TiO2/H2O2/UV和TiO2/O3/UV降解对氯苯甲酸和喹啉的试验研究

主要叙述TiO2/H2O2/UV和TiO2/O3/UV体系降解对氯苯甲酸(4-CBA)和喹啉的试验研究.研究表明,(1)在TiO2/H2O2/UV体系里目标物降解速度先随过氧化氢投加量的增加而提高,但超过一定浓度之后便开始下降;(2)在TiO2/O3/UV体系中,目标降解物的反应速度都非常快,且臭氧浓度高的时候降解速度更快;(3)二氧化钛催化剂在TiO2/O3/UV体系中作为积极因素有助于提高反应速率,而在TiO2/H2O2/UV体系是消极因素,会降低反应速率.     

UV/H2O2/Fe-FeOxH2x-3和UV/H2O2工艺降解水中富里酸的研究

采用硼氢化钠还原法制备核-壳结构的Fe-FeOxH2x-3复合材料,研究了富里酸在UV/H2O2和UV/H2O2/Fe-FeOxH2x-3两种不同反应体系下的降解情况。结果表明,核-壳结构Fe-FeOxH2x-3的存在,提高了UV/H2O2降解富里酸的反应速率,TOC去除达到84%。采用XAD树脂吸附法对反应前后的富里酸进行化学分级表征,结果表明,富里酸经反应后憎水酸（HoA）、弱憎水酸（WHoA）和憎水中性物质（HoN）都有所减少,进而转化为亲水性物质（HiM）;用超滤膜法对富里酸进行物理分级表征,考察了富里酸在反应前后分子量分布的变化情况。同时,富里酸经过反应后生成的中间产物降低了三氯甲烷生成趋势。     

Comparative study of the oxidation of atrazine and acetone by H2O2/UV, Fe(III)/UV, Fe(iii)/H2O2/UV and Fe(II) or Fe(III)/H2O2

In this study, the rates of degradation of organic compounds by several AOPs (H₂O₂/UV, Fe(III)/UV, Fe(III)/H₂O₂/UV, Fe(II)/H₂O₂ and Fe(III)/H₂O₂) have been compared. Experiments were carried out at pH ≈ 3 (perchloric acid / sodium perchlorate solutions) and with UV reactors equipped with a low-pressure mercury vapour lamp (emission at 253.7 run). The data obtained with atrazine ([Atrazine]_o = 100 μg/L) showed that the rate of degradation of atrazine in very dilute aqueous solution is much more rapid with Fe(III)/UV than with H₂O₂/UV. Photo-Fenton process (Fe(III)/H₂O₂/UV) was found to be more efficient than H₂O₂/UV and Fe(II)/H₂O₂ for the mineralization of acetone ([Acetone]_o = 1 mM).     

臭氧与TiO2/UV协同降解对氯苯酚

利用O3／UV、TiO2／UV和O3／TiO2／UV降解对氯苯酚表明，臭氧与TiO2／UV具有明显的协同作用，如在本实验条件下降解5min后，上述3者对对氯苯酚的去除率分别为55％、10％和77%。O3／TiO2／UV协同作用的本质是由于臭氧能带走二氧化钛光致电子空穴对中的电子，从而产生了更多的羟基自由基，加速了有机物的降解。     

UV/H2O2工艺降解环丙沙星的研究

采用UV/H2O2工艺去除水体中的喹诺酮类抗生素环丙沙星（CIP）。考察了溶液pH值、H2O2投加量以及水体基质对环丙沙星降解效率的影响,分析了降解产物的生成情况。研究表明,环丙沙星的降解符合拟一级反应动力学模型。降解速率受溶液pH值的影响,酸性及中性条件,有利于环丙沙星的降解。H2O2投加量的增大,使得降解速率逐渐增大,但速率增幅逐渐变缓;最佳H2O2/环丙沙星摩尔比为2 000。实际水体中存在的NOM、NO3-,促进了单独UV作用下,环丙沙星的降解。水体中的.OH焠灭剂,抑制了UV/H2O2联合作用下,环丙沙星的降解;实际水体中的光解速率常数低于超纯水中的光解速率常数。GC-MS分析表明,UV/H2O2工艺,使环丙沙星氧化降解生成氨基乙酸、丙二酸、丙三醇和对苯二甲酸等小分子有机物。     

Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

Photochemical degradation of atrazine in UV and UV/H2O2 process: pathways and toxic effects of products

