MO_x-CeO_2/HZSM-5催化剂催化氧化含氯挥发性有机物研究

采用浸渍法制备了不同过渡金属掺杂的MOx-CeO2/HZSM-5（M分别表示Cr、Mn、Fe、Co、Ni和Cu）催化剂,研究了各催化剂对1,2-二氯乙烷（DCE）的催化降解性能.结果表明,过渡金属掺杂后,MOx-12%CeO2/HZSM-5催化剂催化氧化1,2-二氯乙烷（DCE）的活性明显提高.各催化剂（记为M-CeO...     

原位合成CuO/ZnO-Al2O3水滑石衍生催化剂催化湿式空气氧化苯酚

采用原位合成法在γ-Al_2O_3表面合成了锌铝水滑石,再采用浸渍法制备了CuO/ZnO-Al_2O_3水滑石衍生催化材料,并将其应用于催化湿式空气氧化苯酚.同时,采用XRD、SEM、BET、H_2-TPR和N_2O滴定等手段对催化剂进行了表征,探讨了CuO含量对CuO/ZnO-Al_2O_3催化剂催化性能的影响.结果表明,当CuO负载量为10%时,催化剂的Cu比表面积最大,催化性能最佳,在200℃、2 MPa空气、苯酚初始浓度500 mg·L~(-1)的条件下,COD去除率为95.3%.     

Fe-Al/Al2O3催化臭氧化去除水中有机污染物2,4-D过程中溴酸盐的生成控制研究

采用浸渍、强化水解和后续水浴加热的方法制得催化剂Fe-Al/Al2O3,并通过XRD和XPS等表征手段对其结构性能进行了研究.结果表明,催化剂中铁是以二价和三价存在,且以三价铁为主;铝则以Al2O3和AlOOH形态存在.与单独臭氧化相比,Fe-Al/Al2 O3既能高效矿化水中的难降解有机物2,4-二氯苯氧乙酸(2,4-D),又能明显抑制溴酸盐的生成,体现出很好的循环使用稳定性.进一步探讨了臭氧投加量和溴离子初始浓度对催化臭氧化效率和溴酸盐生成的影响.研究表明,在Fe-Al/Al2O3催化臭氧化过程中,水中溴酸盐浓度受臭氧投加量和溴离子初始浓度的影响较小,均可明显抑制溴酸盐的生成,且有机物的矿化效率随着臭氧投加量的增加而显著提高.     

电场与MnxCey催化剂在苯氧化反应中的协同效应及机理探究

挥发性有机物（VOCs）大量排放已成为日益严重的环境问题,为了实现VOCs的高效去除,本文采用自蔓延燃烧合成法制备了一系列锰铈复合氧化物催化剂,将稳恒直流电场引入典型VOCs气体苯的催化氧化过程,并基于不同电场条件下催化剂的理化性质表征结果进行机理分析.实验结果表明,Mn_xCe_y催化剂对含苯废气的去除有良好的效果,稳恒直流电场显著促进了催化剂的活性,其中Mn₁Ce₃的催化性能最佳,电流为5 mA时,Mn₁Ce₃催化剂在155℃可达到50%的苯转化率,在202.4℃可达到90%的苯转化率,对应的转化温度T₅₀和T₉₀比传统方法分别降低了62.4℃和48.3℃,且电场中的反应活化能由52.32 kJ·mol^-1降低至32.31 kJ·mol^-1.根据实验现象及表征结果,发现协同效应与活性位点的快速持续再生及活性氧物种的转化有关,由此提出苯在Mn_xCe_y催化剂上的氧化机理及电场协同催化的反应模型.     

Catalytic decomposition performance for O3 and NO2 in humid indoor air on a MnOx/Al2O3 catalyst modified by a cost-effective chemical grafting method

Processes based on non-thermal plasma (NTP) for indoor air treatment inevitably lead to the formation of toxic by-products such as ozone (O₃) and nitrogen oxides (NO_x). Adding a step of heterogeneous catalysis in series with NTP could allow for the decomposition of the by-products. Therefore, different catalysts were developed based on transition metal oxides, such as NiO_x, CoO_x and MnO_x with different weight percentage 1, 5 and 10 wt.%, deposited on a γ-Al₂O₃ support. The O₃ removal efficiency (ORE) and the NO_x removal efficiency (NRE) were very encouraging in dry air: about 65% and 80%, respectively, by using 2 g 5 wt.% MnO_x/Al₂O₃ catalyst under the experimental conditions. However, strongly negative effects of relative humidity (RH) on the catalytic decomposition performance were observed. To overcome this limitation, the catalyst surface was modified to make it hydrophobic using a cost-effective chemical grafting method. This treatment consisted in impregnating the 5 wt.% MnO_x/Al₂O₃ catalyst with different trichloro(alkyl)silanes (TCAS). The effects of different linker lengths and amounts of TCAS for the hydrophobicity and the decomposition performance of surface-modified catalysts under humid conditions were investigated. Our results show that the surface-modified catalyst with the shortest linker and 0.25 mmol/g_cat of modifying agent represents the best catalytic decomposition performance for O₃. Its ORE is 41% at 60% RH, which is twice that of the non-modified catalyst.     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

