Aerosol ion characteristics during the Big Bend Regional Aerosol and Visibility Observational study

The ionic compositions of particulate matter with aerodynamic diameter < or = 2.5 microm (PM2.5) and size-resolved aerosol particles were measured in Big Bend National Park, Texas, during the 1999 Big Bend Regional Aerosol and Visibility Observational study. The ionic composition of PM2.5 aerosol was dominated by sulfate (SO4(2-)) and ammonium (NH4+). Daily average SO4(2-) and NH4+ concentrations were strongly correlated (R2 = 0.94). The molar ratio of NH4+ to SO4(2-) averaged 1.54, consistent with concurrent measurements of aerosol acidity. The aerosol was observed to be comprised of a submicron fine mode consisting primarily of ammoniated SO4(2-) and a coarse particle mode containing nitrate (NO3-). The NO3- appears to be primarily associated with sea salt particles where chloride has been replaced by NO3-, although formation of calcium nitrate (Ca(NO3)2) is important, too, on several days. Size-resolved aerosol composition results reveal that a size cut in particulate matter with aerodynamic diameter < or = 1 microm would have provided a much better separation of fine and coarse aerosol modes than the standard PM2.5 size cut utilized for the study. Although considerable nitric acid exists in the gas phase at Big Bend, the aerosol is sufficiently acidic and temperatures sufficiently high that even significant future reductions in PM2.5 SO4(2-) are unlikely to be offset by formation of particulate ammonium nitrate in summer or fall.     

Application of the Tracer-Aerosol Gradient Interpretive Technique to Sulfur Attribution for the Big Bend Regional Aerosol and Visibility Observational Study

Abstract

A simple data analysis method called the Tracer-Aerosol Gradient Interpretive Technique (TAGIT) is used to attribute particulate S and SO₂ at Big Bend National Park in Texas and nearby areas to local and regional sources. Particulate S at Big Bend is of concern because of its effects on atmospheric visibility. The analysis used particulate S, SO₂ , and perfluorocarbon tracer data from six 6-hr sampling sites in and near Big Bend National Park. The data were collected in support of the Big Bend Regional Aerosol and Visibility Observational (BRAVO) Study; the field portion was conducted from July through October 1999. Perfluorocarbon tracer was released continuously from a tower at Eagle Pass, TX, approximately 25 km northeast of two large coal-fired power plants (Carbon I and II) in Coahuila, Mexico, and approximately 270 km east-southeast of Big Bend National Park.

The perfluorocarbon tracer did not properly represent the location of the emissions from the Carbon power plants for individual 6-hr sampling periods and attributed only 3% of the particulate S and 27% of the SO₂ at the 6-hr sites in and near Big Bend to sources represented by the tracer. An alternative approach using SO₂ to tag “local” sources such as the Carbon plants attributed 10% of the particulate S and 75% of the SO2 at the 6-hr sites to local sources. Based on these two approaches, most of the regional (65–86%) and a small fraction (19–31%) of the local SO₂ was converted to particulate S. The analysis implies that substantial reductions in particulate S at Big Bend National Park cannot be achieved by only reducing emissions from the Carbon power plants; reduction of emissions from many sources over a regional area would be necessary.     

Reconciliation and interpretation of Big Bend National Park particulate sulfur source apportionment: results from the Big Bend Regional Aerosol and Visibility Observational Study--part I

The Big Bend Regional Aerosol and Visibility Observational (BRAVO) study was an intensive monitoring study from July through October 1999 followed by extensive assessments to determine the causes and sources of haze in Big Bend National Park, located in Southwestern Texas. Particulate sulfate compounds are the largest contributor of haze at Big Bend, and chemical transport models (CTMs) and receptor models were used to apportion the sulfate concentrations at Big Bend to North American source regions and the Carbón power plants, located 225 km southeast of Big Bend in Mexico. Initial source attribution methods had contributions that varied by a factor of > or =2. The evaluation and comparison of methods identified opposing biases between the CTMs and receptor models, indicating that the ensemble of results bounds the true source attribution results. The reconciliation of these differences led to the development of a hybrid receptor model merging the CTM results and air quality data, which allowed a nearly daily source apportionment of the sulfate at Big Bend during the BRAVO study. The best estimates from the reconciliation process resulted in sulfur dioxide (SO2) emissions from U.S. and Mexican sources contributing approximately 55% and 38%, respectively, of sulfate at Big Bend. The distribution among U.S. source regions was Texas, 16%; the Eastern United States, 30%; and the Western United States, 9%. The Carbón facilities contributed 19%, making them the largest single contributing facility. Sources in Mexico contributed to the sulfate at Big Bend on most days, whereas contributions from Texas and Eastern U.S. sources were episodic, with their largest contributions during Big Bend sulfate episodes. On the 20% of the days with the highest sulfate concentrations, U.S. and Mexican sources contributed approximately 71% and 26% of the sulfate, respectively. However, on the 20% of days with the lowest sulfate concentrations, Mexico contributed 48% compared with 40% for the United States.     

