混合胺MEA＋DETA吸收CO2的影响因素

以MEA为主体,DETA为添加剂,考察1h内,在温度298～338K,压力300～700kPa,混合胺溶液初始浓度（质量分数）4％～20％范围内,MEA＋DETA不同配比的混合吸收剂吸收CO2的特性。获得MEA＋DETA混合胺吸收CO2的最佳吸收条件为：308K、500kPa、总胺质量浓度为20％,MEA与DETA的配比为8：2。     

超临界CO2回收线路板工艺研究

采用正交试验设计进行了超临界CO₂回收废弃印刷线路板的实验。以温度、压强、时间和夹带剂为实验因素,通过对实验前后样本在重量、厚度、弯曲强度和断裂强度四方面变化的分析考察了各实验因素对实验效果的影响。实验结果表明,影响超临界CO₂法回收印刷线路板的最主要因素为温度、时间和夹带剂,超临界CO₂法回收废弃印刷线路板的最佳工艺条件：温度270℃,压强大于7.38 MPa,时间3 h,夹带剂(水)160 mL。实验进一步验证了压强对实验结果的非显著性影响。     

O3、H2O2/O3及UV/O3在焦化废水深度处理中的应用

采用O₃、H₂O₂/O₃和UV/O₃等高级氧化技术(AOPs)对某焦化公司的生化出水进行深度处理,考察了O₃与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响,确定出O₃氧化反应的最佳工艺参数为：接触时间40 min,溶液pH 8.5,反应温度25℃,此条件下废水COD及UV₂₅₄的去除率最高可达47.14%和73.47%;H₂O₂/O₃及UV/O₃两种组合工艺对焦化废水COD及UV₂₅₄的去除率均有一定程度的提高,但H₂O₂/O₃系统的运行效果取决于H₂O₂的投加量。研究结论表明,单纯采用COD作为评价指标,并不能准确反映出O₃系列AOPs对焦化废水中有机污染物的降解作用。     

用H2O2/Fe3+处理高浓度含甲醛废水的研究

研究采用H₂O₂/Fe³⁺催化氧化处理高浓度含甲醛废水,探讨了双氧水和催化剂投加量、反应pH及反应温度等操作条件对处理效果的影响,并通过酸溶解回用失活催化剂。结果表明,较优的操作条件为：H₂O₂/COD（质量比）=2.2～2.6,Fe³⁺/H₂O₂（摩尔比）=0.048～0.058,反应pH 1.80～2.68,反应温度50℃,反应时间40 min;在上述操作条件下,甲醛去除率达到99%以上,COD去除率达到85%以上。失活的催化剂可通过稀酸溶解后循环使用,其效果与三价铁盐作催化剂的基本相同。采用H₂O₂/Fe³⁺处理含甲醛废水具有比采用H₂O₂/Fe³⁺较优的效果。     

La2O3/ZnO/TiO2光催化降解活性艳红K-2BP的研究

采用溶胶-凝胶法制备了La₂O₃/ZnO/TiO₂复合光催化剂,以紫外灯为光源,活性艳红K-2BP为模型降解物,研究了La₂O₃/ZnO/TiO₂的光催化性能。结果表明：当锌和镧的掺杂量w(ZnO)=20%, w(La₂O₃)=0.5%, 煅烧温度为500℃时,La₂O₃/ZnO/TiO₂复合光催化剂的光催化活性最高;当催化剂投加量4 g/L,通气量800 mL/min,初始pH值3.12时,La₂O₃/ZnO/TiO₂对活性艳红K-2BP的降解效果最好。实验证明,La₂O₃/ZnO/TiO₂对活性艳红K-2BP的降解遵从Langmuir-Hinshelwood动力学模型,测得其反应速率常数k＝11.5 mg/(L·min);吸附常数K＝2.88×10^-2 L/mg。     

