Innovative micro hole machining with minimum burr formation by the use of newly developed micro compound tool

The study focuses on the efforts for minimization of burr formation and improvement of hole surface roughness in micro through-hole machining. It deals with the development of micro compound tool which is consisting of a micro flat drill as the drilling part and a micro diamond-electroplated-grinding part for hole finishing. The finishing diameters of each drilling and grinding parts of the fabricated micro compound tool are 90 μm and 100 μm, respectively. The study focuses mainly on the effect of drill point angle and ultrasonic vibration applied during micro hole machining to the hole entrance and exit burrs formation. The used workpiece is made of stainless steel (SUS304) with a thickness of 100 μm. From the experiment, it was found that the tool having drill point angle of 118° resulted in a smaller burr formation although hole machining was conducted for 600 holes. Furthermore, the application of ultrasonic vibration during hole machining could improve the performance of the developed micro compound tool and decreased the burr size, especially the exit burr.     

Water jet guided laser as an alternative to EDM for micro-drilling of fuel injector nozzles: A comparison of machined surfaces

To characterize the inner surface of the fuel injector nozzle holes drilled by EDM and water jet guided laser drilling (Laser Micro-Jet) a specifically conceived scanning probe microscopy technique with true non-contact operating mode was used. A difference in morphology of the drilled surfaces is evident from the acquired surface topography along the hole axis for the two compared drilling techniques. Results showed that the surface texture can be characterized by (i) maximum peak-to-valley distance and (ii) periodicity. Acquired maps confirm that electro-eroded surfaces are an envelope of craters randomly distributed with total excursion up to 1.7 μm with a crater size of 15 μm. While, the efficient melt expulsion and immediate cooling of water jet guided laser generates a peak to valley distance of 800 nm with a periodicity of 18 μm. Average R_q derived from the measured cylindrical surfaces was 450 nm and 150 nm for EDM and Laser Micro-Jet, respectively. Water jet guided laser drilling has proved to be a reliable alternative to EDM from the point of view of repeatability of the results and surface quality to facilitate the atomization of the fuel jet.     

The precautionary principle and environmental persistence: prioritizing the decision-making process

There is continuing activity among regulatory bodies to assess and prioritize chemicals used in commerce based on their potential to be persistent, bioaccumulative, and toxic (PBT). Reliable data needed to perform a PBT hazard or risk assessment, however, may not always be readily available. Consequently concern may arise regarding the potential for false positives and false negatives to be wrongly classified. In order to more effectively classify substances, adequate time is needed to acquire the necessary data to support the overall PBT assessment. Of particular interest is the question of whether or not restrictions on the use and manufacture of a substance can be delayed to allow time to conduct the necessary field and laboratory studies of a particular substance? To address this question it is demonstrated that chemical partitioning property and environmental persistence information can be effectively combined to provide guidance for regulatory priority setting. Specifically, it is argued that substances that have media specific half-life values that exceed the regulatory threshold value for persistence under the EU chemicals REACH program, for example, are more likely to have a ‘legacy’ associated with their use when the log K_OA > 8, and when they are emitted to air or soil. Thus, precautionary actions limiting the use and manufacture of the substance may be warranted. Whereas substances emitted to air with log K_OA < 6 and log K_AW > ?2 are less likely to have a ‘legacy’ associated with their use. Thus precautionary actions in the absence of data may not be warranted.     

Changes in soil fertility parameters and the environmental effects in a rapidly developing region of China