Enhanced photocatalytic activity of rGO/TiO2 for the decomposition of formaldehyde under visible light irradiation

Due to the low concentration of indoor air contaminants,photocatalytic technology shows low efficiency for indoor air purification.The application of TiO_2 for photocatalytic removal of formaldehyde is limited,because TiO_2 can only absorb ultraviolet(UV) light.Immobilization of TiO_2 nanoparticles on the surface of graphene can improve the visible light photocatalytic activity and the adsorption capacity.In this study,rGO(reduced graphene oxide)/TiO_2 was synthesized through a hydrothermal method using titanium tetrabutoxide and graphene oxide as precursors,and was used for the degradation of low concentration formaldehyde in indoor air under visible light illumination.Characterization of the crystalline structure and morphology of rGO/TiO_2 revealed that most GO was reduced to rGO during the hydrothermal treatment,and anatase TiO_2 nanoparticles(with particle size of 15–30 nm) were dispersed well on the surface of the rGO sheets.rGO/TiO_2 exhibited excellent photocatalytic activity for degradation of formaldehyde in indoor air and this can be attributed to the role of rGO,which can act as the electron sink and transporter for separating photo-generated electron–hole pairs through interfacial charge transfer.Furthermore,rGO could adsorb formaldehyde molecules from air to produce a high concentration of formaldehyde on the surface of rGO/TiO_2.Under visible light irradiation for 240 min,the concentration of formaldehyde could be reduced to 58.5 ppbV.rGO/TiO_2 showed excellent moisture-resistance behavior,and after five cycles,r GO/TiO_2 maintained high photocatalytic activity for the removal of formaldehyde(84.6%).This work suggests that the synthesized rGO/TiO_2 is a promising photocatalyst for indoor formaldehyde removal.     

CeO2形貌结构对催化湿式空气氧化苯酚性能的影响

采用水热法、沉淀法和溶胶凝胶法制备了3种不同形貌的CeO₂催化材料,并将其用于湿式空气氧化苯酚水溶液过程中,探讨了CeO₂形貌结构对催化湿式氧化苯酚水溶液性能的影响.采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）、程序升温还原（TPR）等手段对CeO₂催化材料进行了表征.结果表明,水热法制备的CeO₂催化材料表现出较好催化性能,主要原因是水热法合成的CeO₂呈现交错的纳米棒状结构,主要暴露（220）晶面,且沿着（220）晶向生长.在反应温度为200℃、空气压力为2MPa、苯酚初始浓度500mg/L的条件下,最终（240min）COD的去除率为95.5%.     

CeO2形貌结构对催化湿式空气氧化苯酚性能的影响

采用水热法、沉淀法和溶胶凝胶法制备了3种不同形貌的CeO₂催化材料,并将其用于湿式空气氧化苯酚水溶液过程中,探讨了CeO₂形貌结构对催化湿式氧化苯酚水溶液性能的影响.采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）、程序升温还原（TPR）等手段对CeO₂催化材料进行了表征.结果表明,水热法制备的CeO₂催化材料表现出较好催化性能,主要原因是水热法合成的CeO₂呈现交错的纳米棒状结构,主要暴露（220）晶面,且沿着（220）晶向生长.在反应温度为200℃、空气压力为2MPa、苯酚初始浓度500mg/L的条件下,最终（240min）COD的去除率为95.5%.     

