Innovative micro hole machining with minimum burr formation by the use of newly developed micro compound tool

The study focuses on the efforts for minimization of burr formation and improvement of hole surface roughness in micro through-hole machining. It deals with the development of micro compound tool which is consisting of a micro flat drill as the drilling part and a micro diamond-electroplated-grinding part for hole finishing. The finishing diameters of each drilling and grinding parts of the fabricated micro compound tool are 90 μm and 100 μm, respectively. The study focuses mainly on the effect of drill point angle and ultrasonic vibration applied during micro hole machining to the hole entrance and exit burrs formation. The used workpiece is made of stainless steel (SUS304) with a thickness of 100 μm. From the experiment, it was found that the tool having drill point angle of 118° resulted in a smaller burr formation although hole machining was conducted for 600 holes. Furthermore, the application of ultrasonic vibration during hole machining could improve the performance of the developed micro compound tool and decreased the burr size, especially the exit burr.     

The effect of spindle speed,feed-rate and machining time to the surface roughness and burr formation of Aluminum Alloy 1100 in micro-milling operation

This paper describes the characteristics and the cutting parameters performance of spindle speeds (n, rpm) and feed-rates (f, mm/s) during three interval ranges of machining times (t, minutes) with respect to the surface roughness and burr formation, by using a miniaturized micro-milling machine. Flat end-mill tools that have two-flutes, made of solid carbide with Mega-T coated, with 0.2 mm in diameter were used to cut Aluminum Alloy AA1100. The causal relationship among spindle speeds, feed-rates, and machining times toward the surface roughness was analyzed using a statistical method ANOVA. It is found that the feed-rate (f) and machining time (t) contribute significantly to the surface roughness. Lower feed-rate would produce better surface roughness. However, when machining time is transformed into total cut length, it is known that a higher feed-rate, that consequently giving more productive machining since produce more cut length, would not degrade surface quality and tool life significantly. Burr occurrence on machined work pieces was analyzed using SEM. The average sizes of top burr for each cutting parameter selection were analyzed to find the relation between the cutting parameters and burr formation. In this research, bottom burr was found. It is formed in a longer machining time compare the formation of top burr, entrance burr and exit burr. Burr formation is significantly affected by the tool condition, which is degrading during the machining process. This knowledge of appropriate cutting parameter selection and actual tool condition would be an important consideration when planning a micro-milling process to produce a product with minimum burr.     

Analysis of machined surface quality in a single-pass of ball-end milling on Inconel 718

The ball-end milling process is widely used for generating three-dimensional sculptured surfaces with definite curvature. In such cases, variation of surface properties along the machined surface curvatures is not well understood. Therefore, this paper reports the effect of machining parameters on the quality of surface obtained in a single-pass of a ball-end milling cutter with varying chip cross-sectional area. This situation is analogous to generation of free form cavities, pockets, and round fillets on mould surfaces. The machined surfaces show formation of distinct bands as a function of instantaneous machining parameters along the periphery of cutting tool edge, chip compression and instantaneous shear angle. A distinct variation is also observed in the measured values of surface roughness and micro-hardness in these regions. The maximum surface roughness is observed near the tool tip region on the machined surface. The minimum surface roughness is obtained in the stable cutting zone and it increases towards the periphery of the cutter. Similar segmentation was observed on the deformed chips, which could be correlated with the width of bands on the machined surfaces. The sub-surface quality analysis in terms of micro-hardness helped define machining affected zone (MAZ). The parametric effects on the machining induced shear and residual stresses have also been evaluated.     