The degradation of atrazine in aqueous solution by UV or UV/H₂O₂ processes, and the toxic effects of the degradation products were explored. The mineralization of atrazine was not observed in the UV irradiation process, resulting in the production of hydroxyatrazine (OIET) as the final product. In the UV/H₂O₂ process, the final product was ammeline (OAAT), which was obtained by two different pathways of reaction: dechlorination followed by hydroxylation, and the de-alkylation of atrazine. The by-products of the reaction of dechlorination followed by hydroxylation were OIET and hydroxydeethyl atrazine (OIAT), and those of de-alkylation were deisopropyl atrazine (CEAT), deethyl atrazine (CIAT), and deethyldeisopropyl atrazine (CAAT). OIAT and OAAT appeared to be quite stable in the degradation of atrazine by the UV/H₂O₂ process. In a toxicity test using Daphnia magna, the acute toxic unit (TUa) was less than 1 of TUa (100/EC₅₀, %) in the UV/H₂O₂ process after 30 min of reaction time, while 1.2 to 1.3 of TUa was observed in the UV process. The TUa values of atrazine and the degradation products have the following decreasing order: OIET> Atrazine> CEAT≈CIAT> CAAT. OIAT and OAAT did not show any toxic effects.     

Photochemical degradation of ciprofloxacin in UV and UV/H2O2 process: kinetics, parameters, and products

Photochemical degradation of fluoroquinolone ciprofloxacin (CIP) in water by UV and UV/H₂O₂ were investigated. The degradation rate of CIP was affected by pH, H₂O₂ dosage, as well as the presence of other inorganic components. The optimized pH value and H₂O₂ concentration were 7.0 and 5 mM. Carbonate and nitrate both impeded CIP degradation. According to liquid chromatography–tandem mass spectrometry analysis, four and 16 products were identified in UV and UV/H₂O₂ system, respectively. Proposed degradation pathways suggest that reactions including the piperazinyl substituent, quinolone moiety, and cyclopropyl group lead to the photochemical degradation of CIP. Toxicity of products assessed by Vibrio qinghaiensis demonstrated that UV/H₂O₂ process was more capable on controlling the toxicity of intermediates in CIP degradation than UV process.     

Decolorizing of lignin wastewater using the photochemical UV/TiO2 process

Studies on applying the photochemical UV/TiO2 oxidation process to treat the lignin-containing wastewater for dissolved organic carbon (DOC), color and reducing A254 (the absorption at the wavelength of 254 nm) have been carried out. The data obtained in this study demonstrate that the UV/TiO2 process is effective in oxidizing the lignin thus reducing the color and DOC of the wastewater treated. The combined UV/TiO2 treatment can achieve better removal of DOC and color than the UV treatment alone. Color removal, based on American Dye Manufacture Index (ADMI) measurement, is greater than 99% if the pH is maintained at 3.0 with the addition of 1 g l(-1) TiO2. When 10 g l(-1) TiO2 is applied, the oxidation reduction potential (ORP) value is reached to result in an 88% removal of both DOC and color. A model was developed based on the variation of ORP during the photochemical reaction to simulate the decoloring process. The proposed model can be used to predict the color removal efficiency of the UV/TiO2 process.     

UV/H2O2/GAC工艺去除水中全氟化合物

全氟化合物(PFCs)持久存在于水环境中,难以通过传统的水处理工艺去除,提高水中PFCs的去除性能具有重要意义。本研究采用快速小柱实验探究了UV、H₂O₂和颗粒活性炭(GAC)组合工艺对水中4种PFCs的去除效果,并探究了UV照射时长和H₂O₂质量浓度对PFCs的直接去除效果及其对后续GAC吸附的影响。结果表明：不同工艺条件下,长链全氟辛酸(PFOA)和全氟辛烷磺酸(PFOS)始终表现出较短链全氟丁酸(PFBA)和全氟丁烷磺酸(PFBS)更高的去除率。单独GAC吸附对长链全氟PFOA和PFOS去除率为59.6%和64.3%,但对短链PFBA和PFBS去除率仅为11.7%和13.1%。单独UV或单独H₂O₂分别与GAC联用时,随着UV照射时长和H₂O₂质量浓度的增加,4种PFCs的去除率略有增加,且UV照射的增益效果较H₂O₂更优。UV/H₂O₂/GAC联用工艺对水中4种PFCs的去除效果最佳,30 min UV/H₂O₂处理后经GAC吸附可去除90％以上的PFOA和PFOS,短链PFBA和PFBS去除率也达到50%以上。UV/H₂O₂/GAC联工艺的良好效果是由于UV/H₂O₂高级氧化过程产生的羟基自由基氧化反应降低了水中大分子有机物的含量,从而减弱了有机物对PFCs的竞争吸附作用。本研究可为水中PFCs的高效处理提供技术参考。     

UV/TiO2薄膜体系光降解酞酸酯研究

采用自制玻璃负载TiO2薄膜,研究了UV-V is/TiO2以及UV/TiO2/H2O2体系对2种酞酸酯DBP和DEHP的光催化降解情况。研究结果表明,TiO2在暗处对酞酸酯没有降解作用;UV/TiO2体系能有效光降解DBP和DEHP,TiO2具有明显的光催化作用,增强因子分别为fDBP=2.06,fDEHP=1.53;在一定浓度范围内DBP在UV/TiO2体系中的降解速率与其初始浓度成负一级动力学关系;UV/TiO2/H2O2体系对DBP的光降解能力远大于UV/TiO2和UV/H2O2体系,H2O2能显著提高TiO2的光催化活性。     

