臭氧化降解结晶紫溶液的机理

采用臭氧化法对模拟废水中难生物降解的结晶紫染料进行降解实验研究,藉助紫外光谱、红外光谱、气相色谱、化学需氧量和总有机碳的检测结果对反应机理进行了初步探讨。实验结果表明,当溶液初始质量浓度0.88 mmol/L,臭氧投加量9.06×10-5mol/min,调节初始溶液pH为10.0,控制反应温度298 K,反应120 min后,结晶紫溶液COD去除率达到97.0%。分析表明,结晶紫染料降解的中间产物主要是对氨基苯酚、丁烯二酸、乙酸等有机小分子物质,最终产物为水和二氧化碳。     

Box-Behnken响应曲面优化铁炭微电解降解结晶紫

在单因素实验的基础上,以结晶紫脱色率为评价指标,铁炭比、反应时间与曝气量为考察因素,采用Box-Be-hnken响应曲面法优化铁炭微电解降解结晶紫的工艺条件,同时得出相应的数学模型。实验表明,在结晶紫初始浓度为100mg/L和体积为300 mL,pH为3,反应时间为80 min,铁屑的投加量为20 g,铁炭质量比为2∶1,曝气量为20 L/h的条件下,铁炭微电解对结晶紫的脱色率可达到89.6%。通过Box-Behnken响应曲面可知,铁炭比、反应时间、曝气量以及铁炭比和反应时间的交互作用对结晶紫的脱色率均有显著影响,其中曝气量对脱色率的影响尤为显著;回归模型决定系数R2=0.9067,P=0.039,表明此模型拟合程度良好,且模型显著。铁炭微电解降解结晶紫最佳的工艺条件为:铁炭比为2.4∶1,反应时间为84 min、曝气量为40 L/h,脱色率为93.25%,回归模型的预测值与测定值偏差率为2.26%。     

磁性介孔碳吸附模拟废水中的结晶紫

以磁性介孔碳吸附处理结晶紫染料模拟废水,考察了吸附剂投加量、溶液p H、结晶紫初始浓度以及温度对吸附平衡的影响。结果表明,该吸附不受溶液p H的影响,符合拟二级动力学方程(R20.996)。在不同温度下,吸附过程更符合Langmuir等温方程(R20.997),在45℃时其最大吸附量是151.52 mg/g。该吸附的活化能Ea介于21.93和24.17k J/mol之间,表明该吸附的机理是以化学吸附为主。热力学参数计算结果表明,该吸附是一个熵增的自发吸热过程,提高温度有利于吸附的进行。     

ACF电极电解处理含NaCl结晶紫染料废水的研究

以吸附结晶紫达到饱和的活性炭纤维为阳极,在NaCl介质中对初始浓度为100 mg/L的结晶紫染料废水进行了电解脱色处理。实验考察了NaCl浓度、pH值和电流密度等对溶液脱色率的影响,测定了电解时溶液中生成的游离氯浓度及不同电解时间后溶液的紫外-可见吸收光谱曲线,并对不同电解时间后溶液的归一化吸光度比值进行了计算。结果发现,溶液中所产生的游离氯的浓度随电解时间的增加快速上升,20 min时就几乎达到了最大值;在活性氯的作用下,结晶紫分子中的大π共轭体系被破坏,溶液迅速脱色;电解液中所含的NaCl浓度、电解液的pH值和电流密度等都对脱色率有影响;在一定实验条件下,初始浓度为100 mg/L的结晶紫染料废水在电解60 min后脱色率可高达99.3%。     

Photocatalytic degradation of crystal violet dye under sunlight by chitosan-encapsulated ternary metal selenide microspheres

Environmental Science and Pollution Research - Organic dyes that are extensively released in wastewater from various industries remain the priority concern in the modern world. Therefore, a novel...     

Efficient degradation of crystal violet in magnetic CuFe2O4 aqueous solution coupled with microwave radiation

Nanoscale copper ferrite was prepared by co-precipitation method, while citrate acid assisted method was used as reference. Microwave-induced degradation of crystal violet was performed with synthesized copper ferrite, and the behavior of copper ferrite in this process was studied by X-ray photoelectron spectroscopy, SEM/EDS and vector network analyzer. Microwave radiation could greatly enhance the activity of copper ferrite in organic oxidation. The variant of copper and iron on the surface and in the inner core of copper ferrite was studied here. Copper ferrite presents relatively low dielectric loss. Meanwhile, microwave radiation makes a faster degradation than conventional heating process, indicating an indispensable non-thermal effect of microwave with copper ferrite in the process. Microwave induced holes could be responsible for the efficient degradation. The effect of annealing on crystallization and degradation process was considered here, and the intermediates and products were studied by GC-MS and LC-MS to provide a comprehensively evaluation of degradation.     