Effect of process parameters on the performance of EDM process with ultrasonic assisted cryogenically cooled electrode

In this work the parametric study on EDM process using ultrasonic assisted cryogenically cooled copper electrode (UACEDM) during machining of M2 grade high speed steel has been performed. Electrode wear ratio (EWR), material removal rate (MRR) and surface roughness (SR) was the three parameters observed. Discharge current, pulse on time, duty cycle and gap voltage were the controllable process variables. The effect of process variables on EWR, MRR and SR has been analyzed. The MRR, EWR and SR obtained in EDM process with normal electrode, cryogenically cooled electrode and ultrasonic assisted cryogenically cooled electrode have been compared. EWR and SR were found to be lower in UACEDM process as compared to conventional EDM for the same set of process parameters, while MRR was at par with conventional EDM process. The surface integrity of work piece machined by UACEDM process has been found to be better as compared to conventional EDM process. The shape of the electrode has also been measured and it was found that the shape retention was better in UACEDM process as compared to conventional EDM process. Thus in the present work UACEDM process has been established to be better than conventional EDM process due to better tool life, tool shape retention ability and better surface integrity.     

Machining assessment of nano-crystalline hydroxyapatite bio-ceramic

Hydroxyapatite (HAP) is a widely used bio-ceramic in the fields of orthopedics and dentistry. This study investigates the machinability of nano-crystalline HAP (nHAP) bio-ceramic in end milling operations, using uncoated carbide tool under dry cutting conditions. Efforts are focused on the effects of various machining conditions on surface integrity. A first order surface roughness model for the end milling of nHAP was developed using response surface methodology (RSM), relating surface roughness to the cutting parameters: cutting speed, feed, and depth of cut. Model analysis showed that all three cutting parameters have significant effect on surface roughness. However, the current model has limited statistical predictive power and a higher order model is desired. Furthermore, tool wear and chip morphology was studied. Machined surface analysis showed that the surface integrity was good, and material removal was caused by brittle fracture without plastic flow.     

Orthogonal machining of single-crystal and coarse-grained aluminum

Orthogonal machining of single-crystal and coarse-grained (i.e., grain size considerably larger than the uncut chip thickness) materials has been a subject to many studies in the literature. The first part of this paper presents background on machining single-crystal materials, including experimental and modeling attempts. The second part briefly describes more recent modeling results from the authors, and presents new experimental results on planing and plunge-turning of single-crystal and coarse-grained aluminum using diamond tools. The experiments indicate that (1) cutting across grains of a coarse-grained aluminum workpiece produces distinctly varying forces and surface roughness from one grain to another, (2) plunge-turning and planing of single crystal aluminum provide equivalent force data for large rake angles, (3) forces alter between two distinct levels while cutting single crystals with small rake angles, and (4) with small rake angles, subsurface damage on single-crystal aluminum is extensive, reaching depths comparable to the uncut chip thickness.     

An experimental investigation into micro ball end-milling of silicon

Silicon is a representative operational material for semiconductor and micro-electronics. In certain MEMS applications, it is required to fabricate three dimensional channels and complex pattern on silicon substrate. Such features are typically fabricated by photolithography and chemical etching. These processes have low productivity and have certain other limitations. Therefore, a viable switch-over from non-traditional fabrication processes to traditional machining is highly desired for improved productivity in high-mix low-volume production. However, machining of silicon by traditional process is extremely difficult due to its high brittleness. Even very small forces produced during machining can cause brittle fracture on silicon surface resulting in deteriorated surface quality. The fundamental principle in machining of a brittle material such as silicon is to achieve material removal through plastic deformation rather than crack propagation. This paper presents the experimental results of ductile-mode machining of silicon by micro ball end-milling. The workpiece surface was inclined to the rotational axes of the cutter to improve the surface finish. It was established experimentally that 15-μm deep, fracture-free slots can be machined on silicon wafer by micro ball end-milling if the feed rate is below a certain threshold. The influence of several machining parameters on the roughness of machined-surface was also investigated. Cubic boron nitride (CBN) is presented as much economical alternative tool-material to single-crystal diamond for machining silicon in ductile-mode.     

