3,5-二硝基水杨酸表面修饰纳米Ti2吸附对硝基苯酚

化学吸附法合成3,5-二硝基水杨酸表面修饰的TiO₂纳米粒子,TiO₂表面修饰后呈浅黄色,TiO₂表面羟基与3,5-二硝基水杨酸发生类似于醇和酸间的酯化反应.表层链接有苯环,极性减弱,非极性增强,在水、苯、乙醇中均分散性良好,与芳香族污染物的亲合力增强,有利于吸附去除芳香族污染物.表面修饰的TiO₂纳米粒子20mg,在最佳吸附pH值3、吸附时间10min,对100mL对硝基苯酚(3～10 mg/L)的吸附率可由改性前的43%增至99.9%.该法吸附效率高,可直接达到一级排放标准,提供了深度处理对硝基苯酚废水的新方法.     

水热合成温度对纳米TiO2特性及其可见光波段光催化性能的影响

以乙醇-丙酮-吡啶为溶剂，采用水热法制备了在可见光波段（≤450nm）具有良好光催化活性的纳米TiO2粉体,通过XRD、TEM、DTA、漫反射谱（DRS）与光电压谱等手段，研究了水热合成温度及250℃热处理对合成纳米TiO2粉体的材料特性，以及在可见光激发下纳米TiO2对甲基橙光催化降解的影响．结果显示，纳米TiO2晶型（锐钛矿）与粒径不随水热合成温度及热处理（250℃）条件的变化发生明显改变；各样品的表面吸附物状态以及可见光响应特性在未经热处理时随水热合成温度变化发生明显变化，而在经250℃热处理后则差异不明显；样品的表面吸附物状态、可见光响应以及可见光催化活性之间有显著关联，水热合成温度显著地影响了纳米TiO2粉体的表面吸附物状态及可见光催化活性。     

金属泡沫镍负载纳米TiO2光催化降解空气中甲醛

研究金属泡沫镍表面负载改性TiO2光催化剂对室内空气主要污染物甲醛的降解。采用溶胶一凝胶法制备了掺杂金属离子的纳米TiO2光催化剂，将其负载于泡沫镍板上，以室内空气典型污染物甲醛为模型反应物，研究3种不同改性纳米TiO2对甲醛的光催化作用．并讨论金属镧离子的最佳掺杂比例以及环境因素对光催化效率的影响。同时考察催化剂的失活特征。结果表明，该负载型纳米光催化剂对甲醛气体具有较高的光催化活性。掺镧TiO2对甲醛的降解率最高。最佳掺杂比例为1．5％。该催化剂存在失活现象。但在清洁后能够恢复。     

降解空气有机污染物纳米涂料的初步研究

用溶胶-凝胶法制备了纯TiO2和掺杂改性TiO2纳米溶胶涂料,并用浸-拉法把此纳米涂料涂覆于基体表面。掺杂改性与未改性TiO2纳米溶胶涂料的结构用X射线衍射仪(XRD)进行了分析,纳米表面形貌用透射电子显微镜(TEM)进行了观测,并进行了在可见光下降解丙酮的实验研究。实验结果表明:掺杂适量的Ce离子对TiO2进行改性,制备的纳米涂料能够一定程度上在可见光下降解空气污染物。     

纳米TiO2的表面改性及在聚氯乙烯中的应用研究

研究了原位乳液共聚合方法制备聚丙烯酸酯/TiO2纳米复合材料及其对PVC抗紫外光老化性能的影响.结果表明,聚丙烯酸酯共聚物P(MMA-BA)包覆在纳米TiO2表面,并与TiO2粒子有较强相互作用;经过1032 h加速老化后,相比未改性配方和有机紫外吸收剂改性配方,复合改性PVC材料的抗紫外光老化性能得到大幅提高,纳米TiO2的质量分数为1.0%的复合材料改性PVC色差值只有5.0,比未改性配方提高近8倍.     