UV/H2O2工艺降解环丙沙星的研究

采用UV/₂O₂工艺去除水体中的喹诺酮类抗生素环丙沙星（CIP）。考察了溶液pH值、₂O₂投加量以及水体基质对环丙沙星降解效率的影响,分析了降解产物的生成情况。研究表明,环丙沙星的降解符合拟一级反应动力学模型。降解速率受溶液pH值的影响,酸性及中性条件,有利于环丙沙星的降解。₂O₂投加量的增大,使得降解速率逐渐增大,但速率增幅逐渐变缓;最佳₂O₂/环丙沙星摩尔比为2 000。实际水体中存在的NOM、NO^-₃,促进了单独UV作用下,环丙沙星的降解。水体中的?OH焠灭剂,抑制了UV/₂O₂联合作用下,环丙沙星的降解;实际水体中的光解速率常数低于超纯水中的光解速率常数。GC-MS分析表明,UV/₂O₂工艺,使环丙沙星氧化降解生成氨基乙酸、丙二酸、丙三醇和对苯二甲酸等小分子有机物。     

负载V2O5-WO3/TiO2掺炭纤维脱除烟气中Hg0

通过固定床实验系统研究烟气脱除零价汞的实验,首先研究了滤袋常用的聚苯硫醚（polyphenylene sulfide,PPS）以及活性炭纤维（activated carbon fiber,ACF）在不同温度、不同气体组分下负载V₂O₅-WO₃/TiO₂催化剂,对模拟燃煤烟气中零价汞（Hg⁰）的脱除效果。然后对比研究了活性炭纤维协同滤袋常用纤维负载催化剂后,对模拟燃煤烟气中Hg⁰的脱除性能。结果表明,在汞蒸气入口浓度为50 μg/m³,纯N₂气氛下,当温度为25℃时,两者脱除率均能达到99%,当温度为200℃,负载催化剂的活性炭纤维脱除率在30%左右,PPS纤维仅为10%左右。在200℃情况下,模拟烟气的组分为N₂+O₂时,2种纤维的Hg⁰脱除率提高了10%~20%,当在混合气体中添加0.01‰后,负载催化剂的PPS纤维Hg⁰脱除率能达到80%,活性炭纤维Hg⁰脱除率能达到98%。当温度为200℃,模拟烟气的组分为N₂+O₂+HCl时,不同性能掺炭纤维负载催化剂后Hg⁰脱除率在69%~95%范围之间变化,其中PPS掺炭纤维对Hg⁰脱除效率最高达到95%,因此,负载V₂O₅-WO₃/TiO₂催化剂的PPS掺炭纤维能在高温烟气中保持较高的Hg⁰脱除率。     

CuMnOx/γ-Al2O3及稀土助剂对VOCs催化燃烧性能的影响

利用浸渍法制备了Cu-Mn复合氧化物催化剂和加入不同稀土含量的Cu-Mn复合氧化物催化剂,通过实验优选出加入稀土催化剂中稀土含量的最优配比,以气相色谱为检测手段,考察了加入稀土和不加稀土催化剂的催化燃烧性能,结果表明,加入稀土的催化剂T₉₉（催化处理效率达到99%时的温度）比不加稀土的催化剂降低30～40℃,具有更好的低温活性,且对多种VOCs均能降低反应温度。     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La₂O₃(0.5%)-ZnO(20%)-TiO₂/沸石复合光催化剂,以20 W紫外灯为光源,在自制的光催化反应器中降解活性艳红K-2BP,考察了光照时间、空气通入量、催化剂用量、溶液初始浓度、H₂O₂与Fe³⁺投加量等对活性艳红K-2BP光催化降解率的影响。结果表明,当溶液初始浓度为60 mg/L,催化剂投加量为12 g/L,通气量为1 200 mL/min,光照2.5 h,活性艳红K-2BP的降解率可达99.2%;H₂O₂和Fe³⁺投加量为4 mL/L和3 g/L时,光照1 h活性艳红K-2BP降解率分别为100%和97.2%。紫外可见吸收光谱显示,LZTZ光催化剂可有效降解印染废水。     

vis／H2O2／草酸铁处理活性艳红染料的实验研究

采用vis／H₂O₂／草酸铁法，对活性艳红染料废水进行处理。研究了H₂O₂、K₂C₂O₄和Fe₂(SO₄)₃·7H₂O的投加量、pH值和光照时间等因素对染料废水处理效果的影响和最佳处理条件。结果表明，pH值2.5；30%H₂O₂的投加量0.1 mL；0.1 mol/L Fe₂(SO₄)₃·7H₂O的投加量1.0 mL；0.1 mol/L K₂C₂O₄的投加量1.5 mL；光照时间40 min的最佳条件下，70 mg/L的活性艳红模拟染料废水脱色率可达99.82%。通过对vis／H₂O₂／草酸铁法和Fenton法、H₂O₂法、草酸铁法等方法进行对比实验，vis／H₂O₂／草酸铁法明显优于其他方法，是一项有研究价值和开发应用前景的污染治理新技术。     