Study of ultrasonic assisted cryogenically cooled EDM process using sintered (Cu–TiC) tooltip

In most EDM operations, the maximum contribution in the total operation cost is the tool cost. Electrode wear is a major problem in EDM process. Therefore, in this paper, the process performance of sintered copper (Cu)–titanium carbide (TiC) electrode tip in ultrasonic assisted cryogenically cooled electrical discharge machining (UACEDM) has been studied. The performance parameters studied in this paper are electrode wear ratio (EWR), material removal rate (MRR), surface roughness (SR), out of roundness and surface integrity. The process parameters considered in this study are discharge current, pulse on time, duty cycle and gap voltage. Cermet was fabricated, having copper content of 75% and titanium carbide content of 25%, by mixing, pressing, and sintering. The performance of the newly formed cermet electrode tip is compared with conventional copper electrode tip for UACEDM process and analyzed. It has been observed that EWR and out of roundness decreases when cermet electrode tip is used as compared to conventional tooltip. It has also been observed that MRR and SR increase when cermet tooltip is used. The surface cracks density and crack width on workpiece machined by cermet tooltip have been found to be lesser as compared to the specimen machined by conventional tooltip.     

Cryogenic Machining of Tantalum

A new approach for the machining of tantalum is presented. The new approach is a combination of traditional turning and cryogenically enhanced machining (CEM). In the tests, CEM was used to reduce the temperature at the cutting tool/workpiece interface, and thus reduce the temperature-dependent tool wear to prolong cutting tool life. The new method resulted in a reduction of surface roughness of the tantalum workpiece by 200% and a decrease of cutting forces by approximately 60% in experiments. Moreover, cutting tool life was extended up to 300% over that in the conventional machining.     

Evaluation of vegetable based cutting fluids with extreme pressure and cutting parameters in turning of AISI 304L by Taguchi method

Many problems such as health and environment issues are identified with the use of cutting fluids (CFs). There has been a high demand for developing new environmentally friendly CFs such as vegetable based cutting fluids (VBCFs) to reduce these harmful effects. In this study, performances of six CFs, four different VBCFs from sunflower and canola oils with different ratios of extreme pressure (EP) additives, and two commercial types of CFs (semi-synthetic and mineral) are evaluated for reducing of surface roughness, and cutting and feed forces during turning of AISI 304L austenitic stainless steel with carbide insert tool. Taguchi’s mixed level parameter design (L₁₈) is used for the experimental design. Cutting fluid, spindle speed, feed rate and depth of cut are considered as machining parameters. Regression analyses are applied to predict surface roughness, and cutting and feed forces. ANOVA is used to determine effects of the machining parameters and CFs on surface roughness, cutting and feed forces. In turning of AISI 304L, effects of feed rate and depth of cut are found to be more effective than CFs and spindle speed on reducing forces and improving the surface finish. Performances of VBCFs and commercial CFs are also compared and results generally show that sunflower and canola based CFs perform better than the others.     

Effects of magnetic field and rotary tool on EDM performance

In this work, the effects of tool rotation and various intensities of external magnetic field on electrical discharge machining (EDM) performance have been studied. Experimental trials divided into three regimes of low energy regime, middle energy regime and high energy regime. The influences of process parameters were investigated on main outputs of material removal rate (MRR) and surface roughness (SR). In order to correlate the input parameters and output values two mathematical models were developed to predict the MRR and SR according to variations of discharge energy, magnetic field intensity and tool rotational speed. Results indicated that the applying a rotational magnetic field around the machining gap improves the MRR and SR. Combination of rotational magnetic field and rotary electrode increases the machining performance, in comparison of previous conditions. This is due to better flushing debris from machining gap. This work introduces a new method for improving the machining performance, in cost and time points of view.     

Experimental Evaluation of Cutter Orientation When Ball Nose End Milling Inconel 718™

High-speed machining (HSM), specifically end milling and ball end cutting, is attracting interest in the aerospace industry for the machining of complex 3D aerofoil surfaces in titanium alloys and nickel-based superalloys. Following a brief introduction on HSM and related aerospace work, the paper reviews published data on the effect of cutter/workpiece orientation, also known as engagement or tilt angle, on tool performance. Such angles are defined as ±β_fN and ±β_f.Experimental work is detailed on the effect of cutter orientation on tool life, cutting forces, chip formation, specific force, and workpiece surface roughness when high-speed ball end milling Inconel 718™. Dry cutting was performed using 8 mm diameter PVD-coated solid carbide cutters with the workpiece mounted at an angle of 45° from the cutter axis.A horizontal downward (-β_fN) cutting orientation provided the best tool life with cut lengths ∼50% longer than for all other directions (+β_fN, +β_f, and –β_f). Evaluation of cutting forces and associated spectrum analysis of results indicated that cutters employed in a horizontal downward direction produced the least vibration. This contributed to improved workpiece surface roughness, with typical mean values of ∼0.4 μm Ra as opposed to ∼1.25 μm Ra when machining in the vertical downward (–β_f) direction.     

