| 基于仿真的新建污水处理厂工艺参数调试 |
| |
| 引用本文： | 姚重华,王国华,谭学军,李池鸿,周炜,张辰.基于仿真的新建污水处理厂工艺参数调试[J].环境科学学报,2009,29(10):2086-2093. |
| |
| 作者姓名： | 姚重华 王国华 谭学军 李池鸿 周炜 张辰 |
| |
| 作者单位： | 1. 华东理工大学资源与环境工程学院,上海,200237
2. 上海市政工程研究设计总院,上海,200092 |
| |
| 基金项目： | 上海市科委基金(No.072312003) |
| |
| 摘 要： | 基于ASM2D模型建立了上海某新建污水厂倒置AAO流程的数学模型，并采用该厂进、出水设计数据对模型进行校正，其中，ASM2D各组分浓度分布参考文献值.同时，通过仿真计算研究了不同温度下进水流量、污泥回流比、混合液回流比及进水流量分配比对出水总化学需氧量（TCOD）、氨氮（SNH3）、总氮（TN）、总磷（TP）及总悬浮颗粒物（TSS）的影响.结果表明，研究获得的定性和定量两方面结果可供该厂在工艺参数调试中作参考.计算机仿真技术在新建污水厂工艺参数调试中的应用可以减少调试时间，降低调试费用，取得良好的经济效益与环境效益.
|
| 关 键 词： | 新建污水厂 计算机仿真 模型校正 工艺参数调试 |
| 收稿时间： | 2008/12/10 0:00:00 |
| 修稿时间： | 4/22/2009 7:47:32 PM |
Process parameter adjustment of a newly built AAO wastewater treatment plant based on ASm2D simulation |
| |
| YAO Chonghu,WANG Guohu,TAN Xuejun,LI Chihong,ZHOU Wei and ZHANG Chen.Process parameter adjustment of a newly built AAO wastewater treatment plant based on ASm2D simulation[J].Acta Scientiae Circumstantiae,2009,29(10):2086-2093. |
| |
| Authors: | YAO Chonghu WANG Guohu TAN Xuejun LI Chihong ZHOU Wei and ZHANG Chen |
| |
| Institution: | School of Resource and Environment, East China University of Science and Technology, Shanghai 200237,Shanghai Municipal Engineering Design General Institute, Shanghai 200092,Shanghai Municipal Engineering Design General Institute, Shanghai 200092,School of Resource and Environment, East China University of Science and Technology, Shanghai 200237,Shanghai Municipal Engineering Design General Institute, Shanghai 200092 and Shanghai Municipal Engineering Design General Institute, Shanghai 200092 |
| |
| Abstract: | An inverse AAO process in a newly built wastewater treatment plant was modeled based on ASM2D. The model was calibrated by using the influent and effluent data in the design specifications of the plant, and the component concentrations of ASM2D were chosen from the literature. The simulation focused on the influence of flow rate, external recycle rate, internal recycle rate, ratio of flows into different reaction tanks, total COD (TCOD), ammonia nitrogen (SNH3), total nitrogen (TN), total phosphorus (TP), and total suspended particles (TSS). The qualitative and quantitative results may be used as a reference for process parameter adjustment in the newly built plant. A demand for thousands of municipal wastewater treatment plants of different sizes has appeared in China, and strengthening the application of modeling and simulation is very helpful for reducing time and cost in process parameter adjustment. |
| |
| Keywords: | newly built wastewater treatment plant computational simulation model calibration process parameter adjustment |
| 本文献已被 万方数据 等数据库收录！ |
| 点击此处可从《环境科学学报》浏览原始摘要信息 |
| 点击此处可从《环境科学学报》下载免费的PDF全文 |
|