Au负载OMS-2催化剂的制备及其低温催化氧化性能

通过前掺杂法(QI),浸渍法(IM)和沉积-沉淀法(DP)3种方法制备了Au负载氧化锰八面体分子筛(OMS-2)Au/OMS-2催化剂,研究了制备方法和制备条件对其催化氧化CO活性的影响.采用X射线衍射(XRD)和BET比表面积测定等技术对所制样品进行表征.结果表明,沉积-沉淀法制备的Au/OMS-2-DP催化剂活性明显高于前掺杂法和浸渍法制备的催化剂,这与Au/OMS-2-DP催化剂比表面积较大和负载Au颗粒较小有关.制备条件(沉淀剂种类、制备溶液pH、Au负载量和催化剂焙烧温度)明显影响Au/OMS-2-DP催化剂的催化活性.对于各种不同的沉淀剂,以KOH为沉淀剂制备的催化剂活性最高,这可能与其无钝化作用,而且形成的Au颗粒较小有关;制备溶液的为最佳,当pH值过高或过低容易导致Au颗粒的聚集和Au沉淀量较少;XRD结果表明,当Au负载量为5wt%催化剂和催化剂焙烧为300℃时,所制备的催化剂颗粒最小,所得的催化剂活性最高.最佳条件制备的Au/OMS-2-DP催化剂活性较好,CO完全转化(100%)的温度为67℃.     

Treatment of phenol wastewater by microwave-induced ClO2-CuOx/Al2O3 catalytic oxidation process

The catalyst of CuOx/Al2O3 was prepared by the dipping-sedimentation method using γ-Al2O3 as a carrier. CuO and Cu2O were loaded on the surface of γ-Al2O3, characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). In the presence of CuOx/Al2O3, the microwave-induced chlorine dioxide (ClO2) catalytic oxidation process was conducted for the treatment of synthetic wastewater containing 100 mg/L phenol. The relationships between removal percentage and initial ClO2 concentration, catalyst dosage, microwave power, contact time, initial phenol concentration and pH were investigated and the results showed that microwave-induced ClO2-CuOx/Al2O3 process could effectively degrade contaminants in a short reaction time with a low oxidant dosage, extensive pH range. Under a given condition (ClO2 concentration 80 mg/L, microwave power 50 W, contact time 5 min, catalyst dosage 50 g/L, pH 9), phenol removal percentage approached 92.24%, corresponding to 79.13% of CODCr removal. The removal of phenol by microwave-induced ClO2-CuOx/Al2O3 catalytic oxidation process was a complicated non-homogeneous solid/water reaction, which fitted pseudo-first-order by kinetics. Compared with traditional ClO2 oxidation, ClO2 catalytic oxidation and microwave-induced ClO2 oxidation, microwave-induced ClO2 catalytic oxidation system could significantly enhance the degradation efficiency. It provides an effective technology for the removal of phenol wastewater.     

Pd/CeO2-Al2O3对烟气中多环芳烃的催化氧化性能研究

采用浸渍法制备了不同负载量及不同钯铈比(Pd:Ce)的Pd/CeO2-Al2O3催化剂,并结合XRD、BET、SEM、O2-TPD和H2-TPR等方法对催化剂的性质进行了表征,研究了所制备的催化剂对燃煤烟气中多环芳烃(PAHs)的催化转化效率.XRD和SEM结果表明,Ce和Pd在Al2O3表面呈高度分散状态,有利于PAHs的催化氧化.BET测试表明,Ce的引入改变了催化剂表面孔径结构,提高其比表面积.O2-TPD和H2-TPR测试表明,适当钯铈比条件下制备的催化剂有较强的储氧能力和活性.催化氧化实验结果表明,所制备的Pd/CeO2-Al2O3催化剂对PAHs具有较高的转化效率,其平均转化率均在80%以上,且PAHs的毒性当量显著降低,钯铈比对PAHs的催化氧化性能影响较大,当催化剂的钯铈比为1:1时,PAHs的转化率最高,可达90%以上.     

ZnMnxCo2-xO4活化过一硫酸盐降解有机污染物

分别以Zn（CH₃COO）₂·2H₂O、Mn（CH₃COO）₃·2H₂O和Co（CH₃COO）₂·4H₂O为锌源、锰源和钴源,采用溶胶-凝胶自燃烧法成功制备了ZnMn_xCo_2-xO₄（x=0~2）复合物,并用X射线衍射和X射线光电子能谱对其进行表征.同时,还研究了Mn/Co物质的量比、催化剂用量及PMS用量对目标污染物降解的影响.结果表明,该复合物可催化活化过一硫酸钾（PMS）降解有机污染物,当催化剂中x=0.8,催化剂投加量为0.2 g·L^-1,PMS用量为0.4 mmol·L^-1（0.25 g·L^-1）时,20 μmol·L^-1（10 mg·L^-1）罗丹明B（RhB）可在15 min内完全降解.ZnMn_0.8Co_1.2O₄的高催化活性主要归功于Mn³⁺和Co²⁺的协同效应.将ZnMn_xCo_2-xO₄-PMS体系用于亚甲基蓝、结晶紫、金橙、双酚A、4-氯酚等其他污染物的降解,也取得了较好的效果.基于电子自旋共振ESR和自由基猝灭实验的结果,可以推测该反应体系中活性物种为硫酸根自由基和羟基自由基.     