An extensive knowledge of the temporal variability of soil fertility parameters and how this variation affects the environment is imperative to a wide range of disciplines within agricultural science for optimal crop production and ecosystem preservation. This paper examines the temporal variability of soil pH, organic matter (OM), cation exchange capacity (CEC), total nitrogen (TN), total phosphorus (TP), available phosphorus (P_Av), and available potassium (K_Av) on Cambosols (Entisols) (n = 179) and Anthrosols (Inceptisols) (n = 95) in Zhangjiagang County, China from 1980 to 2004. Nutrient input was monitored from 1983 to 2004. Annual N fertilizer rates were significantly different during three periods (1983–1989, 1989–1999, 1999–2004), where annual rates increased significantly after 1989 and then decreased after 1999. Annual P fertilizer rates were significantly different during two periods (1983–1993, 1993–2004) where annual rates increased after 1993. No change was found in K fertilizer rates. Soil pH marginally increased by 0.14 units in Cambosols, but significantly decreased by 1.02 units in Anthrosols. OM, CEC, and TN increased in both soil orders an average of 2.15 g kg^?1, 1.6 cmol kg^?1, and 0.21 g kg^?1, respectively. TP decreased in Anthrosols by 70 mg kg^?1, P_Av increased in Cambosols by 4.83 mg kg^?1, and K_Av decreased in Cambosols by 15 mg kg^?1. Fertilizer input rates are causing nutrient imbalances, contributing to acidification in Anthrosols, and decreasing C/N ratios. Nutrient loading of N and deficiency of K is also a potential problem in the area. Efforts should be made to readjust soil nutrient inputs to reach an optimal, sustainable level.     

Aero-lap polishing of poly crystalline diamond inserts using Multicon media

Increasing use of poly crystalline diamond (PCD) inserts as cutting tools and wear parts is vividly seen in automobile, aerospace, marine and precision engineering applications. The PCD inserts undergo series of manufacturing processes such as: grinding that forms the required shape and polishing that gives a fine finish. These operations are not straight forward as PCD is extremely resistant to grinding and polishing. Single crystal diamond can easily be polished by choosing a direction of easy abrasion, but polishing a PCD imposes serious difficulties as the grains are randomly oriented. Prior research on polishing of PCD inserts includes electro discharge grinding (EDG), dynamic friction polishing and grinding by a vitrified bonded diamond wheel. The surface textures of PCD produced using an EDG process often contains: micro cavities, particle pullout, micro-grooves, chipped edges, cracks and gouch marks. While applying the dynamic friction polishing method the PCD material undergoes phase transformation and hence increased polishing rate was apparently seen. However the phase transformation of PCD deteriorates the strength of the insert. Furthermore the inserts produced using the dynamic polishing method often exhibits cracks, chip off and edge damage while using as a cutting tool. Therefore, a new method “aero-lap polishing” was attempted as it applies controlled amount of impinging force by which the surface damage can be significantly reduced. The study did establish an improvement of surface finish of PCD from R_a = 0.55 μm, R_t = 4.5 μm to R_a = 0.29 μm, R_t = 1.6 μm within 15–25 min of polishing time along with significant reduction in surface defects.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

Effect of Silicon Powder Mixed EDM on Machining Rate of AISI D2 Die Steel

In this paper, the effect of silicon powder mixing into the dielectric fluid of EDM on machining characteristics of AISI D2 (a variant of high carbon high chrome) die steel has been studied. Six process parameters, namely peak current, pulse-on time, pulse-off time, concentration of powder, gain, and nozzle flushing have been considered. The process performance is measured in terms of machining rate (MR). The research outcome will identify the important parameters and their effect on MR of AISI D2 in the presence of suspended silicon powder in a kerosene dielectric of EDM. The study indicated that all the selected parameters except nozzle flushing have a significant effect on the mean and variation in MR (S/N ratio). Optimization to maximize MR has also been undertaken using the Taguchi method. The ANOVA analysis indicates that the percentage contribution of peak current and powder concentration toward MR is maximum among all the parameters. The confirmation runs showed that the setting of peak current at a high level (16 A), pulse-on time at a medium level (100 μs), pulse-off time at a low level (15 μs), powder concentration at a high level (4 g/l), and gain at a low level (0.83 mm/s) produced optimum MR from AISI D2 surfaces when machined by silicon powder mixed EDM.     

