure,the target self-bias decreases monotonously.Therefore,low temperature TiO2 phase (anatase) could be deposited with high working pressure.The anatase TiO2 films deposited with 1.4 Pa working pressure displayed the highest photocatalytic activity by decomposition of Methyl Orange solution,which the degradation rate reached the maximum (35%) after irradiation by ultraviolet light for 1 h.     

Synthesis, characterization, and adsorption performance of Pb（Ⅱ）-imprinted polymer in nano-TiO2 matrix

Surface ion-imprinted in combination with sol-gel process was applied to synthesis a new Pb(II)-imprinted polymer for selective separation and enrichment of trace Pb(II) from aqueous solution. The prepared material was characterized by using the infrared spectra, X-ray di ractometer, and scanning electron microscopy. The batch experiments were conducted to study the optimal adsorption condition of adsorption trace Pb(II) from aqueous solutions on Pb(II)-imprinted polymer. The equilibrium was achieved in approximately 4.0 h, and the experimental kinetic data were fitted the pseudo second-order model better. The maximum adsorption capacity was 22.7 mg/g, and the Langmuir equation fitted the adsorption isotherm data. The results of selectivity experiment showed that selectively adsorbed rate of Pb(II) on Pb(II)-imprinted polymer was higher than all other studied ions. Desorption conditions of the adsorbed Pb(II) from the Pb(II)-imprinted polymer were also studied in batch experiments. The prepared Pb(II)-imprinted polymer was shown to be promising for the separation and enrichment of trace Pb(II) from water samples. The adsorption and desorption mechanisms were proposed.     

Au/SnO_2/TiO_2催化氧化CO性能的研究

通过煅烧制备TiO2,用浸渍法负载SnO2,沉积沉淀法负载Au,制备不同SnO2含量的Au/SnO2/TiO2催化剂。采用BET、SEM、XRD等手段对催化剂样品进行表征并考察煅烧温度、SnO2的添加量等对Au/SnO2/TiO2催化剂催化CO氧化活性的影响。结果表明:Au/SnO2/TiO2催化活性比Au/TiO2明显提高;海绵钛在400℃煅烧后负载10%SnO2和1%的Au催化活性较好,在124℃左右能使气体中含量为2.94%的CO基本完全转化。