Prediction of vortex height from mechanical mixing in metal matrix nanocomposite processing by means of dimensional analysis and scaling

Mechanical mixing can be used for initial dispersion and distribution of nanoparticle agglomerates in metal matrix nanocomposite (MMNC) fabrication. As vortex height increases, flow is enhanced as well as the risk of oxidate melt contamination. The goal of this study was to examine and predict vortex height using dimensional analysis while varying fluid and the angular speed of a pitched square-blade impeller. An equation proposed by Markopoulos et al. was verified for the present experimental conditions. The relevant dimensionless numbers were the Reynolds (Re), Froude (Fr) and Galilei (Ga) numbers. A modified Fr was defined (Fr*) including the shaft and blade angles of the impeller. Experiments allowed calculation of the dimensionless numbers. Two fluids, water and 50 vol% aqueous glycerine, were used. Angular clockwise speed varied from 200 to 900 rpm in 100 rpm increments. Vortex height was measured in lateral view digital images. Correlations of the dimensionless numbers yielded, first, a linear relationship of the product of dimensionless vortex height (H) and specific gravity (ρ*) with respect to Fr*. A polynomial relationship was found between H and ReFr* for each fluid. The polynomial coefficients, in turn, follow a power law behavior with respect to Ga. This allows a prediction of vortex height in other Newtonian fluids that satisfy the single-phase isothermal flow condition. Perhaps, molten aluminum used in MMNC fabrication, can be analyzed based on a simple, room temperature, low cost transparent fluid system. For the experimental conditions in this study, the equation proposed by Markopoulos et al. was valid. The predicting methodology was verified with experimental results using 25 vol% aqueous glycerine, resulting in an absolute percent error of 5.29%, comparable and lower than an error of 9.12% obtained by predicting vortex height with Markopoulos’ equation.     

A promising clean process for production of diosgenin from Dioscorea zingiberensis C. H. Wright

This study proposes a new approach for diosgenin production from Dioscorea zingiberensis C. H. Wright tubers with respect to resources utilization and clean production. This process consisted of two successive parts, i.e., recovery of starch from raw material, and microbial hydrolysis of the residue to produce diosgenin by Trichoderma reesei. In the first step, about 75.4% of hemicellulose and 98.0% of starch were removed from the tubers. In the second step, about 90.2% of diosgenin was released from saponins by T. reesei at 30 °C, at an aeration of 0.80 vvm and agitation rate of 300 rpm in a 5.0 L bioreactor. Significant reduction of pollutant production was detected by replacing the traditional approach with the proposed new method. About 99.2% of reducing sugar, 99.4% of chemical oxygen demand, 99.2% of total organic carbon, 100% of SO₄^2?, and 100% of acid was reduced in the new processing wastewater.     

CaCO3 production using liquid waste from Solvay method

Process of obtaining CaCO₃ from the waste post-distillation liquid DS and post-filtration liquid from Solvay method of the soda production at 303 K was investigated. Reagents were dosed in a stoichiometric ratio without dilution, for different concentrations of the DS and post-filtration liquids. The dosage time was varied in the range 2–30 min, the reagent stirring rate was 500 rpm. For the obtained samples of CaCO₃, the bulk and packing densities, water, paraffin oil and dibutyl phthalate absorption capacities, distribution of the particle size as well as the crystalline form were determined.     

Analysis of temperature effects on seasonal and interannual variation in CH4 emission from rice-planted pots

Rice (Oryza sativa L.) paddies are one of the major sources of atmospheric methane (CH₄), a greenhouse gas. To elucidate the quantitative relationship between CH₄ emission from rice paddies and temperature, 6 years data of CH₄ emission from pot experiments were analyzed in terms of the sum of effective temperature (∑(T−15); T is the daily mean air temperature (°C)). The base temperature of 15 °C was adopted as the 0 °C physiological temperature for methanogens. Significant positive correlations between total CH₄ emission throughout the rice growth period and ∑(T−15) were observed for pots with rice straw (RS) application at a rate of 6 g kg⁻¹ soil, which corresponds to 6 t ha⁻¹ (r=0.830⁷¹), and those without RS application (r=0.818⁷¹). It was confirmed that temperature is a major factor affecting the interannual variation in CH₄ emission. For the 1993 and 1995 data sets that include seven and four levels of RS application, the relationship between seasonal CH₄ emission and RS application rate could be expressed using linear functions (r=0.988⁷¹, 0.996⁷¹), the slopes of which were similar to each other. Based on these findings, we confirmed that the dependence of seasonal CH₄ emission on both temperature and RS application rate can be described by a single linear equation.     