Changes in soil respiration across a chronosequence of tallgrass prairie reconstructions

Close relationships among climatic factors and soil respiration (R_s) are commonly reported. However, variation in R_s across the landscape is compounded by site-specific differences that impede the development of spatially explicit models. Among factors that influence R_s, the effect of ecosystem age is poorly documented. We hypothesized that R_s increases with grassland age and tested this hypothesis in a chronosequence of tallgrass prairie reconstructions in central Iowa, U.S.A. We also assessed changes in root biomass, root ingrowth, aboveground net primary productivity (ANPP), and the strength of soil temperature and moisture in predicting R_s. We found a significant increase in total growing season R_s with prairie age (R² = 0.79), ranging from 714 g C m^?2 in the youngest reconstruction (age 4) to 939 g C m^?2 in the oldest prairie (age 12). Soil temperature was a strong predictor of intra-seasonal R_s among prairies (R² = 0.78–0.87) but mean growing season soil temperature and moisture did not relate to total R_s. The increase in R_s with age was positively correlated with root biomass (r = 0.80) and ANPP (r = 0.87) but not with root ingrowth. Our findings suggest that growing season R_s increases with tallgrass prairie age, root biomass, and ANPP during young grassland development.     

Ammonia and nitrous oxide emissions following land application of high and low nitrogen pig manures to winter wheat at three growth stages

Nitrous oxide (N₂O) and ammonia (NH₃) emissions from surface applied high (HN) and low (LN) nitrogen pig manures were measured under field conditions. Manures were band-spread to a winter wheat crop at three growth stages—mid-tillering, stem elongation and flag leaf emergence. The N₂O flux rates were measured using the static chamber technique while NH₃ volatilisation was assessed using a micrometeorological mass balance technique with passive flux samplers. The N₂O emissions were episodic in nature with flux rates observed ranging from 2.8 to 31.5 g N₂O–N ha^?1 day^?1 (P < 0.001). Higher N₂O emissions generally occurred after rainfall events. Highest N₂O losses were observed from the HN treatment with LN manure use decreasing emissions by 18% (P < 0.03). The NH₃ volatilisation rates were highest within 1 h of manure application with 95% of emissions occurring within 24 h (P < 0.001). Cumulative N loss was highest at mid-tillering as low crop canopy cover and increased wind-speeds enhanced NH₃ loss (P < 0.001). Highest emissions were measured from the HN manure (P < 0.03). Total ammoniacal N loss ranged from 6 to 11%. Crop N uptake and grain yield were unaffected by application timing or manure type. Therefore, the use of LN manures decreased gaseous emissions of N₂O and NH₃ without any adverse effects on crop performance.     

Emissions of N2O and NH3, and nitrogen leaching from direct seeded rice under different tillage practices in central China

Tillage practices affect the fate of fertilizer nitrogen (N) through influencing transformations of N, but few studies have examined N₂O and NH₃ emissions, and N leaching from different rice tillage systems. Thus the objective of this study was to assess N₂O emission, NH₃ volatilization and N leaching from direct seeded rice in conventional tillage (CT) and no-tillage (NT) production systems in the subtropical region of China during the 2008 and 2009 rice growing seasons. Treatments were established following a split-plot design of a randomized complete block with tillage practices as the main plot and N fertilizer level as the sub-plot treatment, and there were four treatments: NT + no fertilizer (NT0), CT + no fertilizer (CT0), NT + compound fertilizer (NTC) and CT + compound fertilizer (CTC), respectively. Results showed that N fertilization significantly increased (p < 0.01) N₂O emissions, NH₃ volatilization and N leaching from rice fields in both years. In general, there was no significant difference in N₂O emissions and NH₃ volatilization between NT0 and CT0 in both years, while NTC had significantly higher (p < 0.05) N₂O emissions and NH₃ volatilization compared to CTC. Over the two rice growing seasons, NTC showed 32% and 47% higher N₂O emissions, and 29% and 52% higher NH₃ losses than CTC. Higher (p < 0.05) N₂O emissions from NTC than CTC were presumably due to higher soil organic C and greater denitrification. Total N and NO₃^? concentrations were higher (p < 0.05) in CTC than NTC, but larger volumes of percolation water in NTC than CTC resulted in no significant difference in leakage of total N and NO₃^?. Hence, application of N fertilizer in combination with NT appeared to be ineffective in reducing N losses from N fertilizer in paddy fields.     