Source profiles for industrial, mobile, and area sources in the Big Bend Regional Aerosol Visibility and Observational study

Representative PM2.5 and PM10 source emissions were sampled in Texas during the Big Bend Regional Aerosol Visibility and Observa (BRAVO) study. Chemical source profiles for elements, ions, and carbon fractions of 145 samples are reported for paved and unpaved road dust, soil dust, motor vehicle exhaust, vegetative burning, four coal-fired power stations, an oil refinery catalytic cracker, two cement kilns, and residential meat cooking. Several samples were taken from each emitter and source type, and these were averaged by source type, and in source subgroups based on commonality of chemical composition. The standard deviation represents the variability of the chemical mass fractions. BRAVO profiles differed in some respects from profiles measured elsewhere. High calcium abundances in geological dust, high selenium abundances in coal-fired power stations, and high antimony abundances in oil refinery catalytic cracker emissions were found. Abundances of eight thermally evolved carbon fractions [Atmos. Environ. 28 (15) (1994) 2493] differ among combustion sources, and a Monte Carlo simulation demonstrates that these differences are sufficient to differentiate among several carbon-emitters.     

Reconciliation and interpretation of the Big Bend National Park light extinction source apportionment: results from the Big Bend Regional Aerosol and Visibility Observational Study--part II

The recently completed Big Bend Regional Aerosol and Visibility Observational (BRAVO) Study focused on particulate sulfate source attribution for a 4-month period from July through October 1999. A companion paper in this issue by Schichtel et al. describes the methods evaluation and results reconciliation of the BRAVO Study sulfate attribution approaches. This paper summarizes the BRAVO Study extinction budget assessment and interprets the attribution results in the context of annual and multiyear causes of haze by drawing on long-term aerosol monitoring data and regional transport climatology, as well as results from other investigations. Particulate sulfates, organic carbon, and coarse mass are responsible for most of the haze at Big Bend National Park, whereas fine particles composed of light-absorbing carbon, fine soils, and nitrates are relatively minor contributors. Spring and late summer through fall are the two periods of high-haze levels at Big Bend. Particulate sulfate and carbonaceous compounds contribute in a similar magnitude to the spring haze period, whereas sulfates are the primary cause of haze during the late summer and fall period. Atmospheric transport patterns to Big Bend vary throughout the year, resulting in a seasonal cycle of different upwind source regions contributing to its haze levels. Important sources and source regions for haze at Big Bend include biomass smoke from Mexico and Central America in the spring and African dust during the summer. Sources of sulfur dioxide (SO2) emissions in Mexico, Texas, and in the Eastern United States all contribute to Big Bend haze in varying amounts over different times of the year, with a higher contribution from Mexican sources in the spring and early summer, and a higher contribution from U.S. sources during late summer and fall. Some multiple-day haze episodes result from the influence of several source regions, whereas others are primarily because of emissions from a single source region.     

Aerosol size distributions and visibility estimates during the Big Bend regional aerosol and visibility observational (BRAVO) study

The Big Bend Regional Aerosol and Visibility Observational (BRAVO) study was conducted in Big Bend National Park in 1999. The park is located in a remote region of southwest Texas but has some of the poorest visibility of any Class 1 monitored area in the western US. The park is frequently influenced by air masses carrying emissions from Mexico and eastern Texas. Continuous physical, optical and chemical aerosol measurements were performed in an effort to understand the sources of and contributions to haze in the park. As part of this characterization, dry aerosol size distributions were measured over the size range of 0.05<D_p<20 μm. Three instruments with different measurement techniques were used to cover this range. Complete size distributions were obtained from all of the instruments in terms of a common measure of geometric size using a new technique. Size parameters for accumulation and coarse particle modes were computed and demonstrate periods when coarse mode volume concentrations were significant, especially during suspected Saharan dust episodes in July and August. Study average (and one standard deviation) geometric volume mean diameters for the accumulation and coarse particle modes were 0.26±0.04 and 3.4±0.8 μm, respectively. Dry light scattering coefficients (b_sp) were computed using measured size distributions and demonstrated periods when contributions to b_sp from coarse particles were significant. The study average computed b_sp was 0.026±0.016 km⁻¹. Computed dry b_sp values were highly correlated with measured values (r²=0.97). Real-time sulfate measurements were correlated with accumulation mode volume concentrations (r²=0.89) and computed dry light scattering coefficients (r²=0.86), suggesting sulfate aerosols were the dominant contributor to visibility degradation in the park.     

