110离子交换树脂担载催化齐净化低浓度PH3

以110丙烯酸系阳离子交换树脂作为载体,Pd（Ⅱ）-Cu（Ⅱ）为主催化剂,制成担载型过渡金属催化剂。以N2为载气,对反应温度、氧含量、催化剂用量3个因素进行催化氧化净化低浓度PH3研究。实验结果表明,在氧含量为3．7％,温度为72℃时,催化剂的催化活性较高;PH3净化效率随催化剂用量增大而提高。在优化后的实验条件下,考察催化剂以CO为载气时催化剂对PH3的净化效率,虽然净化效果比以N2为载气时差,但反应较稳定,持续时间较长,有较好的抗杂毒性,且催化剂具有再生性能。     

金属改性碳脱除PH3和H2S动力学及反应机理研究

为综合利用黄磷尾气中的CO,通过计算平均活化能和测定XPS、TG/DTA和氮吸附特性的方法,研究了Cu²⁺和某金属离子Mn⁺改性碳脱除PH₃和H₂S的动力学和反应机理问题。结果表明：H₂S在金属改性碳上反应时平均活化能为134.4 J/mol为-0.76级反应,PH₃在金属改性碳上反应时平均活化能为1 247.6 J/mol为-0.8级反应;减小改性碳粒径增加流量可以显著提高其脱除PH₃和H₂S的速率;XPS、TG/DTA和孔径分布分析证明,改性碳净化H₂S和PH₃是一个催化吸附过程,H₂S和PH₃首先与氧在改性碳表面进行催化氧化反应,然后生成S和P₂O₅沉积吸附在改性碳表面。     

负载V2O5-WO3/TiO2掺炭纤维脱除烟气中Hg0

通过固定床实验系统研究烟气脱除零价汞的实验,首先研究了滤袋常用的聚苯硫醚（polyphenylene sulfide,PPS）以及活性炭纤维（activated carbon fiber,ACF）在不同温度、不同气体组分下负载V₂O₅-WO₃/TiO₂催化剂,对模拟燃煤烟气中零价汞（Hg⁰）的脱除效果。然后对比研究了活性炭纤维协同滤袋常用纤维负载催化剂后,对模拟燃煤烟气中Hg⁰的脱除性能。结果表明,在汞蒸气入口浓度为50 μg/m³,纯N₂气氛下,当温度为25℃时,两者脱除率均能达到99%,当温度为200℃,负载催化剂的活性炭纤维脱除率在30%左右,PPS纤维仅为10%左右。在200℃情况下,模拟烟气的组分为N₂+O₂时,2种纤维的Hg⁰脱除率提高了10%~20%,当在混合气体中添加0.01‰后,负载催化剂的PPS纤维Hg⁰脱除率能达到80%,活性炭纤维Hg⁰脱除率能达到98%。当温度为200℃,模拟烟气的组分为N₂+O₂+HCl时,不同性能掺炭纤维负载催化剂后Hg⁰脱除率在69%~95%范围之间变化,其中PPS掺炭纤维对Hg⁰脱除效率最高达到95%,因此,负载V₂O₅-WO₃/TiO₂催化剂的PPS掺炭纤维能在高温烟气中保持较高的Hg⁰脱除率。     

改性活性炭吸附净化黄磷尾气中的PH3

通过钢瓶配气模拟和气相色谱GC-14C测定的方法，研究了改性活性炭吸附净化黄磷尾气中PH₃的相关问题。得到了吸附反应的最佳吸附温度、氧含量、气体流量、改性液浓度、活性炭粒径和焙烧温度。再生方法可行，可通过再生液回收磷酸。热重差热分析和孔径分布初步证明吸附质为磷和磷氧化物。     

尿素/三乙醇胺吸收烟气NOx的实验研究

以尿素作为吸收液,与NO_x反应生成N₂和CO₂,脱除烟气中的氮氧化物。以一套双级串连的填料塔为主体反应器,分别对气速、液气比、反应物浓度、添加剂浓度和反应温度等参数对尿素溶液吸收NO_x反应的影响进行了实验研究,获得了优化实验工况,研究结果显示,在气速为0.1 m/s、液气比为16 L/m³、三乙醇胺为0.01%(质量比)、尿素浓度为13%（质量比）工况下, 反应温度为30~70℃,脱硝总效率可达50％以上,且随着NO_x体积分数增加而提高。     