Study of specific energy and friction coefficient in minimum quantity lubrication grinding using oil-based nanolubricants

An investigation on minimum quantity lubrication (MQL) grinding was carried out with the scope of documenting the process efficiency of oil-based nanolubricants. The nanolubricants were composed of MoS₂ nanoparticles (<100 nm) over coated with organic agents, dispersed in two different base oils—mineral oil (paraffin) and vegetable oil (soybean). Surface grinding tests were carried out on cast iron and EN 24 steel under different lubrication conditions—MQL using nanolubricants (varying compositional chemistry and concentration of nanoparticles), pure base oils (without nanoparticles) and base oils containing MoS₂ microparticles (3–5 μm), and flood grinding using water-based coolant. Specific energy, friction coefficient in grinding and G-ratio were used as measurands for determining the process efficiency. Results show that MQL grinding with nanolubricants increases the process efficiency by reducing energy consumption, frictional losses at the wheel–workpiece interface and tool wear. The process efficiency is also found to increase with increasing nanoparticle concentration. Soybean and paraffin based-nanolubricant performed best for steel and cast iron, respectively, showing a possible functional relationship between the compositional chemistry of nanolubricant and the workpiece material, which will be the goal of future work.     

The influence of long term trends in pollutant emissions on deposition of sulphur and nitrogen and exceedance of critical loads in the United Kingdom

In the United Kingdom, as with other European countries, land-based emissions of NO_x and SO₂ have fallen significantly over the last few decades. SO₂ emissions fell from a peak of 3185 Gg S in 1970 to 344 Gg S in 2005 and are forecast by business-as-usual emissions scenarios to fall to 172 Gg by 2020. NO_x emissions were at a maximum of 951 Gg N in 1970 and fell to 378 by 2005 with a further decrease to 243 Gg N forecast by 2020. These large changes in emissions have not been matched by emissions changes for NH₃ which decreased from 315 Gg N in 1990 to 259 in 2005 and are forecast to fall to 222 by 2020. The Fine Resolution Atmospheric Multi-pollutant Exchange model (FRAME) has been applied to model the spatial distribution of sulphur and nitrogen deposition over the United Kingdom during a 15-year time period (1990–2005) and compared with measured deposition of sulphate, nitrate and ammonium from the national monitoring network. Wet deposition of nitrogen and sulphur was found to decrease more slowly than the emissions reductions rate. This is attributed to a number of factors including increases in emissions from international shipping and changing rates of atmospheric oxidation. The modelled time series was extended to a 50-year period from 1970 to 2020. The modelled deposition of SO_x, NO_y and NH_x to the UK was found to fall by 87%, 52% and 25% during this period. The percentage area of sensitive habitats in the United Kingdom for which critical loads are exceeded is estimated to fall from 85% in 1970 to 37% in 2020 for acidic deposition and from 73% to 49% for nutrient nitrogen deposition. The significant reduction in land emissions of SO₂ and NO_x focuses further attention in controlling emissions from international shipping. Future policies to control emissions of ammonia from agriculture will be required to effect further significant reductions in nitrogen deposition.     

Life-cycle environmental and economic impacts of energy-crop fuel-chains: an integrated assessment of potential GHG avoidance in Ireland

This paper combines life-cycle analyses and economic analyses for Miscanthus and willow heat and electricity fuel-chains in Ireland. Displaced agricultural land-uses and conventional fuels were considered in fuel-chain permutations. Avoided greenhouse gas (GHG) emissions ranged from 7.7 to 35.2 t CO₂ eq. ha⁻¹ a⁻¹. Most fuel-chain permutations exhibited positive discounted financial returns, despite losses for particular entities at a farm-gate processed-biomass price of €100 t⁻¹ dry-matter. Attributing a value of €10 t⁻¹ CO₂ eq. to avoided GHG emissions, but subtracting financial returns associated with displaced fuel supplies, resulted in discounted annual national economic benefits (DANEBs) ranging from −457 to 1887€ ha⁻¹ a⁻¹. Extrapolating a plausible combination of fuel-chains up to a national indicative scenario resulted in GHG emission avoidance of 3.56 Mt CO₂ eq. a⁻¹ (5.2% of national emissions), a DANEB of 167 M€, and required 4.6% of national agricultural land area. As cost-effective national GHG avoidance options, Miscanthus and willow fuel-chains are robust to variation in yields and CO₂ price, and appear to represent an efficient land-use option (e.g. compared with liquid biofuel production). Policies promoting utilisation of these energy-crops could avoid unnecessary, and environmentally questionable, future purchase of carbon credits, as currently required for national Kyoto compliance.     