A Critical Assessment of Atmospheric Visibility and Aerosol Measurements in the Eastern United States

As part of a study examining the technical basis for a secondary national ambient air quality standard for fine particulate matter to protect visibility, we reviewed available data on atmospheric aerosol and visibility in the eastern U.S. This paper presents the results of that visibility and aerosol characterization.

Analysis of airport visibility data indicates that the annual median visual ranges in the East are in the 16-25 km range. In the absence of a "reference method," limited measurements of visibility using various types of instruments provide data generally in agreement with the airport visibility estimates when a contrast threshold of 0.05 is assumed in calculating visual range from the instrumental measurements.

Both long- and short-term aerosol measurements have yielded consistent results; however, because of the differences in instrumentation and laboratory analytical techniques among various studies, data often are not directly comparable. The measured annual average fine particulate matter mass concentration is about 18 μg/m³ in the rural East; during summer it increases to about 23 μg/m³. If all the sulfur in the fine mass is assumed to exist as ammonium sulfate, it would constitute 46 percent of the annual mean and about 60 percent of the summer mean fine mass concentrations. Carbon and volatiles, including water, are believed to constitute significant fractions of the fine mass; however, there are little data quantifying their contributions to fine mass and visibility impairment. Additional long-term measurements of visibility and fine aerosol and its various components are necessary to completely characterize visibility and aerosol in the East.     

Estimates of particle hygroscopicity during the Southeastern Aerosol and Visibility Study

Aerosol water content was determined from relative humidity controlled optical particle counter (ASASP-X) size distribution measurements made during the Southeastern Aerosol and Visibility Study (SEAVS) in the Great Smoky Mountains National Park during summer 1995. Since the scattering response function of the ASASP-X is sensitive to particle refractive index, a technique for calibrating the ASASP-X for any real refractive index was developed. A new iterative process was employed to calculate water mass concentration and wet refractive index as functions of relative humidity. Experimental water mass concentrations were compared to theoretically predicted values assuming only ammonium sulfate compounds were hygroscopic. These comparisons agreed within experimental uncertainty. Estimates of particle hygroscopicity using a rural aerosol model of refractive index as a function of relative humidity demonstrated no significant differences from those made with daily varying refractive index estimates. Although aerosol size parameters were affected by the assumed chemical composition, forming ratios of these parameters nearly canceled these effects.     

Estimates of Particle Hygroscopicity during the Southeastern Aerosol and Visibility Study

ABSTRACT

Aerosol water content was determined from relative humidity controlled optical particle counter (ASASP-X) size distribution measurements made during the Southeastern Aerosol and Visibility Study (SEAVS) in the Great Smoky Mountains National Park during summer 1995. Since the scattering response function of the ASASP-X is sensitive to particle refractive index, a technique for calibrating the ASASP-X for any real refractive index was developed. A new iterative process was employed to calculate water mass concentration and wet refractive index as functions of relative humidity. Experimental water mass concentrations were compared to theoretically predicted values assuming only ammonium sulfate compounds were hygroscopic. These comparisons agreed within experimental uncertainty. Estimates of particle hygroscopicity using a rural aerosol model of refractive index as a function of relative humidity demonstrated no significant differences from those made with daily varying refractive index estimates. Although aerosol size parameters were affected by the assumed chemical composition, forming ratios of these parameters nearly canceled these effects.     

Development of a PM2 5 Emissions Inventory for the South Coast Air Basin

ABSTRACT

With the promulgation of a national PM_2.5 ambient air quality standard, it is important that PM_2.5 emissions inventories be developed as a tool for understanding the magnitude of potential PM2.5 violations. Current PM₁₀ inventories include only emissions of primary particulate matter (1 ^ï PM), whereas, based on ambient measurements, both PM₁₀ and PM2.5 emissions inventories will need to include sources of both 1^ï PM and secondary particulate matter (2^ï PM). Furthermore, the U. S. Environmental Protection Agency’s (EPA) current edition of AP-42 includes size distribution data for 1o PM that overestimate the PM_2.5 fraction of fugitive dust sources by at least a factor of 2 based on recent studies.