Using supercritical carbon dioxide as solvent to replace water in polyethylene terephthalate (PET) fabric dyeing procedures

Dyeing fabrics in supercritical carbon dioxide (SCD) instead of water can save energy, reduce water use and prevent pollution. The special pilot plant was designed to test dyeing procedures in supercritical carbon dioxide and the analyses of the results indicate major benefits as compared to water based procedures. The dyeing of polyethylene terephthalate (PET) fabric in supercritical carbon dioxide using special pilot plant was investigated. Disperse dye, C.I. (color index) Disperse Blue 79, was used in this study. After dyeing, rinsing in supercritical carbon dioxide, which removes the excess dyes, was also discussed. At the same dyeing conditions, K/S (color yield) of dyed fabric significantly increased with increasing the dye concentration from 1% o.w.f. (on weight of fabric) to 5% o.w.f. Dyeing temperature and pressure had a strong influence on the color yield. When the temperature rose above 110 °C, the increase in color yield was obvious. At 20 MPa, 120–130 °C, dyeing reached equilibrium after 60 min. The excess dye of the dyed PET fabric was small. The suitable condition in supercritical carbon dioxide for removal of excess dye from the dyed fabric was 70 °C, 20 MPa. The PET fabric dyed in supercritical carbon dioxide had good fastness and physical properties.     

Lodging in rice can be alleviated by atmospheric CO2 enrichment

The projected increase of atmospheric CO₂ concentration [CO₂] is expected to increase yield of agricultural C₃ crops, but little is known about effects of [CO₂] on lodging that can reduce yield. This study examined the interaction between [CO₂] and nitrogen (N) fertilization on the lodging of rice (Oryza sativa L.) using free-air CO₂ enrichment (FACE) systems installed in paddy fields at Shizukuishi, Iwate, Japan (39°38′N, 140°57′E). Rice plants were grown under two levels of [CO₂] (ambient = 365 μmol mol⁻¹; elevated [CO₂] = 548 μmol mol⁻¹) and three N fertilization regimes: a single initial basal application of controlled-release urea (8 g N m⁻², CRN), split fertilization with a standard amount of ammonium sulfate (9 g N m⁻², MN), and ample N (15 g N m⁻², HN). Lodging score (six ranks at 18° intervals, with larger scores indicating greater bending), yield, and yield components were measured at maturity. The lodging score was significantly higher under HN than under CRN and MN, but lodging was alleviated by elevated [CO₂] under HN. This alleviation was associated with the shortened and thickened lower internodes, but was not associated with a change in the plant's mass moment around the culm base. A positively significant correlation between lodging score and ripening percentage indicated that ripening percentage decreased by 4.5% per one-unit increase in lodging score. These findings will be useful to develop functional algorithm that can be incorporated into mechanistic crop models to predict rice production more accurately in a changing climate and with different cultural practices.     

Model-Based Design of Motorized Spindle Systems to Improve Dynamic Performance at High Speeds

High-speed motorized spindle systems are subjected to several effects during high-speed rotations that can cause substantial changes in their dynamic and thermal behaviors, leading to chatter, bearing thermal seizure, or premature spindle bearing failures. Therefore, it is important to consider these high-speed effects in the design stage of high-speed motorized spindles. This paper first develops a design flow chart to represent the overall spindle design problems. Based on this flow chart, eight design parameters are identified. A design sensitivity analysis of these eight design parameters is then conducted based on an integrated finite element method model to investigate their influence on the natural frequencies of the spindle system. Based on the rule of Maximum Improvement First, a set of systematic design procedures is proposed to suggest design changes to a custom-designed motorized spindle rated at 32 kW and 25,000 rpm. Based on the simulation results, it is shown that the first-mode frequency of this spindle system can be improved from 790.7 Hz to 934 Hz at 25,000 rpm by simply adjusting the front and rear bearing locations. At the optimal design, the first-mode frequency can reach 1454.3 Hz at 25,000 rpm, which represents more than 80 percent improvement over the original design.     

Effects of different diets on utilization of nitrogen from cattle slurry applied to grassland on a sandy soil in The Netherlands