Disaggregated greenhouse gas emission inventories from agriculture via a coupled economic-ecosystem model

Estimates of regional greenhouse gas emissions from agricultural systems are needed to evaluate possible mitigation strategies with respect to environmental effectiveness and economic feasibility. Therefore, in this study, we used the GIS-coupled economic-ecosystem model EFEM–DNDC to assess disaggregated regional greenhouse gas (GHG) emissions from typical livestock and crop production systems in the federal state of Baden-Württemberg, Southwest Germany. EFEM is an economic farm production model based on linear programming of typical agricultural production systems and simulates all relevant farm management processes and GHG emissions. DNDC is a process-oriented ecosystem model that describes the complete biogeochemical C and N cycle of agricultural soils, including all trace gases.Direct soil emissions were mainly related to N₂O, whereas CH₄ uptake had marginal influence (net soil C uptake or release was not considered). The simulated N₂O emissions appeared to be highly correlated to N fertilizer application (R² = 0.79). The emission factor for Baden-Württemberg was 0.97% of the applied N after excluding background emissions.Analysis of the production systems showed that total GHG emissions from crop based production systems were considerably lower (2.6–3.4 Mg CO₂ eq ha⁻¹) than from livestock based systems (5.2–5.3 Mg CO₂ eq ha⁻¹). Average production system GHG emissions for Baden-Württemberg were 4.5 Mg CO₂ eq ha⁻¹. Of the total 38% were derived from N₂O (direct and indirect soil emissions, and manure storage), 40% were from CH₄ (enteric fermentation and manure storage), and 22% were from CO₂ (mainly fertilizer production, gasoline, heating, and additional feed). The stocking rate was highly correlated (R² = 0.85) to the total production system GHG emissions and appears to be a useful indicator of regional emission levels.     

Investigation on mechanism of phosphate removal on carbonized sludge adsorbent

For the removal of phosphate (PO₄^3 -) from water, an adsorbent was prepared via carbonization of sewage sludge from a wastewater treatment plant: carbonized sludge adsorbent (CSA). The mechanism of phosphate removal was determined after studying the structure and chemical properties of the CSA and its influence on phosphate removal. The results demonstrate that phosphate adsorption by the CSA can be fitted with the pseudo second-order kinetics and Langmuir isotherm models, indicating that the adsorption is single molecular layer adsorption dominated by chemical reaction. The active sites binding phosphate on the surface are composed of mineral particles containing Si/Ca/Al/Fe. The mineral containing Ca, calcite, is the main factor responsible for phosphate removal. The phosphate removal mechanism is a complex process including crystallization via the interaction between Ca^2 + and PO₄^3 -; formation of precipitates of Ca^2 +, Al^3 +, and PO₄^3 -; and adsorption of PO₄^3 - on some recalcitrant oxides composed of Si/Al/Fe.     

Effects of different diets on utilization of nitrogen from cattle slurry applied to grassland on a sandy soil in The Netherlands

Dietary adjustments have been suggested as a means to reduce N losses from dairy systems. Differences in fertilizing value of dairy slurry as a result of dietary adjustments were evaluated in a 1-year grassland experiment and by long-term modelling. Slurry composition of non-lactating dairy cows was manipulated by feeding diets with extreme high and low levels of dietary protein and energy. C:N_total ratio of the produced slurries ranged from 5.1 to 11.4. To evaluate their short-term fertilizer N value, the experimental slurries (n = 8) and slurries from commercial farms with variable composition (n = 4), were slit-injected in two grassland fields on the same sandy soil series in the north of The Netherlands (53°10′N, 6°04′E), with differences in sward age and ground water level. The recently established grassland field (NEW) was characterized by lower soil OM, N and moisture contents, less herbs and more modern grass varieties compared to the older grassland field (OLD). Slurry was applied in spring (100 kg N ha⁻¹) and after the first cut (80 kg N ha⁻¹) while in total four cuts were harvested. Artificial fertilizer N treatments were included in the experiment to calculate the mineral fertilizer equivalent (MFE) of slurry N. The OLD field showed a higher total N uptake whereas DM yields were similar for the two fields. Average MFE of the slurries on the OLD field (47%) was lower than on the NEW field (56%), probably as a result of denitrification of slurry N during wet conditions in spring. Slurries from high crude protein diets showed a significantly higher MFE (P < 0.05) compared to low crude protein diets. No significant differences in MFE were observed between slurries from high and low energy diets. On both fields, MFE appeared to be positively related to the ammonium content (P < 0.001) and negatively to the C:N_total ratio of the slurry DM (P = 0.001). Simulation of the effect of long-term annual application of 180 kg N ha⁻¹ with highest and lowest C:N_total ratio suggested that both slurries would lead to an increase in annual soil N mineralization. Both soil N mineralization and SOC appeared to be substantially higher in equilibrium state for the slurry with the highest C:N_total ratio. It is concluded that in a situation with slit-injection, the reduced first-year N availability of slurry with a high C:N_total ratio as observed in the grassland experiment will only be compensated for by soil N mineralization on the very long term.     