This paper presents a PM_2.5 emissions inventory developed for the South Coast Air Basin (SCAB) that for the first time includes both 1^ï PM and 2^ï PM. The former is calculated by multiplying PM₁₀ emissions estimates by the PM_2.5/PM₁₀ ratios for different sources. The latter is calculated from estimated emission rates of gas-phase aerosol precursor and gas to aerosol conversion rates consistent with the measured chemical composition of ambient PM_2.5 concentrations observed in the SCAB. The major finding of this PM_2.5 emissions inventory is that the ^2ï aerosol component is more than twice the ^1ï aerosol component, which may result in widely different control strategies being required for fine PM and coarse PM.     

Development and Use of a Disaggregated Emissions Inventory for Air Quality Planning in Washington,DC

The Metropolitan Washington Council of Governments (COG) is responsible for developing an Air Quality Plan which will produce attainment of the O₃ and 8 h CO standards in the Washington area by 1987. In order to define as precisely as possible the sources of emissions in the area, a disaggregated emissions inventory was prepared. For mobile sources, this included classification of vehicle type, portion of the trip cycle, and purpose of trip. For nonhighway sources, individual source types were identified. All emissions were assigned to 5 km × 5 km grids and summed to obtain local, state, and/or regional totals. The inventory, although expensive and time-consuming, is a useful tool for decision makers who are responsible for implementing measures to control emissions.     

Assessment of the Nested Grid Model Estimates for Driving Regional Visibility Models in the Southwestern United States

ABSTRACT

The Nested Grid Model (NGM) is a primitive-equation meteorological model that is routinely exercised over North America for forecasting purposes by the National Meteorological Center. While prognostic meteorological models are being increasingly used to drive air quality models, their use in conducting annual simulations requires significant resources. NGM estimates of wind fields and other meteorological variables provide an attractive alternative since they are typically archived and readily available for an entire year. Preliminary evaluation of NGM winds during the summer of 1992 for application to the region surrounding the Grand Canyon National Park showed serious shortcomings. The NGM winds along the borders between California, Arizona and Mexico tend to be northwesterly with a speed of about 6 m/sec, while the observed flow is predominantly southerly at about 2-5 m/sec. The mesoscale effect of a thermal low pressure area over the highly heated Southern California and western Arizona deserts does not appear to be represented by the NGM because of its coarse resolution and the use of sparse observations in that region. Tracer simulations and statistical evaluation against special high resolution observations of winds in the southwest United States clearly demonstrate the northwest bias in NGM winds and its adverse effect on predictions of an air quality model. The “enhanced” NGM winds, in which selected wind observations are incorporated in the NGM winds using a diagnostic meteorological model provide additional confirmation on the primary cause of the northwest bias. This study has demonstrated that in situations where limited resources prevent the use of prognostic meteorological models, previously archived coarse resolution wind fields in which additional observations are incorporated to correct known biases provide an attractive option.     

Development of the crop residue and rangeland burning in the 2014 National Emissions Inventory using information from multiple sources

Biomass burning has been identified as an important contributor to the degradation of air quality because of its impact on ozone and particulate matter. One component of the biomass burning inventory, crop residue burning, has been poorly characterized in the National Emissions Inventory (NEI). In the 2011 NEI, wildland fires, prescribed fires, and crop residue burning collectively were the largest source of PM_2.5. This paper summarizes our 2014 NEI method to estimate crop residue burning emissions and grass/pasture burning emissions using remote sensing data and field information and literature-based, crop-specific emission factors. We focus on both the postharvest and pre-harvest burning that takes place with bluegrass, corn, cotton, rice, soybeans, sugarcane and wheat. Estimates for 2014 indicate that over the continental United States (CONUS), crop residue burning excluding all areas identified as Pasture/Grass, Grassland Herbaceous, and Pasture/Hay occurred over approximately 1.5 million acres of land and produced 19,600 short tons of PM_2.5. For areas identified as Pasture/Grass, Grassland Herbaceous, and Pasture/Hay, biomass burning emissions occurred over approximately 1.6 million acres of land and produced 30,000 short tons of PM_2.5. This estimate compares with the 2011 NEI and 2008 NEI as follows: 2008: 49,650 short tons and 2011: 141,180 short tons. Note that in the previous two NEIs rangeland burning was not well defined and so the comparison is not exact. The remote sensing data also provided verification of our existing diurnal profile for crop residue burning emissions used in chemical transport modeling. In addition, the entire database used to estimate this sector of emissions is available on EPA’s Clearinghouse for Inventories and Emission Factors (CHIEF, http://www3.epa.gov/ttn/chief/index.html).Implications: Estimates of crop residue burning and rangeland burning emissions can be improved by using satellite detections. Local information is helpful in distinguishing crop residue and rangeland burning from all other types of fires.     