UV/H2O2工艺降解环丙沙星的研究

采用UV/₂O₂工艺去除水体中的喹诺酮类抗生素环丙沙星（CIP）。考察了溶液pH值、₂O₂投加量以及水体基质对环丙沙星降解效率的影响,分析了降解产物的生成情况。研究表明,环丙沙星的降解符合拟一级反应动力学模型。降解速率受溶液pH值的影响,酸性及中性条件,有利于环丙沙星的降解。₂O₂投加量的增大,使得降解速率逐渐增大,但速率增幅逐渐变缓;最佳₂O₂/环丙沙星摩尔比为2 000。实际水体中存在的NOM、NO^-₃,促进了单独UV作用下,环丙沙星的降解。水体中的?OH焠灭剂,抑制了UV/₂O₂联合作用下,环丙沙星的降解;实际水体中的光解速率常数低于超纯水中的光解速率常数。GC-MS分析表明,UV/₂O₂工艺,使环丙沙星氧化降解生成氨基乙酸、丙二酸、丙三醇和对苯二甲酸等小分子有机物。     

用Nano-TiO2/O3和Nano-TiO2/UV/O3去除腐殖酸并控制臭氧副产物的生成

采用Nano-TiO2/O3和Nano-TiO2/UV/O3进行小试实验。通过对DOC、UV254、BrO3-和甲醛进行检测分析,研究了不同体系去除腐殖酸（HA）并控制臭氧副产物生成的效果。结果表明,当HA浓度为10 mg·L-1时,Nano-TiO2/O3体系对DOC的去除主要在反应进行20 min内完成,去除率仅达12.0%左右,对UV254的去除主要发生在2 min内,去除率仅达14.5%左右;而Nano-TiO2/UV/O3体系DOC和UV254的去除率分别达32.8%和53.3%。HA的存在显著减少了Nano-TiO2/O3体系BrO3-的生成量,出水BrO3-浓度为29.00 μg·L-1,而Nano-TiO2/UV/O3体系出水BrO3-浓度为5.00 μg·L-1。研究表明,相比Nano-TiO2/O3体系,Nano-TiO2/UV/O3体系能更好地控制BrO3-生成,同时能提高对HA的去除效果,且无甲醛生成的风险。     

Role of cupric ions in the H2O2/UV oxidation of humic acids

The purpose of this study is to reveal the role of cupric ions as a natural water contaminant in the H2O2/UV oxidation of humic acids. Humic acids are naturally occurring organic matter and exhibit a strong tendency of complexation with some transition metal ions. Chlorination of humic acids causes potential health hazards due to formation of trihalomethane (THM). The removal of THM precursors has become an issue of public concern. The H2O2/UV process is capable of mineralizing humic acids due to formation of a strong oxidant, hydroxyl radicals, in reaction solution. Experiments were conducted in a re-circulated photoreactor. Different cupric concentrations (0-3.8 mg/l) and different pH values (4-9) were controlled to determine their effects on the degradation of humic acids, UV light absorbance at 254 nm, and H2O2. The presence of cupric ions inhibits humic mineralization and decreases the rate of destruction of humic acids which absorb UV light at 254 nm. On the other hand, the higher the cupric concentration, the lower the H2O2 decomposition rate. In the studied pH range, the minimum of total organic carbon (TOC) removal occurs at pH = 6 in the presence of 2.6 mg/l of cupric ions; both acidification (pH = 4) and alkaline condition (pH = 9) lead to a better removal of TOC. It is inferred from this study that the cupric-complexed form of humic acids is more refractory than the non-complexed one.     

UV/H2O2/Fe-FeOxH2x-3和UV/H2O2工艺降解水中富里酸的研究

采用硼氢化钠还原法制备核-壳结构的Fe-FeO_xH_2x-3复合材料，研究了富里酸在UV/H₂O₂和UV/H₂O₂/Fe-FeO_xH_2x-3两种不同反应体系下的降解情况。结果表明，核-壳结构Fe-FeO_xH_2x-3的存在，提高了UV/H₂O₂降解富里酸的反应速率，TOC去除达到84%。采用XAD树脂吸附法对反应前后的富里酸进行化学分级表征，结果表明，富里酸经反应后憎水酸（HoA）、弱憎水酸（WHoA）和憎水中性物质（HoN）都有所减少，进而转化为亲水性物质（HiM）；用超滤膜法对富里酸进行物理分级表征，考察了富里酸在反应前后分子量分布的变化情况。同时，富里酸经过反应后生成的中间产物降低了三氯甲烷生成趋势。     

Decomposition of 2-nitrophenol in aqueous solution by ozone and UV/ozone processes.