Biogas production from maize and dairy cattle manure—Influence of biomass composition on the methane yield

There is an increasing world wide demand for energy crops and animal manures for biogas production. To meet these demands, this research project aimed at optimising anaerobic digestion of maize and dairy cattle manures. Methane production was measured for 60 days in 1 l eudiometer batch digesters at 38 °C. Manure received from dairy cows with medium milk yield that were fed a well balanced diet produced the highest specific methane yield of 166.3 Nl CH₄ kg VS⁻¹. Thirteen early to late ripening maize varieties were grown on several locations in Austria. Late ripening varieties produced more biomass than medium or early ripening varieties. On fertile locations in Austria more than 30 Mg VS ha⁻¹ can be produced. The methane yield declined as the crop approaches full ripeness. With late ripening maize varieties, yields ranged between 312 and 365 Nl CH₄ kg VS⁻¹ (milk ripeness) and 268–286 Nl CH₄ kg VS⁻¹ (full ripeness). Silaging increased the methane yield by about 25% compared to green, non-conserved maize. Maize (Zea mays L.) is optimally harvested, when the product from specific methane yield and VS yield per hectare reaches a maximum. With early to medium ripening varieties (FAO 240–390), the optimum harvesting time is at the “end of wax ripeness”. Late ripening varieties (FAO ca. 600) may be harvested later, towards “full ripeness”. Maximum methane yield per hectare from late ripening maize varieties ranged between 7100 and 9000 Nm³ CH₄ ha⁻¹. Early and medium ripening varieties yielded 5300–8500 Nm³ CH₄ ha⁻¹ when grown in favourable regions. The highest methane yield per hectare was achieved from digestion of whole maize crops. Digestion of corns only or of corn cob mix resulted in a reduction in methane yield per hectare of 70 and 43%, respectively. From the digestion experiments a multiple linear regression equation, the Methane Energy Value Model, was derived that estimates methane production from the composition of maize. It is a helpful tool to optimise biogas production from energy crops. The Methane Energy Value Model requires further validation and refinement.     

Methane,nitrous oxide and ammonia emissions during storage and after application of dairy cattle slurry and influence of slurry treatment

Slurries are a significant source of CH₄, NH₃ and N₂O emissions to the atmosphere. The research project aimed at quantifying CH₄, NH₃ and N₂O emissions from liquid manure stores and after manure application under field conditions. The influence of the manure treatment options “no treatment”, “slurry separation”, “anaerobic digestion”, “slurry aeration” and “straw cover” on the emission level was investigated. Approximately 10 m³ of differently treated slurry were stored in pilot scale slurry tanks. Emissions were followed for c. 80 days. After the storage period, slurries were applied to permanent grassland. Greenhouse gas emissions from slurry were mainly caused by methane emissions during storage and by nitrous oxide emissions after field application of manures. Mitigation of GHG emissions can be achieved by a reduction in slurry dry matter and easily degradable organic matter content. Ammonia emissions mainly occurred after field application. Untreated slurry emitted 226.8 g NH₃ m⁻³ and 92.4 kg CO₂ eq. m⁻³ (storage and field application). Slurry separation (liquid fraction and composting of the solid fraction) resulted in NH₃ losses of 402.9 g m⁻³ and GHG losses of 58.5 kg CO₂ eq. m⁻³. Anaerobic digestion was a very effective means to reduce GHG emissions. 37.9 kg CO₂ eq. m⁻³ were lost. NH₃ emissions were similar to those from untreated slurry. Covering the slurry store with a layer of chopped straw instead of a wooden cover increased NH₃ emissions to 320.4 g m⁻³ and GHG emissions to 119.7 kg CO₂ eq. m⁻³. Slurry aeration nearly doubled NH₃ emissions compared to untreated slurry. GHG emissions were reduced to 53.3 kg CO₂ eq. m⁻³.     