纯二氧化碳条件下小球藻固定CO2

微藻固碳已经成为消减温室气体排放的新的研究热点。利用静态吸收方法,考查了通人纯CO2对普通小球藻生长特点、固定CO2效率以及藻液pH值变异的影响。结果表明：通入纯CO2使小球藻生长延滞期显著延长,比普通培养延长10～12d,对其他生长阶段的影响不大;小球藻固定CO2速率可分为2个过程,即物理固碳过程和生物固碳过程,前者在藻细胞延滞期发生,峰值由CO。溶解于培养液造成,后者在藻细胞生长的指数期、稳定期和衰退期发生,峰值由藻细胞指数生长造成,2个过程中,固定CO2速率的变化趋势都是先增大后降低;纯CO2条件下,藻液pH值变化速率高,4d内,藻液即被酸化,随后藻液pH值变化速率逐渐降低,且pH值稳定在适宜水平。因此,采用小球藻固定高浓度CO2时,建议提高接种量并加强培养前期的pH值监测和调控,以保证藻液保持适宜的pH值,并缩短培养时间,提高生物固碳效率。     

Elevated CO2 response of photosynthesis depends on ozone concentration in aspen

The effect of elevated CO₂ and O₃ on apparent quantum yield (?), maximum photosynthesis (P_max), carboxylation efficiency (V_cmax) and electron transport capacity (J_max) at different canopy locations was studied in two aspen (Populus tremuloides) clones of contrasting O₃ tolerance. Local light climate at every leaf was characterized as fraction of above-canopy photosynthetic photon flux density (%PPFD). Elevated CO₂ alone did not affect ? or P_max, and increased J_max in the O₃-sensitive, but not in the O₃-tolerant clone. Elevated O₃ decreased leaf chlorophyll content and all photosynthetic parameters, particularly in the lower canopy, and the negative impact of O₃ increased through time. Significant interaction effect, whereby the negative impact of elevated O₃ was exaggerated by elevated CO₂ was seen in Chl, N and J_max, and occurred in both O₃-tolerant and O₃-sensitive clones. The clonal differences in the level of CO₂ × O₃ interaction suggest a relationship between photosynthetic acclimation and background O₃ concentration.     

The growth response of Alternanthera philoxeroides in a simulated post-combustion emission with ultrahigh [CO2] and acidic pollutants

Although post-combustion emissions from power plants are a major source of air pollution, they contain excess CO₂ that could be used to fertilize commercial greenhouses and stimulate plant growth. We addressed the combined effects of ultrahigh [CO₂] and acidic pollutants in flue gas on the growth of Alternanthera philoxeroides. When acidic pollutants were excluded, the biomass yield of A. philoxeroides saturated near 2000 μmol mol⁻¹ [CO₂] with doubled biomass accumulation relative to the ambient control. The growth enhancement was maintained at 5000 μmol mol⁻¹ [CO₂], but declined when [CO₂] rose above 1%, in association with a strong photosynthetic inhibition. Although acidic components (SO₂ and NO₂) significantly offset the CO₂ enhancement, the aboveground yield increased considerably when the concentration of pollutants was moderate (200 times dilution). Our results indicate that using excess CO₂ from the power plant emissions to optimize growth in commercial green house could be viable.     

Influence of the operation conditions on CO2 capture by CaO-derived sorbents prepared from synthetic CaCO3

In this work, a statistical experimental design is performed in order to prepare CaCO₃ materials for use as CaO-based CO₂ sorbent precursors. The influence of different operational parameters such as synthesis temperature (ST), stirring rate (SR) and surfactant percent (SP) on CO₂ capture is studied by applying Response Surface Methodology (RSM). The samples were characterized using different analytical techniques including X-ray diffraction, N₂ adsorption isotherm analysis and Scanning Electron Microscopy–X-ray Energy Dispersive Spectroscopy (SEM-EDX). CO₂ capture capacity was determined by means of a thermogravimetric analyzer which recorded the mass uptake of the samples when these were exposed to a gas stream containing diluted (15%) CO₂. The statistical approach used in this work provides a rapid way of predicting and optimizing the main preparation variables of CaO-derived sorbents for CO₂ sorption. The results obtained clearly indicate that four parameters statistically influence CO₂ uptake: SR, the square of SR, its interaction with SP and the square of SP.     