Performance-Based Predictive Models and Optimization Methods for Turning Operations and Applications: Part 3—Optimum Cutting Conditions and Selection of Cutting Tools

This paper presents a summary of recent developments in developing performance-based machining optimization methodologies for turning operations. Four major machining performance measures (cutting force, tool wear/tool life, chip form/chip breakability, and surface roughness) are considered in the present work, which involves the development and integration of hybrid models for single and multi-pass turning operations with and without the effects of progressive tool wear. Nonlinear programming techniques were used for single-pass operations, while a genetic algorithms approach was adopted for multi-pass operations. This methodology offers the selection of optimum cutting conditions and cutting tools for turning with complex grooved tools.     

Investigating surface roughness,material removal rate and corrosion resistance in PMEDM of γ-TiAl intermetallic

Titanium aluminide intermetallics offer an attractive combination of low density and good oxidation, corrosion and ignition resistance with unique mechanical properties. In this study two series of machining tests are designed. Firstly the powder mixed electrical discharge machining (PMEDM) of γ-TiAl by means of different powders such as aluminum, chrome, silicon carbide, graphite and iron is performed to investigate the output characteristics of surface roughness and topography, material removal rate (MRR), electrochemical corrosion resistance of machined samples and also the machined surfaces are investigated by means of EDS and XRD analyses. Secondly after selection the aluminum powder as the most appropriate kind of powder, the current, pulse on time, powder size and powder concentration are changed in different levels for overall comparison between EDM and PMEDM output characteristics. In the first setting of input machining parameters, aluminum powder improves the surface roughness of TiAl sample about 32% comparing with EDM case and also aluminum particles with the size of 2 μm, in the second setting of input parameters lead to 54% enhancement of MRR comparing with EDM case. The electrochemical corrosion results show that, corrosion resistance of the samples which are machined by graphite and chrome powders respectively are about three and two times more than the sample which is machined without powder.     

铣削工艺参数对锡铋合金表面粗糙度特征影响及试验分析

目的对锡铋合金表面粗糙度特征进行研究分析,提高表面加工质量。方法采用正交试验设计方法,以最小表面粗糙度作为优化指标,以主轴转速、铣削深度、进给速度、铣削宽度作为影响因素,进行精密铣削试验研究。结果利用方差分析确定了进给速度是锡铋合金铣削表面粗糙度最重要的影响因素,并基于田口方法优化分析得到了锡铋合金铣削加工工艺最优组合。结论采用田口法对锡铋合金铣削工艺参数优化,有效地减少了加工表面粗糙度,提高了工件表面质量。     

大面积镜面电火花加工的实验研究

介绍了大面积镜面电火花加工法现状.通过改变混粉工作液中微粉的种类、浓度、加工参数以及加工面积进行了工艺试验.验证了混粉电火花加工的确能改善表面粗糙度.     

Experimental investigation of turning AISI 1045 steel using cryogenic carbon dioxide as the cutting fluid

The intensive temperatures in high speed machining not only limit the tool life but also impair the machined surface by inducing tensile residual stresses, microcracks and thermal damage. This problem can be handled largely by reducing the cutting temperature. When the conventional coolant is applied to the cutting zone, it fails to remove the extent of the heat effectively. Hence, a cryogenic coolant is highly recommended for this purpose. In this paper, an attempt has been made to use cryogenic carbon dioxide (CO₂) as the cutting fluid. Experimental investigations are carried out by turning AISI 1045 steel in which the efficiency of cryogenic CO₂ is compared to that of dry and wet machining with respect to cutting temperature, cutting forces, chip disposal and surface roughness. The experimental results show that the application of cryogenic CO₂ as the cutting fluid is an efficient coolant for the turning operation as it reduced the cutting temperature by 5%–22% when compared with conventional machining.It is also observed that the surface finish is improved to an appreciable amount in the finished work piece on the application of cryogenic CO₂. The surface finish is improved by 5%–25% in the cryogenic condition compared with wet machining.     