The Development of a Model to Examine Source-Receptor Relationships for Visibility on the Colorado Plateau

This paper describes the development and application of the Visibility and Haze in the Western Atmosphere (VISHWA) model to understand the source-receptor relationships that govern chemical species relevant to visibility degradation in the western United States. The model was developed as part of a project referred to as Visibility Assessment for Regional Emission Distributions (VARED), the objective of which is to estimate the contributions of various geographical regions, compounds, and emission

sources to light scattering and absorption by particles on the Colorado Plateau.

The VISHWA model is a modified version of a comprehensive Eulerian model, known as the Acid Deposition and Oxidant Model.1 The modifications were designed to obtain the computational efficiency required to simulate a one-year period at about 1/25th of real time, and at the same time incorporate mechanistic features relevant to realistic modeling of the fate and transport of visibility degrading species. The modifications included use of a condensed chemical mechanism; incorporation of reactions to simulate the formation of secondary organic particles; and use of a semi-Lagrangian advection scheme to preserve concentration peaks during advection.

The model was evaluated with 1992 air quality data from Project MOHAVE (Measurements of Haze and Visual Effects) intensive experiments. An important conclusion of this evaluation is that aqueous-phase oxidation of SO2 to sulfate in nonprecipitating clouds makes a significant contribution to observed sulfate levels during winter as well as summer. Model estimates of ambient sulfate

for the winter intensive were within a factor of 2 of the observations for 75% of the values. The corresponding statistic for the summer intensive was 90%. Model estimates of carbon were within a factor of 2 of the limited set of observations.     

Development of a Dynamic Aquatic Model (DynA Model): Estimating Temporal Emissions of DDT to Lake Maggiore (N. Italy)

- DOI: http://dx.doi.org/10.1065/espr2006.01.009 Background, Aims and Scope Most existing models used to describe the fate of chemicals in surface water and sediment generally consider a 'static scenario', in which a contaminant is discharged at a constant rate and environmental input parameters do not change during the simulation time. This approach is not suitable in environmental scenarios characterized by daily or periodic changes of several input parameters. The aim of this study is to estimate approximate emissions of DDT lo Lake Maggiore using a new surface water model, (DynA Model) that describes the fate of a chemical in a dynamic scenario. Methods The model is developed on the grounds of an existing and validated model (QWASI). A numerical solution was adopted to build the fully dynamic version of the model. Results and Discussion The model was applied to Lake Maggiore emitting DDT at a constant rate until steady-state was reached. Emissions were stopped and later sporadic 'pulse' emissions were added. This was done to calculate the amount of DDT needed to simulate concentrations close to those measured in water and sediments. This allowed the evaluation of the order of magnitude of emissions. An uncertainty analysis for sediment resuspension was also performed, given the lack of measured resuspension rates. Conclusion The model showed the time response of the Lake Maggiore system to varying emission scenarios and provided what are regarded as reasonable estimates of DDT emissions. The model demonstrated the importance of sediment-water exchange. Recommendation and Outlook In order to better calculate DDT concentrations the model should be run with different discharge scenarios to clarify the time trends of concentrations, possibly with the use of different sets of measured data (such as biota and sediment deposition/resuspension rates).     

Development of a regional oxidant model and application to the northeastern United States

Elevated oxidant concentrations due to the long-range transport of ozone and its precursors have been observed in many rural areas in the continental United States. The oxidation processes associated with ozone formation in the atmosphere have many important implications for regional air quality problems, such as regional haze and acid deposition. This paper describes the development and evaluation of a mesoscale photochemical air quality simulation model (RTM-III) covering the northeastern United States. The model considers an area 2080 km in the E-W direction by 1840 km in the N-S direction, with a spatial resolution on the order of 80 x 80 km, and a temporal resolution on the order of one hour. Data collected during an episode in July 1978 by the EPRI Sulfate Regional Experiment is used for testing and evaluating the model. In a comparison of hourly predictions with observations, the model predictions, with a few exceptions where local influences are suspected, generally track the measured spatial pattern and diurnal variation of ozone concentrations quite well. The correlation coefficient matched by time and location over more than 1500 pairs of hourly predicted and observed ozone concentrations is 0.7.     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.