改性污泥基生物炭的制备及其对Cd2+的吸附特性研究

为了提高废水中Cd~(2+)的去除效率并获得高效、低成本吸附剂,以市政污泥为原料,在300℃和500℃条件下限氧热解制备生物炭(BC300和BC500)并用NaOH进行改性(NC300和NC500)。通过元素分析、扫描电镜和傅里叶红外光谱等方法对污泥基生物炭进行表征,运用吸附动力学和吸附等温线系统研究了改性前后污泥基生物炭对Cd~(2+)的吸附特性。结果表明:与未改性的污泥基生物炭相比,改性污泥基生物炭的极性降低,疏水性增强;碱改性炭表面具有更多的-CH_2-,C=O和C-O等官能团,有利于水体中Cd~(2+)的吸附; 4种污泥基生物炭对Cd~(2+)的吸附过程符合准二级动力学方程和Freundlich等温吸附模型,NC300和NC500对于Cd~(2+)的最大平衡吸附量较改性前分别提高了2倍和1.1倍。     

纳米隔热涂料用纳米TiO2的表面改性研究

以硅烷偶联剂为改性剂，通过实验研究了纳米TiO2有机化表面改性的影响因素。结果表明，硅烷偶联剂用量为15%、二氯甲烷作为溶剂、改性时间为2h，改性后的纳米TiO2的表面由亲水性转变为亲油性，并能较好地分散于甲苯中，能满足纳米隔热涂料的制备。     

纳米材料的表面修饰和表征技术

介绍了纳米粒子的表面改性及表面修饰的目的和方法,并对纳米微粒表面改性的各种方法原理及其特点进行了归纳;对纳米材料的常用分析和表征技术做了概括,主要从纳米颗粒的粒度测量、纳米微粒的表面分析、成分分析等方面进行了简要阐述;对纳米材料的表面修饰和表征技术的发展进行了展望。     

纳米Au/TiO2薄膜真空紫外光催化降解甲醛

为提高真空紫外光催化对甲醛的去除率并降低副产物O3的浓度,采用低温吸附法在TiO2薄膜上负载纳米Au.研究比较了UV254nm光催化(TiO2/UV)、真空紫外光降解(VUV)、真空紫外光催化(TiO2/VUV)等3种方法对低浓度甲醛的降解效果.结果表明,TiO2/VUV对甲醛的去除率显著高于VUV和TiO2/UV.TiO2表面负载纳米Au粒子能促进光生电子和空穴的分离.因此,在真空紫外光催化降解过程中, Au/TiO2不仅提高甲醛的降解率,还显著分解副产物臭氧,使尾气臭氧浓度降低32%.而且Au/TiO2薄膜在真空紫外光催化过程中具有很好的稳定性.     

煅烧结合光辐照提高纳米AgI/TiO_2的可见光响应

为提高AgI/TiO2的可见光响应能力,采用煅烧结合光辐照的工艺对其进行改性.紫外-可见光吸收分析表明,改性AgI/TiO2的敏感光谱范围覆盖了整个可见区,吸收边带从465nm红移至800nm,在500nm处的吸光度提高了近3倍.X-射线衍射分析结果指出,煅烧提高了金红石型TiO2的相对含量,导致禁带宽度从2.89eV降到2.81eV,氙灯辐照进一步增加了锐钛型TiO2、金红石型TiO2和AgI的相对含量,并生成了新的晶体AgCl,使其禁带宽度又降至1.55eV左右.AgCl的产生、AgI和金红石型TiO2相对含量的增加是降低改性材料禁带宽度和增强可见光响应能力的主要原因.研究还表明,只有煅烧后的AgI/TiO2才能通过光辐照来拓宽可见光敏感范围,而且,光辐照中起作用的主要是紫外光,可见光的作用甚小.研究最后提出将2种或2种以上的卤化银负载在纳米TiO2上,更能有效地增强TiO2的可见光响应能力.     

Conversion regular patterns of acetic acid, propionic acid and butyric acid in UASB reactor

On the basis of continuous tests and batch tests, conversion regular patterns of acetate, propionate and butyrate in activated sludge at different heights of the UASB reactor were conducted. Results indicated that the conversion capacity of the microbe is decided by the substrate characteristic when sole VFA is used as the only substrate. But when mixed substrates are used, the conversion regulations would have changed accordingly.Relationships of different substrates vary according to their locations. In the whole reactor, propionate‘s conversion is restrained by acetate and butyrate of high concentration. On the top and at the bottom of the reactor, conversion of acetate, but butyrate, is restrained by propionate. And in the midst, acetate‘s conversion is accelerated by propionate while that of butyrate is restrained. It is proved, based on the analysis of specific conversion rate, that the space distribution of the microbe is the main factor that affects substrates‘ conversion. The ethanol-type fermentation of the acidogenicophase is the optimal acid-type fermentation for the two-phase anaerobic process.     

