臭氧氧化—湿式钙法吸收工艺对烟气的同时脱硫脱硝

采用臭氧氧化—湿式钙法吸收工艺对模拟烟气进行同时脱硫脱硝处理。O₃于150 ℃下具有较高的热稳定性,可将NO氧化为高价态氮氧化物,且NO氧化率随n（O₃）∶n（NO）的增大而逐渐提高。烟气中SO₂和H₂O的存在对NO氧化率的影响不大。O₃对SO₂的氧化率较低,约为5%。3%（w）石灰石浆液对SO₂的吸收率接近100%,NO_x吸收率随n（O₃）∶n（NO）的增大而逐渐提高,当n（O₃）∶n（NO）为1.6时NO_x吸收率可达约65%。SO₂能促进吸收液对NO_x的脱除。石灰石浆液中加入0.2%（w）的（NH₄）₂SO₃或Na₂SO₃后NO_x吸收率可达约85%或82%,且吸收率随添加剂加入量的增加而提高,添加（NH₄）₂SO₃的NO_x吸收率略高于添加Na₂SO₃。     

CeO2/TiO2纳米管催化剂脱硝性能研究

利用废气中本身含有的CO催化还原烟气中的NO_x,可以实现以废治废。采用TiO₂纳米管负载CeO₂,制备CeO₂/TiO₂纳米管催化剂,并对其进行了SEM表征及影响因素实验。实验结果表明：在n（Ce）∶n（Ti）=3∶7、焙烧温度500 ℃、焙烧时间3 h时制备的CeO₂/TiO₂纳米管催化剂形貌较好,表面颗粒分布相对均匀;反应温度400~600 ℃时NO脱除率达98%;该催化剂具有一定的抗氧性能;当n（SO₂）∶n（NO）=（1∶2）~（2∶1）时,NO脱除率仍然在95%以上。     

半干法脱除球团烟气中的SO2及Hg0

采用钙基吸收剂及复合氧化剂半干法脱除模拟球团烟气中的SO_2及Hg~0,考察了多因素条件对吸收效果的影响。实验结果表明,在以NaClO和NaClO_2为复合氧化剂、 NaClO与NaClO_2体积比1∶0.5、复合氧化剂质量分数3%、反应温度110℃、钙基吸收剂质量3.0 g、模拟烟气进气流量1.2 L/min的条件下,SO_2和Hg~0的脱除率分别为98%和93%,证明钙基吸收剂与复合氧化剂对污染物球团烟气中的SO_2和Hg~0有良好的脱除作用。     

某电厂600MW火电机组脱硫增容改造方案探讨

按照国家环保部文件要求，大唐集团河北某电厂600 MW机组湿法脱硫系统需进行增容改造。该电厂根据实际情况，归纳了3种可行的脱硫增容改造方案，即原吸收塔增加喷淋层和高度、双吸收塔串联、双吸收塔双循环，阐述了各自的技术特点，结合性能保证、工程投资、施工周期等影响因素，比较了各方案的优缺点。经过对比和论证，双吸收塔方案比单吸收塔方案更适合于本次工程改造。     

γ-Al2O3负载多金属复合催化剂选择性催化还原烟气脱硝

以γ-Al₂O₃作为载体，先后负载CeO₂，MnC₂O₄，Fe（NO₃）₃，CrO₃，Ni（NO₃）₂，NH₄VO₃等多种金属组分制备γ-Al₂O₃负载多金属复合催化剂，并用于模拟烟气的选择性催化还原脱硝。通过SEM和XRD技术对催化剂进行了表征。表征结果显示：Fe，Mn，Cr的添加能增加催化剂的低温催化活性、提高催化剂的N₂选择性;γ-Al₂O₃对活性金属氧化物的负载效果良好。实验结果表明：各金属化合物的最佳加入量为 w（MnC₂O₄·2H₂O）=20%，w（Fe（NO₃）₃·9H₂O）=15%，w（CrO₃）=10%，w（Ni（NO₃）₂·6H₂O）=5%，w（NH₄VO₃）=10%，w（CeO₂）=5%，w（γ-Al₂O₃）=35%;以在最佳正交实验条件下制得的γ-Al₂O₃负载多金属复合物为催化剂，在脱硝反应温度为205 ℃的条件下，NO转化率为96.7%;γ-Al₂O₃负载多金属复合催化剂经5次重复使用，NO转化率仍可稳定在94%左右。     