CuCoOx/TiO2催化氧化NO性能研究

采用浸渍法制备了CuCoOx/TiO₂催化剂,考察了焙烧温度、反应温度、氧含量、NO浓度和空间速度对催化剂催化氧化NO性能的影响,并考察了催化剂的抗硫抗水性能。XRD、TPR和BET分析表明,350℃焙烧的催化剂具有CuCo₂O₄尖晶石结构,比表面积大,对NO的氧化效果好。在空速为5 000 h^-1,NO进口浓度500 mg/m³,含氧量10%的条件下,反应温度300℃时NO转化率可达79.5%,250℃时NO转化率接近50%。该催化剂具有良好的单独抗SO₂、抗H₂O毒化性能,H₂O和SO₂同时存在时很快失活。该催化剂可用于不同时含H₂O和SO₂的含NO气体催化氧化后再吸收处理。     

光助Ce-Fe/Al2O3催化H2O2降解阳离子红GTL模拟废水

利用Ce-Fe/Al₂O₃为催化剂的非均相光Fenton体系降解阳离子红GTL模拟废水，考察了H₂O₂浓度、催化剂用量、初始pH值及不同工艺过程对降解效果的影响，通过紫外-可见漫反射光谱、红外光谱、XPS手段研究铁在反应中的价态变化。结果表明，在11 W低压汞灯照射下，非均相光Fenton体系能够有效地降解结构稳定的阳离子红GTL，在pH 6，反应温度20℃，时间90 min，Ce-Fe/Al₂O₃ 2 g/L，H₂O₂浓度340 mg/L，含50 mg/L阳离子红GTL模拟废水TOC去除率为92.40%；光Fenton反应中Fe(Ⅲ)转化为Fe(Ⅱ)。     

H2O2溶液同时脱硫脱硝实验研究

二氧化硫和氮氧化物是电厂产生的主要大气污染物,研究焦点越来越集中在在一个反应器内实现同时脱硫脱硝。实验以H₂O₂溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,实验结果表明：H₂O₂浓度、反应温度、NO浓度、SO₂浓度、烟气流量对脱除率影响显著,pH、氧含量对脱硝率影响不大。在整个实验范围内脱硫效率总是保持在98.5%以上,脱硝效率最高达到67.4%。     

MnOx/Al-SBA-15催化剂低温NH3选择性催化还原NO的原位红外研究简

用原位红外分别进行了MnO_x/Al-SBA-15催化剂上NH₃和NO+O₂的吸附态和瞬态实验以及NH₃+NO+O₂反应的稳态实验。结果表明,催化剂上存在着L酸位和B酸位,NH₃吸附在催化剂上形成配位态的NH₃和NH₄⁺,配位态的NH₃能脱氢形成—NH₂活性中间态。NO+O₂在催化剂上吸附形成硝酸盐类、硝基类和亚硝酸盐类。将NO+O₂通入预吸附NH₃的催化剂中时,表面的配位态的NH₃、NH₄⁺和—NH₂都会减少直至消失,SCR反应显著。而将NH₃通入预吸附NO+O₂的催化剂中时,只有硝基类和亚硝酸盐类减少,硝酸盐类基本不发生变化,SCR反应微弱。NH₃+NO+O₂稳态反应中,催化剂表面稳定存在着NH₄⁺和硝酸盐类,SCR反应显著。     

CaCl2高温热处理垃圾焚烧飞灰中重金属的挥发特性

以深圳市某垃圾焚烧厂飞灰为原料,采用高温管式电阻炉,研究了在0.6 L/min N₂气氛下,CaCl₂在不同添加量、处理温度及处理时间下对飞灰中重金属Pb、Cd、Zn和Cu挥发特性的影响,并对收集到的二次飞灰进行成分及物相分析。结果显示,X射线衍射仪和EDS分析表明,二次飞灰主要是由NaCl、KCl和部分SiCl₄组成,Zn主要以K₂ZnCl₄形式挥发,而Pb则主要以氧化物PbO和Pb₃SiO₅的形式挥发。最终得到CaCl₂热处理飞灰的最佳二次气化条件:以0.6 L/min N₂为载气,添加14 wt%的CaCl₂,在1 100℃高温下处理2.5 h。经CaCl₂热处理后的剩余飞灰,其浸出毒性达到了《生活垃圾填埋场污染控制标准》要求。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.