Laser tempering based turning process for efficient machining of hardened AISI 52100 steel

Cost-effective machining of hardened steel components such as a large wind turbine bearing has traditionally posed a significant challenge. This paper presents an approach to machine hardened steel parts efficiently at higher material removal rates and lower tooling cost. The approach involves a two-step process consisting of laser tempering of the hardened workpiece surface followed by conventional machining at higher material removal rates with lower cost ceramic tools to efficiently remove the tempered material. The laser scanning parameters that yield the highest depth of tempered layer are obtained from a kinetic phase change model. Machining experiments are performed to demonstrate the possibility of higher material removal rates and improved tool wear behavior compared to the conventional hard turning process. Tool wear performance, cutting forces, and surface finish of Cubic Boron Nitride (CBN) tools as well as low cost ceramic tools are compared in machining of hardened AISI 52100 steel (~63 HRC). In addition, cutting forces and surface finish are compared for the laser tempering based turning and conventional hard turning processes. Experimental results show the potential benefits of the laser tempering based turning process over the conventional hard turning process.     

Pulsed laser micro polishing: Surface prediction model

The objective of this work is to predict the final roughness of metal surfaces that have undergone pulsed laser micro polishing. The motivation for pulsed laser micro polishing is to reduce the surface roughness of parts whose surface texture can approach the feature size. Being able to predict the magnitude of the polishing and frequency (wavelength) content of the surface will assist in the design of optimal processing parameters with minimal experiments. Laser pulses are used to create shallow melt pools with a controlled size (e.g., depth) and duration in order to allow surface tension forces to “pull down” asperities with small radius of curvature. There is no ablation occurring in the process being modeled. The melt depth and duration are predicted with a transient, two-dimensional axisymmetric heat transfer model with temperature-dependent material properties. The surface of the melt pool is analytically modeled as oscillations of stationary capillary waves with damping resulting from the forces of surface tension and viscosity. Above a critical spatial frequency, f_cr, a significant reduction in the amplitude of the spatial Fourier components is expected. The work described in this paper extends the concept of critical frequency to a physics-based prediction methodology for predicting the spatial frequency content and surface roughness after polishing, given the features of the original surface, the material properties, and laser parameters. The proposed prediction methodology was validated using line polishing data for stainless steel 316L and area polishing results for pure nickel, Ti6Al4V, and Al-6061-T6. The predicted average surface roughnesses were within 12% of the values measured on the polished surfaces.     

Effect of fluid concentration in titanium machining with an atomization-based cutting fluid (ACF) spray system

The aim of this work is to investigate the effect of metal-working fluid (MWF) concentration on the machining responses including tool life and wear, cutting force, friction coefficient, chip morphology, and surface roughness during the machining of titanium with the use of the ACF spray system. Five different concentrations from 5 to 15% of a water-soluble metalworking fluid (MWF) were applied during turning of a titanium alloy, Ti–6Al–4V. The thermo-physical properties such as viscosity, surface tension and thermal conductivity of these concentrations were also measured. The test results demonstrate that the tool life first extends with the increase in MWF concentration and then drops with further increase. At low concentration (e.g., 5%), a lack of the lubrication effect causes to increase in a higher friction at the tool–chip interface resulting in severe chipping and tool nose/flank wear within a short machining time. On the other hand, at high concentration, the cooling effect is less. This increases cutting temperature and a faster thermal softening/chipping/notching of the tool material and higher friction at the tool–chip–workpiece interaction zones resulting in early tool failure. A good balance between the cooling and the lubrication effects seems to be found at the 10% MWF concentration as it offers the best machining performance. However, machining with flood coolant is observed to perform the best in the range of 5–7%.