TSLCDM长袋低压脉冲布袋除尘器及其应用

为了使电炉烟气治理过程中污染源的排放达到国家排放标准,提出一种TSLCDM长袋低压脉冲除尘器(简称TSLCDM除尘器)。通过对该除尘器结构、除尘原理以及不同工况下除尘效率和过滤阻力的分析,得到该除尘器的除尘效率>99.9%,压力损失<1200 Pa,最终排出的烟气含尘质量浓度约5.54 mg/m3,满足了国家的超低排放要求,以泉州某公司电炉项目除尘系统为研究对象,证明了该新型脉冲布袋除尘器在电炉烟气治理除尘系统的应用效果,具有很好的经济和环境效益。     

非烟气工况下常规烟塔与改造烟塔内部结构的比较

根据流体力学理论,基于Fluent6.3.26计算平台,对常规冷却塔和改造后的排烟冷却塔进行了三维内部流场的模拟。分析非烟气工况下,两塔内部烟道布置对气流的影响,为进一步研究在工况条件下烟气、水蒸气塔内扰流与湿热蒸汽抬升作用提供理论基础。验证了改造烟塔内部烟道布置的优越性,对排烟冷却塔结构优化有一定的指导意义。     

火电湿法烟气脱硫流程优化的实现方案研究

在给定脱硫流程模拟优化参数的情况下,尝试了基于DCS系统和基于OA局域网的两种优化控制改进方案,后一种方案解决了优化控制系统的安全性、稳定性、扩展性、易管理等问题。同时采用该控制系统的3号脱硫系统的控制效果最佳,且脱硫效率循环浆液泵功率比随着操作方式相近度的提高而呈递增趋势。     

Synthesis, characterization and experimental investigation of Cu-BTC as CO2 adsorbent from flue gas

Porous Cu-BTC material was synthesized by the solvothermal method. Powder X-ray diffraction (PXRD) was used to test the phase purity of the synthesized material and investigate its structural stability under the influence of flue gas components. The thermal stability of the material was determined through thermal gravimetric (TG) analysis. Scanning electron microscopy (SEM) was employed to study the microstructure of the material. Cu-BTC was demonstrated not only to have high CO₂ adsorption capacity but also good selectivity of CO₂ over N₂ by means of packed bed tests. The adsorption capacity of Cu-BTC for CO₂ was about 69 mL/g at 22°C. The influence of the main flue gas components on the CO₂ capacity of the material were discussed as well.     

Operating condition influences on PCDD/Fs emissions from sinter pot tests with hot flue gas recycling

This study was designed to clarify the influence of operating conditions on the formation and emissions of polychlorinated-pdibenzodioxins and dibenzofurans (PCDD/Fs) from a sintering process with hot flue gas recycling. A pilot scale sinter pot with simulated flue gas recycling was developed, and four key operational parameters, including temperature, oxygen content of the simulated waste flue gas, the coke rate of the sintering mixture, and the quicklime quality, were selected for exploring PCDD/Fs formation. The results showed that the temperature of the recycled flue gas had a major affect on PCDD/Fs formation, and a high temperature could significantly increase their formation during sintering. A clear linear correlation between the temperature of recycling flue gas and PCDD/Fs emission (r = 0.93) was found. PCDD/Fs could be reduced to a certain extent by decreasing the level of oxygen in the recycled flue gas, while sintering quality was unchanged. The coke rate had no significant influence on the formation of PCDD/Fs, but the quality of quicklime used in the sintering mixture could affect not only the amount of PCDD/Fs emissions but also the sintering productivity. Compared with a benchmark sinter pot test, PCDD/Fs emissions markedly decreased with improvements to quicklime quality. However, the reduction in PCDD/Fs emissions realized by using high-quality quicklime was limited by the temperature of the inlet gas. The highest reduction achieved was 51% compared with conventional quicklime when the temperature of the inlet gas was 150°C.