PASP、PAA与PBTCA阻垢性能的对比实验研究

采用静态阻垢法研究了聚天冬氨酸(PASP)、聚丙烯酸(PAA)和2-膦酸基丁烷-1,2,4-三羧酸(PBTCA)对碳酸钙和硫酸钙的阻垢性能,并用旋转挂片法研究了3种阻垢剂作用下湿法石灰脱硫浆液系统的结垢规律.研究发现:随着阻垢剂浓度的增加,3种阻垢剂都表现出溶限效应;相同实验条件下,3种阻垢剂对碳酸钙的静态阻垢性能表现为PBTCA>PAA>PASP;对中性和碱性环境,pH对阻垢剂阻硫酸钙垢的性能影响较小;随着温度的升高和反应时间的延长,3种阻垢剂阻硫酸钙的阻垢率先增大后减小;对湿法石灰脱硫浆液系统,3种阻垢剂作用下,单位面积挂片上的结垢量均是随着阻垢剂质量浓度的增大先增大后减小,在浓度达到30mg/L时,挂片上的结垢量都很小.     

邻苯二甲酸和苯甲酸在功能化碳纳米管上的吸附行为

在pH7.0的条件下,采用批量平衡方法研究邻苯二甲酸（PA）和苯甲酸（BA）在3种不同功能化碳纳米管（羟基化H-CNTs、羧基化C-CNTs和石墨化G-CNTs）上的吸附/解吸行为,并进一步探究共存BA对PA在碳纳米管上吸附的影响.结果表明,Langmuir和Freundlich模型均可对PA和BA在3种碳纳米管上的吸附数据进行较好的非线性拟合,其中Freundlich模型拟合效果更好（Adj r²均达到0.88以上）;3种碳纳米管对PA和BA的吸附能力大小均依次为：C-CNTs > H-CNTs > G-CNTs;解吸实验中,C-CNT和H-CNTs对BA和PA的解吸均具有明显的滞后现象,说明BA和PA在C-CNT和H-CNTs上的吸附有较强化学作用力的发生,而G-CNTs对二者的解吸曲线与吸附曲线几乎重合,不具有明显的滞后现象,这与G-CNTs表面缺乏官能团有关;当PA和BA共存在时,以PA为主要吸附质,BA为竞争吸附质,发现在H-CNTs和C-CNTs上,共存BA对PA为竞争作用,而在G-CNTs上,共存BA对PA起协同吸附作用.     

邻苯二甲酸酯及邻苯二甲酸在碳管上的吸附

以邻苯二甲酸（PA）和邻苯二甲酸二乙酯（DEP）为目标污染物,碳纳米管（CNTs）为吸附剂,通过不同pH值条件下单、双溶质的吸附实验,结合能量分布理论,分析PA对DEP在CNTs上的竞争和取代吸附.结果表明,在同一pH值下,DEP在CNTs上的吸附性强于PA.对于DEP,pH值改变导致的CNTs分散稳定性的变化是影响其吸附的决定因素.对于PA,溶液pH值会影响CNTs的表面电荷及PA的解离程度,两者均会产生影响.双溶质体系下,PA对DEP在CNTs上的吸附存在竞争和取代效应.在不同pH值条件下,PA对DEP在CNTs上的竞争和取代的程度与CNTs的分散稳定性和PA的解离程度有关.基于能量分布的分析表明,虽然PA的加入导致DEP在CNTs上可利用的高能吸附位点数量显著下降,但是其可利用的低能吸附位点数量增加.     