基于响应曲面法优化的臭氧/过硫酸盐/四氧化三铁工艺对结晶紫的降解

为有效去除水中结晶紫,利用臭氧/过硫酸盐/四氧化三铁工艺对结晶紫的氧化效果进行研究,设计单因素实验探索臭氧流量、过硫酸盐浓度、四氧化三铁浓度和pH对结晶紫降解的影响,依据响应曲面法的Box-Behnken Design(BBD)实验设计原理,探究臭氧流量、过硫酸盐浓度、四氧化三铁浓度和反应时间对降解效果的影响,并优化工艺参数;使用SEM-EDS、FT-IR和Raman表征了反应前后的四氧化三铁,并用EPR技术直接鉴定出工艺过程中的活性氧。结果表明：此工艺在较宽的pH区间(3~11)都具有较高的结晶紫降解能力,臭氧流量、过硫酸盐浓度和四氧化三铁浓度与结晶紫的降解率成正比;臭氧流量1.000 L·min⁻¹,过硫酸盐浓度0.968 mmol·L⁻¹,四氧化三铁浓度2.158 mmol·L⁻¹,反应时间41.702 min为预测的最佳工艺条件;在最佳工艺条件下得到的实际降解率与预测降解率相对偏差仅为−1.12%;催化反应后Fe₃O₄粒径减小,表面变得更加光滑;反应后的Fe₃O₄的铁元素质量分数由48.24％降至35.31%,而氧和硫元素质量分数由34.05%和0.39%分别增至37.59%和1.09%;臭氧/过硫酸盐/四氧化三铁工艺过程中存在SO₄^·–和·OH。由此可知,BBD优化模型预测与实际处理效果基本一致。该研究成果为可为难降解的结晶紫废水的深度处理提供参考。     

纳米RuO2－TiO2光电催化处理农药废水研究

采用自制的负载型纳米RuO₂－TiO₂光催化剂对农药厂生产废水进行光电催化降解试验。考察了煅烧时间、催化剂用量、光辐照强度、电流密度、废水初始pH值和反应时间对废水COD和色度去除率的影响。结果表明，自制光催化剂光电催化性能显著，最佳光电催化活性是同样降解条件下、同样含量的Degussa P－25 TiO₂的1.38倍，是Ru_0.3Ti_0.7O₂的1.81倍。其COD和色度去除率分别为64.3%和95.2%。     

纳米RuO2-TiO2光电催化处理农药废水研究

采用自制的负载型纳米RuO2-TiO2光催化剂对农药厂生产废水进行光电催化降解试验.考察了煅烧时间、催化剂用量、光辐照强度、电流密度、废水初始pH值和反应时间对废水COD和色度去除率的影响.结果表明,自制光催化剂光电催化性能显著,最佳光电催化活性是同样降解条件下、同样含量的Degussa P-25 TiO2的1.38倍,是Ru0.3Ti07O2的1.81倍.其COD和色度去除率分别为64.3%和95.2%.     

因子设计法优化掺硼金刚石电催化降解染料废水

掺硼金刚石电催化工艺(BDD工艺)作为当前热门的水处理技术,已被成功用于降解多种有机污染物。采用因子设计方法,考查了BDD工艺对偶氮染料金橙-Ⅱ的降解效能。实验选用染料初始浓度、反应时间、电解质浓度、施加电流和流速作为操作参数,并以脱色率作为响应指标来评估各参数的统计学显著性。在考察的5个因素中,前两者对于处理效果具有最为显著的影响。为此,在高因子水平情况下又进一步分析了它们的主效应和相互效应,同时构造了回归模型。实验结果表明,因子设计法对于优化BDD工艺是非常适用的,并显示了其实际应用的前景。     

油茶果壳对水溶液中结晶紫的吸附性能

研究了油茶果壳(COS)对结晶紫的吸附特性,考察了COS用量、pH值对COS吸附性能的影响。结果表明,在COS用量为0.30 g、结晶紫初始浓度为50 mg/L、pH=8.00溶液条件下,室温振荡3 h达到吸附平衡,平衡状态下油茶果壳对结晶紫的去除率达到98.01%。用拟一级动力学模型、拟二级动力学模型和内扩散模型分别对动力学数据进行拟合,结果发现,COS吸附结晶紫的动力学数据符合拟二级动力学模型,结晶紫初始浓度为40 mg/L时速率常数和相关性系数分别为0.0436 L/(mg·min)和0.9999。吸附等温线符合Langmuir吸附等温式,随温度在一定范围内升高,最大吸附量增大,且相关性系数均高于0.99,当T=293 K时COS对结晶紫的最大吸附量为26.932 mg/g。热力学计算结果表明,该吸附过程是一个伴有物理吸附的吸热反应,可自发进行。此外,再生实验结果发现,油茶果壳再生7次后,对结晶紫的去除率仍为95%以上。     