La-M-Co-O/堇青石催化剂的制备及催化氧化氯苯

采用柠檬酸络合法制备La-M-Co-O（M=Mn,Cr,Fe,Ni和Cu）/堇青石催化剂,运用BET,XRD,SEM,H₂-TPR和XPS技术对催化剂性能及微观结构进行表征分析,研究考察过渡金属掺杂,掺杂量以及焙烧温度等对催化剂催化氧化性能的影响.结果表明,随着催化剂焙烧温度升高至650℃时,催化剂表面所负载的活性氧化物颗粒最为分散,其氧化活性最佳,且当反应温度为350℃时,催化剂催化氧化氯苯转化率可达96.4%,究其原因是高温焙烧致使催化剂形成LaCoO₃钙钛矿型复合氧化物,其复合氧化物的晶体结构有利于催化剂催化氧化氯苯性能的提高.     

La-M-Co-O/堇青石催化剂的制备及催化氧化氯苯

采用柠檬酸络合法制备La-M-Co-O（M=Mn,Cr,Fe,Ni和Cu）/堇青石催化剂,运用BET,XRD,SEM,H₂-TPR和XPS技术对催化剂性能及微观结构进行表征分析,研究考察过渡金属掺杂,掺杂量以及焙烧温度等对催化剂催化氧化性能的影响.结果表明,随着催化剂焙烧温度升高至650℃时,催化剂表面所负载的活性氧化物颗粒最为分散,其氧化活性最佳,且当反应温度为350℃时,催化剂催化氧化氯苯转化率可达96.4%,究其原因是高温焙烧致使催化剂形成LaCoO₃钙钛矿型复合氧化物,其复合氧化物的晶体结构有利于催化剂催化氧化氯苯性能的提高.     

CeO2-ZrO2固溶体在催化湿式空气氧化苯酚废水中的作用

采用共沉淀法制备了CuO/ZnO/Ce O_2、CuO/ZnO/ZrO_2和CuO/ZnO/Ce O_2-Zr O_2催化湿式空气氧化苯酚废水催化剂,并采用N_2吸附-脱附、X射线衍射(XRD)、X射线光电子能谱(XPS)、程序升温还原(TPR)、N_2O滴定和电感耦合等离子体原子发射光谱等手段对催化剂进行了表征.结果表明,CuO/ZnO/Ce O_2-Zr O_2催化剂表现出最佳的催化性能.在200℃、2 MPa空气、苯酚初始浓度500 mg·L~(-1)的条件下,COD去除率为96.5%.XRD表明Ce O_2-Zr O_2复合氧化物载体以Ce_xZr_(1-x)O_2固溶体形式存在,增加了催化材料的储放氧能力.XPS表明Ce~(3+)和Ce~(4+)在催化剂表面共同存在,协调了氧化还原过程.TPR表明催化剂的还原性对催化剂的氧化活性起到至关重要的影响.由于CuO/ZnO/Ce O_2-Zr O_2催化剂活性组分和载体间的强相互作用,处理后的水样未发现金属离子,进而有效的提高了催化剂的稳定性和避免了对水样的二次污染.     

H2O和SO2对Cr-Ce/TiO2催化氧化NO性能的影响

采用浸渍法在最佳制备条件下制备了新型Cr-Ce/TiO2催化剂,并对催化剂进行了BET和XRD表征.同时,考察了反应温度、H2O和SO2对该催化剂催化氧化NO性能的影响,并对中毒催化剂进行了FT-IR分析,讨论了中毒机理.结果表明,Cr-Ce/TiO2催化剂具有良好的NO氧化活性,在空速为10000h-1、O2体积分数8%(φ)、NO进口体积分数700×10-6条件下,反应温度250℃时NO转化率可达到59.7%,330℃时NO转化率可达到最大值80.7%.单独加入10%(φ)H2O或300×10-6(φ)SO2都可使催化剂活性降低,但在较高温度时影响较小.330℃下单独通入SO2和同时通入H2O与SO210h后,由于催化剂表面生成了少量硫酸盐和亚硫酸盐,活性下降并维持在62.4%左右,能够满足对NOx进行高效吸收的要求;停止通入H2O和SO2后,催化剂活性恢复到71.6%,加热处理后活性能进一步恢复到78.5%.该催化剂具有比文献中报道的其它NO氧化催化剂更强的抗H2O和SO2毒化能力.     