Formic acid and acetic acid in the western Sierra Nevada,California

This paper reports the results of measurements of formic and acetic acid at four sites located along the western slope of the Sierra Nevada and compares the results with those of earlier studies. Formic acid concentrations ranged from approximately 1 to 40 ppb; those of acetic acid ranged from approximately 0.5 to 13 ppb. Mean formic acid concentrations were 18 ppb at Tehachapi, located at the southern extremity of the range, and between 12 and 13 ppb at the three other sites. Mean acetic acid concentrations ranged from 3.9 ppb at Blodgett Experimental Forest, located at the northern extremity, to 8.0 ppb at Yosemite. Comparison with previous studies indicates that carboxylic acid levels measured in the Sierra Nevada are higher than those measured in past studies, and in many cases average concentrations of both formic and acetic acids observed during this study were greater than the previously reported maxima. Comparisons were also made to nitric acid concentrations measured at Yosemite and Giant Forest from October 1986 to September 1987. At Yosemite, annual nitric acid concentrations averaged 0.20 ppb during the day, and 0.06 ppb at night; and at Giant Forest, nitric acid averaged 0.17 ppb during the day, and 0.05 ppb at night. Thus, the high formic and acetic acid concentrations observed in this study suggest that carboxylic acid are major contributors to the overall flux of ambient acid deposition in the western Sierra Nevada.     

Biogenetic amino acid antagonists

The mode of action of amino acid antagonists of biological origin ist surveyed und the enzymatic reactions with which these antibiotics interfere are described, thus also elucidating the various roles of amino acids in cell physiology. Several organisms, including the antibiotic producer, possess molecular devices for conferring resistance to some of these substances. These antibiotics may be of further value as research tools in molecular biology.     

Adsorption selectivity of salicylic acid and 5-sulfosalicylic acid onto hypercrosslinked polymeric adsorbents

Both bottle-point and column-feeding experiments involving different solutes and sorbents were carried out to investigate the adsorption selectivity and separation performance of salicylic acid and 5-sulfosalicylic acid. Their adsorption isotherms onto such hypercrosslinked polymeric adsorbents as NDA-100 and NDA-99 could be well described by the Freundlich equations whose characteristics describe extrathermic and favorable adsorption processes. The adsorption towards NDA-100 mainly depended on the π-π interaction, while that towards NDA-99 was extremely influenced by the static-electric interaction. Additionally, the adsorptive capacity of salicylic acid on NDA-99 decreased while it increased on NDA-100 with the presence of 5-sulfosalicylic acid in the adsorptive environment as the competitive component. Comparatively, the adsorption capacity of 5-sulfosalicylic acid decreased on both resins with salicylic acid as the competitive component. In fact, the difference in the interaction between adsorbent and adsorbate resulted in the straight antagonism on the effective adsorption sites on the adsorbent. In conclusion, the adsorption selectivity of salicylic acid onto NDA-100 was obviously larger than that onto NDA-99 with the existence of 5-sulfosalicylic acid in the adsorptive environment. A satisfactory separation and recovery of tested solutes in aqueous phase could be foreseeably achieved by the sequencing adsorption technique involving NDA-100 as well as NDA-99. Translated from Environmental Pollution & Control, 2005, 27(8): 570–574 [译自: 环境污染与防治]     

Effects of fulvic acid and humic acid on aluminum speciation in drinking water

This article focused on the influences of fulvic acid and humic acid on aluminum speciation in drinking water. Factors including the concentration of residual chlorine and pH value had been concerned. Aluminum species investigated in the experiments included inorganic mononuclear, organic mononuclear, mononuclear, polymer, soluble, and suspended forms. It was found that the e ects of fulvic acid and humic acid on aluminum speciation depended mainly on their molecular weight. Fulvic acid with molecular weight less than 5000 Dalton had little influence on aluminum speciation; while fulvic acid with molecular weight larger than 5000 Dalton and humic acid would increase the concentration of soluble aluminum significantly even at concentration below 0.5 mg/L (calculated as TOC). Aluminum species, in the present of fulvic acid with molecular weight larger than 5000 Dalton and humic acid, were more stable than that in the present of fluvic acid with molecular mass less than 5000 Dalton, and varied little with reaction time. Within pH range 6.5–7.5, soluble aluminum increased notably in water with organic matter. As the concentration of residual chlorine increased, the e ects of fulvic acid and humic acid became weak. The reactions between humic acid, fulvic acid with large molecular weight, and aluminum were considered to be a multi-dentate coordination process. With the consideration of aluminum bioavailability, reducing the concentration of fulvic acid and humic acid and keeping the pH value among 6.5–7.5 were recommended during drinking water treatment.