电化学法生成Fenton试剂及其在工业染料废水降解脱色中的应用

以多孔石墨电极为阴极 ,电解时在阴极通以氧气或空气 ,电解生成的过氧化氢与阳极溶解的Fe2 +进行随后化学反应 ,现场生成羟基自由基 (Fenton试剂 ) ,进而对有机染整工业废水进行降解脱色反应。以可见光吸收谱图表征了工业染料废水经电解槽处理后吸光度的变化 ,以重铬酸钾法测试染料处理后的COD。实验结果表明 ,COD的去除率大于 80 % ,染料的脱色率达 1 0 0 % ,若将电解电流密度控制在 1 0mA/cm2 以下 ,槽电压可控制在 5V以内。实验结果表明 ,向阴极多孔石墨电极中通入空气与通入氧气的效果一致。     

Monitoring the photochemical degradation of triclosan in wastewater by UV light and sunlight using solid-phase microextraction

Photo solid-phase microextraction (photo-SPME) is applied for the first time to study the photochemical behavior of an emerging pollutant, triclosan, in real contaminated wastewater samples using a solar simulator. In this study, water samples are extracted by SPME and then, the fiber coating is irradiated for a selected time. This on-fiber procedure, so-called photo-SPME, followed by gas chromatography-mass spectrometry makes it possible to study photodegradation kinetics and the generation of byproducts. Several photoproducts were identified in the real samples including the 2,8-dichlorodibenzo-p-dioxin, dichlorophenols and a compound tentatively identified as other DCDD congener or a dichlorohydroxydibenzofuran. Accordingly, it was possible to postulate main photodegradation mechanisms. Photo-SPME demonstrated slower kinetics in wastewater than in spiked ultrapure water probably due to the presence of dissolved organic matter. This technique was extensively compared with conventional aqueous photodegradation showing high similarity. The influence of pH on the triclosan photolysis and on the triclosan-dioxin conversion was also investigated in wastewater. Photodegradation of triclosan and formation of 2,8-DCDD occurred independently of sample pH. This study represents an advance in the use of photo-SPME to understand the photochemical fate of environmental organic pollutants and demonstrates its clear advantages with real samples.     

Applications of two-phase anaerobic degradation in industrial wastewater treatment

Prospects for the phased anaerobic treatment of wastewater are extremely promising. With the variety of reactor designs available and the amenability of reactors to modification, existing treatment systems may be replaced or upgraded as required to achieve increased stability, higher loading capacities and greater process efficiencies than single-stage systems. In recent times, various reactor configurations and substrates are applied to two-phase anaerobic process. This paper reviews applications and studies of two-phase anaerobic degradation for wastewater treatment, sums up the performance of application to treating waste from distillery, landfill leachate, coffee, cheese whey and dairy, food, pulp and paper, sludge and solid, etc., and summarises reactor configurations, environmental and operational conditions, and comparisons of two-phase anaerobic digestion with other anaerobic reactors.     

Post-treatment of bio-treated acrylonitrile wastewater using UV/Fenton process: degradation kinetics of target compounds

In this study, post-treatment of bio-treated acrylonitrile wastewater was performed using the UV/Fenton process. Five target compounds (furmaronitrile, 3-pyridinecarbonitrile, 1,3-dicyanobenzene, 5-methyl-1H-benzotriazole, and 7-azaindole) were selected as target compounds and their degradation kinetics were examined. Under optimal reaction conditions (H₂O₂ dosage 3.0 mM, Fe²⁺ dosage 0.3 mM, and initial pH 3.0), more than 85% of total organic carbon (TOC) was eliminated in 30 min when a 10-W UV lamp was employed, and the electrical energy per order of magnitude for TOC removal was as low as 2.96 kWh m^?3. Furthermore, the target compounds and the toxicity were largely removed from the bio-treated effluent. Size exclusion chromatography with organic carbon detector analysis revealed that organic components with a wide range of molecular weights were greatly reduced after the UV/Fenton process. A simplified pseudo steady-state (SPSS) model was applied to predict the degradation of target compounds during the UV/Fenton process. The concentrations of generated hydroxyl radicals were estimated to be 3.06 × 10^?12 M, 6.37 × 10^?12 M, and 10.9 × 10^?12 M under 5-, 10-, and 15-W UV lamps, respectively. These results demonstrate that the proposed SPSS model fitted well with experimental data on the post-treatment of real wastewater, and consequently indicate that this model can be a useful tool in the prediction of degradation of target compounds during the UV/Fenton process.

     

Modeling and optimization of reductive degradation of chloramphenicol in aqueous solution by zero-valent bimetallic nanoparticles

Purpose

The present study aims to investigate the individual and combined effects of temperature, pH, zero-valent bimetallic nanoparticles (ZVBMNPs) dose, and chloramphenicol (CP) concentration on the reductive degradation of CP using ZVBMNPs in aqueous medium.