Photodegradation of amoxicillin by catalyzed Fe3+/H2O2 process

Three oxidation processes of UV-Fe³⁺(EDTA)/H₂O₂ (UV: ultraviolet light; EDTA: ethylenediaminetetraacetic acid), UV-Fe³⁺/H₂O₂ and Fe³⁺/H₂O₂ were simultaneously investigated for the degradation of amoxicillin at pH 7.0. The results indicated that, 100% amoxicillin degradation and 81.9% chemical oxygen demand (COD_Cr) removal could be achieved in the UV-Fe³⁺ (EDTA)/H₂O₂ process. The treatment efficiency of amoxicillin and COD_Cr removal were found to decrease to 59.0% and 43.0% in the UV-Fe³⁺/H₂O₂ process; 39.6% and 31.3% in the Fe³⁺/H₂O₂ process. Moreover, the results of biodegradability (biological oxygen demand (BOD₅)/COD_Cr ratio) revealed that the UV-Fe³⁺ (EDTA)/H₂O₂ process was a promising strategy to degrade amoxicillin as the biodegradability of the effluent was improved to 0.45, compared with the cases of UV-Fe³⁺/H₂O₂ (0.25) and Fe³⁺/H₂O₂ (0.10) processes. Therefore, it could be deduced that EDTA and UV light performed synergetic catalytic effect on the Fe³⁺/H₂O₂ process, enhancing the treatment efficiency. The degradation mechanisms were also investigated via UV-Vis spectra, and high performance liquid chromatography-mass spectra. The degradation pathway of amoxicillin was further proposed.     

La1-xAlxFeO3催化剂降低甲醇/柴油二元燃料发动机非常规排放研究

采用喷雾热分解法制备了一系列钙钛矿型催化剂La_(1-x)Al_xFeO_3(x=0、0.3、0.5、0.7),采用X射线衍射仪和扫描电子显微镜,表征了La_(1-x)Al_xFeO_3相组成和微观形貌,评价了催化剂表面化学形态和催化活性指标.在发动机试验台架上,对甲醇/柴油发动机尾气中的甲醛、甲醇、1,3-丁二烯和N_2O进行了催化降解试验.结果表明:在La_(1-x)Al_xFeO_3中掺杂适宜量的Al有助于提高催化剂活性,改善催化剂比表面积和孔容积.当Al掺杂量为0.5时,所制备的La_(0.5)Al_(0.5)Fe O_3催化剂对甲醇、甲醛、丁二烯和N_2O的起燃温度(T50)分别为192、172、180和212℃,完全转化温度(T90)分别为227、205、240和324℃,呈现了良好的低温催化活性.对甲醇、甲醛、1,3-丁二烯和N_2O最大比排放分别为5.2×10~3、0.6×10~3、0.02和11.23 mg·k W~(-1)·h~(-1).与原发动机比排放相比,转化率达到了92%以上.表明La0.5Al0.5Fe O_3为适宜用于甲醇/柴油发动机尾气中非常规排放物低温催化降解的催化剂.     

Tix-Ni1-x-MOFs的制备及其CO选择性催化还原NOx研究

采用溶剂热法和微波法合成了不同比例的Ti_x-Ni_1-x-MOFs材料,并用于以CO为还原剂的选择性催化脱硝反应。结果表明,双金属Ti_x-Ni_1-x-MOFs的NO还原率显著高于单金属Ni-MOF,且反应温度窗口更宽,其中,Ti_0.2-Ni_0.8-MOF表现出最佳的脱硝效率,在200~400^oC温度范围达到100%的转化率。通过XRD,FT-IR,SEM,TGA,XPS,N₂吸脱附等表征手段发现,Ti掺杂Ni-MOF后有利于改善原子分散性,Ti、Ni间金属的相互作用有利于产生丰富的高效Ni-O-Ti位点,加强Ni²⁺+Ti⁴⁺↔Ni³⁺+Ti³⁺氧化还原循环,从而明显提高了NO+CO催化反应性能。与溶剂热法相比,微波法制备Ti_0.2-Ni_0.8-MOF具有合成效率高、结晶度好、晶粒细小均匀的优势,并进一步提高了其低温脱硝效果。