Gene expression responses of paper birch (Betula papyrifera) to elevated CO2 and O3 during leaf maturation and senescence

Gene expression responses of paper birch (Betula papyrifera) leaves to elevated concentrations of CO₂ and O₃ were studied with microarray analyses from three time points during the summer of 2004 at Aspen FACE. Microarray data were analyzed with clustering techniques, self-organizing maps, K-means clustering and Sammon's mappings, to detect similar gene expression patterns within sampling times and treatments. Most of the alterations in gene expression were caused by O₃, alone or in combination with CO₂. O₃ induced defensive reactions to oxidative stress and earlier leaf senescence, seen as decreased expression of photosynthesis- and carbon fixation-related genes, and increased expression of senescence-associated genes. The effects of elevated CO₂ reflected surplus of carbon that was directed to synthesis of secondary compounds. The combined CO₂ + O₃ treatment resulted in differential gene expression than with individual gas treatments or in changes similar to O₃ treatment, indicating that CO₂ cannot totally alleviate the harmful effects of O₃.     

O3/H2O2处理嘧啶废水的研究

采用O3/H2O2法对嘧啶废水进行处理,考察了不同反应条件对嘧啶和COD去除率的影响,并对O3/H2O2降解嘧啶的反应机制和动力学进行了初步探讨.实验结果表明,在pH值为11,反应时间为70 min,O3流量为4g/h,H2O2投加量为50 mmol/L的条件下,废水的嘧啶和COD的去除率分别达到86.46%和74.9...     

负载纳米TiO_2凹凸棒黏土的制备表征及对Mn~(2+)的吸附性能

以溶胶-凝胶法制备了负载纳米TiO2凹凸棒黏土吸附剂,采用SEM、XRD等分析方法对负载纳米TiO2凹凸棒黏土前后的结构进行了表征,并对Mn2+进行了吸附性能的研究。结果表明:经过高温焙烧后的负载纳米TiO2凹凸棒黏土吸附剂较负载前的凹凸棒黏土,因其结构中的结晶水和沸石水脱失,内部孔道面积和表面积增加,活性吸附位点的数量增大,吸附能力有了明显提高。在室温条件下(20~25℃),pH为5~6,吸附平衡时间为120 min时,负载纳米TiO2凹凸棒黏土吸附剂对Mn2+有较好的吸附效果。     

钛基IrO2-SnO2电极在烟气海水脱硫恢复系统中的应用

采用浸渍-热分解法制备了含IrOx-TiO2中间层的IrO2-SnO2电极,得到的电极具有较高的析氯电催化活性和较强的稳定性,并通过电化学氧化法对Na2SO3海水脱硫模拟液进行处理,考察了电流密度、温度、pH值和电解时间等电解工艺参数对Na2SO3去除率和化学需氧量COD的影响.结果表明,在电流密度为200 mA/cm...     

Diurnal changes in photosynthetic parameters of Populus tremuloides, modulated by elevated concentrations of CO2 and/or O3 and daily climatic variation

The diurnal changes in light-saturated photosynthesis (Pn) under elevated CO₂ and/or O₃ in relation to stomatal conductance (g_s), water potential, intercellular [CO₂], leaf temperature and vapour-pressure difference between leaf and air (VPD_L) were studied at the Aspen FACE site. Two aspen (Populus tremuloides Michx.) clones differing in their sensitivity to ozone were measured. The depression in Pn was found after 10:00 h. The midday decline in Pn corresponded with both decreased g_s and decreased Rubisco carboxylation efficiency, Vc_max. As a result of increasing VPD_L, g_s decreased. Elevated [CO₂] resulted in more pronounced midday decline in Pn compared to ambient concentrations. Moreover, this decline was more pronounced under combined treatment compared to elevated CO₂ treatment.The positive impact of CO₂ on Pn was relatively more pronounced in days with environmental stress but relatively less pronounced during midday depression. The negative impact of ozone tended to decrease in both cases.