Lodging in rice can be alleviated by atmospheric CO2 enrichment

The projected increase of atmospheric CO₂ concentration [CO₂] is expected to increase yield of agricultural C₃ crops, but little is known about effects of [CO₂] on lodging that can reduce yield. This study examined the interaction between [CO₂] and nitrogen (N) fertilization on the lodging of rice (Oryza sativa L.) using free-air CO₂ enrichment (FACE) systems installed in paddy fields at Shizukuishi, Iwate, Japan (39°38′N, 140°57′E). Rice plants were grown under two levels of [CO₂] (ambient = 365 μmol mol⁻¹; elevated [CO₂] = 548 μmol mol⁻¹) and three N fertilization regimes: a single initial basal application of controlled-release urea (8 g N m⁻², CRN), split fertilization with a standard amount of ammonium sulfate (9 g N m⁻², MN), and ample N (15 g N m⁻², HN). Lodging score (six ranks at 18° intervals, with larger scores indicating greater bending), yield, and yield components were measured at maturity. The lodging score was significantly higher under HN than under CRN and MN, but lodging was alleviated by elevated [CO₂] under HN. This alleviation was associated with the shortened and thickened lower internodes, but was not associated with a change in the plant's mass moment around the culm base. A positively significant correlation between lodging score and ripening percentage indicated that ripening percentage decreased by 4.5% per one-unit increase in lodging score. These findings will be useful to develop functional algorithm that can be incorporated into mechanistic crop models to predict rice production more accurately in a changing climate and with different cultural practices.     

Effects of irrigation,fertilization and crop straw management on nitrous oxide and nitric oxide emissions from a wheat–maize rotation field in northern China

One-year winter wheat–summer maize rotation is the most popular double cropping system in north-central China, and this highly productive system is an important source of nitrous oxide (N₂O) and nitric oxide (NO) emissions due to the high fertilizer N and irrigation water inputs. To sustain the high crop production and mitigate the detrimental impacts of N₂O and NO emissions, improved management practices are extensively applied. The aim of this study is therefore to evaluate the effects of an improved management practice of irrigation, fertilization and crop straw on grain yield and N₂O and NO emissions for a wheat–maize rotation field in northern China. Using automated and manual chamber measuring systems, we monitored N₂O and NO fluxes for the conventional (CT, 2007–2008), improved (IT, 2007–2008), straw-amended (WS, 2008–2009), straw-not-amended (NS, 2008–2009), and no N-fertilizer treatments (WS–NN, 2008–2009), respectively, for one rotation-year. The grain yields were determined for CT and IT for three rotation-years (2005–2008) and for WS, NS and WS–NN for one rotation-year (2008–2009). The improved management of irrigation and fertilization reduced the annual N fertilization rate and irrigation amount by 17% and 30%, respectively; increased the maize yield by 7–14%; and significantly decreased the N₂O and NO emissions by 7% (p < 0.05) and 29% (p < 0.01), respectively. The incorporation of wheat straw increased the cumulative N₂O and NO emissions in the following maize season by 58% (p < 0.01) and 13%, respectively, whereas the effects of maize straw application were not remarkable. The N₂O and NO emission factors of applied N were 2.32 ± 2.32% and 0.42 ± 1.69% for wheat straw and 0.67 ± 0.23% and 0.54 ± 0.15% for chemical N-fertilizers, respectively. Compared to conventional management practices using high application rates of irrigation water and chemical N-fertilizer as well as the field burning of crop straw, the improved management strategy presented here has obvious environmentally positive effects on grain yield and mitigation of N₂O and NO emissions.