Method

Iron?Csilver ZVBMNPs were synthesized. Batch experimental data were generated using a four-factor statistical experimental design. CP reduction by ZVBMNPs was optimized using the response surface modeling (RSM) and artificial neural network-genetic algorithm (ANN-GA) approaches. The RSM and ANN methodologies were also compared for their predictive and generalization abilities using the same training and validation data set. Reductive by-products of CP were identified using liquid chromatography-mass spectrometry technique.

Results

The optimized process variables (RSM and ANN-GA approaches) yielded CP reduction capacity of 57.37 and 57.10?mg?g^?1, respectively, as compared to the experimental value of 54.0?mg?g^?1 with un-optimized variables. The ANN-GA and RSM methodologies yielded comparable results and helped to achieve a higher reduction (>6%) of CP by the ZVBMNPs as compared to the experimental value. The root mean squared error, relative standard error of prediction and correlation coefficient between the measured and model-predicted values of response variable were 1.34, 3.79, and 0.964 for RSM and 0.03, 0.07, and 0.999 for ANN models for the training and 1.39, 3.47, and 0.996 for RSM and 1.25, 3.11, and 0.990 for ANN models for the validation set.

Conclusion

Predictive and generalization abilities of both the RSM and ANN models were comparable. The synthesized ZVBMNPs may be used for an efficient reductive removal of CP from the water.     

不同前处理方式对铁屑还原降解土壤中对硝基苯酚的影响

为推动铁屑在治理受硝基酚类化合物污染土壤中的实际应用,常温(25±1℃)常压下,利用不同前处理方式处理的铁屑、还原铁粉对土壤中的对硝基苯酚(p-NP)进行了还原降解研究;分析了土壤部分理化性质对p-NP还原效果的影响;并对反应时间、铁屑用量和土壤含水量3个人工易控因素作了最优化选择。结果表明:铁屑和铁粉对p-NP还原降解效果影响的大小顺序为:酸洗铁屑还原铁粉水洗铁屑碱洗铁屑;适中的土壤含水量、偏酸性的土壤初始pH值及较高的土壤有机质含量均可显著提高铁屑对p-NP的还原率;正交实验结果显示反应时间对p-NP还原效果影响最大,铁屑用量次之,土壤含水量最小;处理1.5 g p-NP浓度约为1.3×10-5mol/g的模拟污染土壤的反应最优化条件为:酸洗铁屑用量26 mg,土壤含水量0.35 mL,反应时间130 m in,还原率可达到96.4%。     

硫铁矿烧渣催化类Fenton法深度处理维生素C废水

采用硫铁矿烧渣协同Fe2+催化H2O2的类Fenton法深度处理维生素C制药废水,通过正交实验考察FeSO4投加量、H2O2投加量、搅拌反应时间、曝气时间等因素对低浓度难降解有机物去除的影响程度,并结合单因素实验确定最佳反应条件。结果表明:(1)正交实验中,各因素对催化氧化反应效果的影响程度依次为H2O2投加量搅拌反应时间曝气时间FeSO4投加量;(2)单因素实验中,最佳反应条件为烧渣投加量10g/L、H2O2投加量4.9mmol/L、FeSO4投加量3.9mmol/L、搅拌反应时间20min、曝气时间20min、絮凝沉淀部分聚丙烯酰胺(PAM)投加量5mg/L。在此条件下,COD去除率最高达63.21%。     

TiO2/GeO2复合膜光催化氧化降解农药废水的研究

提出了一种新的TiO2/GeO2复合膜圆形光催化氧化反应器,研究了该反应器对经物化处理后的农药废水进行降解的过程。研究表明,光催化氧化的最佳条件是锌片镀TiO2/GeO2复合膜、pH=6.7、过氧化氢（H2O2）浓度为400 mg/L。并对其他氧化剂对该过程的影响进行了探讨。有机废水通过该反应器处理后,其COD值降为57mg/L。能使有机污染物全部降解为小分子无机物,废水达到国家一级排放标准。     

氮掺杂二氧化钛可见光催化降解曙红Y溶液

采用溶胶凝胶法制备了氮掺杂二氧化钛光催化剂,用XRD、SEM、FTIR和粒度分析仪对催化剂进行了表征,并且在可见光作用下对曙红Y溶液进行了光催化降解实验。研究了催化剂的投加量、曙红Y的初始浓度、光照时间和pH对曙红Y溶液的光降解效果。结果表明,以可见光作光源,催化剂的投入量为0.4 g,曙红Y溶液的初始浓度为20 mg/L,光照时间为50 min,pH=4条件下,曙红Y溶液的降解率达98.87%。