The decomposition of 2-nitrophenol in aqueous solutions by ozone and UV/ozone processes was found to be technically feasible under adequate experimental conditions. Formation of nitrate ions was observed following the decomposition of 2-nitrophenol by ozone and UV/ ozone processes. Increasing ozone dosage and UV light intensity accelerated the decomposition rate of 2-nitrophenol in an aqueous solution. The species distribution of 2-nitrophenol under various solution conditions plays a significant role in determining decomposition behavior. In most experiments conducted in this study, the decomposition of 2-nitrophenol by ozone and UV/ozone processes was favored to occur in alkaline conditions. The addition of 2-butanol accelerated the rate of gaseous ozone transfer to an aqueous phase by reducing the surface tension of aqueous solution and therefore enhancing the decomposition rate of 2-nitrophenol by ozone and UV/ozone processes.     

Oxidation of MCPA and 2,4-D by UV radiation, ozone, and the combinations UV/H2O2 and O3/H2O2

The phenoxyalkyl acid derivative herbicides MCPA (4-chloro 2-methylphenoxyacetic acid) and 2,4-D (2,4-dichlorophenoxyacetic acid) were oxidized in ultrapure water by means of a monochromatic UV irradiation and by ozone, as well as by the combinations UV/H2O2 and O3/H2O2. In the direct photolysis of MCPA, the quantum yield at 20 degrees C was directly evaluated and a value of 0.150 mol Eins(-1) was obtained in the pH range 5-9, while a lower value of 0.41 x 10(-2) mol Eins(-1) was determined at pH=3. Similarly, for 2,4-D a value of 0.81 x 10(-2) mol Eins(-1) was deduced, independent of the pH of work. The influence of the additional presence of hydrogen peroxide was established in the combined process UV/H2O2, and the specific contribution of the radical pathway to the global photo-degradation was evaluated. The oxidation by ozone and by the combination O3/H2O2 was also studied, with the determination of the rate constants for the reactions of both herbicides with ozone and hydroxyl radicals at 20 degrees C. These rate constants for the direct reactions with ozone were 47.7 and 21.9 M(-1) s(-1) for MCPA and 2,4-D respectively, while the found values for the rate constants corresponding to the radical reactions were 6.6 x 10(9) and 5.1 x 10(9) M(-1) s(-1).     

UV/H2O2协同光降解处理酒石酸镍废水

含镍电镀废水中酒石酸的存在,使得废水中总镍无法通过化学沉淀法去除,无法满足达标排放要求。采用UV/H2O2光降解法处理酒石酸镍体系废水,考察了不同反应pH值、过氧化氢投加量、光照时间对酒石酸镍体系络合废水的处理效果。实验结果表明：UV/H2O2法对酒石酸镍体系废水有很好的协同处理效果,光降解过程呈拟一级动力学过程;优化的酒石酸镍废水处理工艺为反应pH值3.0,30%过氧化氢投加量2 mL·L-1,15 W功率紫外灯光照下反应120 min,在优化的工艺条件下,采用化学沉淀法去除水中镍,处理后电镀废水中总镍可满足《电镀污染物排放标准》（GB 21900-2008）中0.5 mg·L-1要求。     

O3、H2O2／O3及UV／O3在焦化废水深度处理中的应用

采用O3、H2O2／O3及UV／O3等高级氧化技术（AOPs）对某焦化公司的生化出水进行深度处理,考察了O3与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响,确定出O3氧化反应的最佳工艺参数为：接触时间40min,溶液pH8．5,反应温度25℃,此条件下废水COD及UV254的去除率最高可达47．14％和73．47％;H2O2／O3及UV／O3两种组合工艺对焦化废水COD及UV254的去除率均有一定程度的提高,但H2O2／O3系统的运行效果取决于H2O2的投加量。研究结论表明,单纯采用COD作为评价指标,并不能准确反映出O3系列AOPs对焦化废水中有机污染物的降解作用。     

臭氧光催化降解地下水中天然有机物的研究

在现场开展了中试规模的臭氧光催化降解天然有机物的研究.研究表明,对大分子天然有机物占很大比例且重碳酸盐含量较高的地下水,臭氧投加量10 mg/L和反应时间10 min条件下,TOC的去除率不到20%,但UV254和三卤甲烷生成潜力(THMFP)去除率分别达到近60%和33.5%.臭氧光催化与活性炭吸附相连,能显著提高UV254的THMFP的去除率,但TOC去除率并不明显高于单独活性炭吸附.臭氧光催化使大分子有机物转化为小分子有机物,后者在活性炭上的吸附性提高且生化性改善,可望在生物活性炭上更有效地去除.