Dietary adjustments have been suggested as a means to reduce N losses from dairy systems. Differences in fertilizing value of dairy slurry as a result of dietary adjustments were evaluated in a 1-year grassland experiment and by long-term modelling. Slurry composition of non-lactating dairy cows was manipulated by feeding diets with extreme high and low levels of dietary protein and energy. C:N_total ratio of the produced slurries ranged from 5.1 to 11.4. To evaluate their short-term fertilizer N value, the experimental slurries (n = 8) and slurries from commercial farms with variable composition (n = 4), were slit-injected in two grassland fields on the same sandy soil series in the north of The Netherlands (53°10′N, 6°04′E), with differences in sward age and ground water level. The recently established grassland field (NEW) was characterized by lower soil OM, N and moisture contents, less herbs and more modern grass varieties compared to the older grassland field (OLD). Slurry was applied in spring (100 kg N ha⁻¹) and after the first cut (80 kg N ha⁻¹) while in total four cuts were harvested. Artificial fertilizer N treatments were included in the experiment to calculate the mineral fertilizer equivalent (MFE) of slurry N. The OLD field showed a higher total N uptake whereas DM yields were similar for the two fields. Average MFE of the slurries on the OLD field (47%) was lower than on the NEW field (56%), probably as a result of denitrification of slurry N during wet conditions in spring. Slurries from high crude protein diets showed a significantly higher MFE (P < 0.05) compared to low crude protein diets. No significant differences in MFE were observed between slurries from high and low energy diets. On both fields, MFE appeared to be positively related to the ammonium content (P < 0.001) and negatively to the C:N_total ratio of the slurry DM (P = 0.001). Simulation of the effect of long-term annual application of 180 kg N ha⁻¹ with highest and lowest C:N_total ratio suggested that both slurries would lead to an increase in annual soil N mineralization. Both soil N mineralization and SOC appeared to be substantially higher in equilibrium state for the slurry with the highest C:N_total ratio. It is concluded that in a situation with slit-injection, the reduced first-year N availability of slurry with a high C:N_total ratio as observed in the grassland experiment will only be compensated for by soil N mineralization on the very long term.     

Irrigation of olive groves in Southern Italy with treated municipal wastewater: Effects on microbiological quality of soil and fruits

The use of municipal wastewater in agriculture requires a careful monitoring of a range of hygiene parameters. Yearly hygienic impact assessments on soil and fruit were made between 2000 and 2006 in an olive (Olea europaea L.) grove established near a municipal wastewater treatment plant in Southern Italy (Ferrandina–Basilicata region, 40°29′ N, 16°28′ E). The experimental grove was managed in two plots. The first plot, non-tilled, was drip irrigated daily with reclaimed wastewater. The second plot was unirrigated (i.e. rainfed) and subject to conventional management for the region. Samples of wetted soil from different depths and of treated wastewater were analysed for Escherichia coli, enterococci, sulphite-reducing Clostridium spores and Salmonella spp. Fruits were collected both from the canopy and from nets spread on the ground and analysed for faecal contamination. The average annual quantity of wastewater distributed was 293 mm. E. coli concentration in the wastewater varied considerably, being frequently above the stringent Italian mandatory limit of 10 CFU 100 mL^?1 and also the WHO limit of 1000 MPN 100 mL^?1. Salmonella was never detected in the wastewater, the soil or on the fruit samples. Slight increases in the other bacteria were observed in the wastewater-irrigated soil during the irrigation season and especially in the top 10 cm. Soil resilience and bacterial mortality/inactivation probably explains the seasonal decrease of soil bacteria content over the 7 years of the study. Because of their high resistance to disinfection treatments and to environmental conditions, the spores of the sulphite-reducing bacterium Clostridium could be useful as an indicator of contamination in future guidelines that might be enacted for the use of wastewater in agriculture. No significant microbial contamination was recorded on fruit harvested directly from the canopy of the wastewater-irrigated trees. Contaminations on fruits sampled from the ground in the wastewater-irrigated plot were always low and usually similar to, or lower than those observed on drupes collected from the rainfed plot. In the rainfed plot, the recorded occasional contaminations were probably due to a number of factors, such as grazing of farm stock, presence of wild animals and surface water runoff from adjacent agricultural areas. This work confirms that, under suitable conditions, low-quality wastewater can be useful as an additional water resource for olive irrigation in water-scarce Mediterranean environments.     

Performance and water-use efficiency (single-leaf vs. whole-canopy) of well-watered and half-stressed split-root Lambrusco grapevines grown in Po Valley (Italy)

‘Lambrusco a foglia frastagliata’ grapevines (Vitis vinifera L.) were grown outdoors at Piacenza (44°55′N, 9°44′E, Po Valley, Italy) with the root system split between two 30-L pots and subjected from pre-veraison (17 July) to harvest (5 September) to soil drying of half of the root system (HS) induced by withholding water from one of the two pots as compared to well-watered (WW) vines (both pots daily recharged at field capacity). Volumetric soil-water content, pre-dawn and mid-morning leaf water potential, single-leaf gas-exchange as assimilation rate, stomatal conductance and transpiration were monitored throughout the trial. Whole-canopy gas-exchange as net CO₂ exchange rate (NCER) and transpiration were tracked from 31 August to 7 September on three vines per treatment on a 24-h basis using an enclosure method. Primary leaf carbon isotope (δ¹³C) composition, yield components and must composition were determined at harvest.Withdrawing water from one pot triggered a water stress response showing higher stomatal sensitivity to changes in air vapour pressure deficit, relatively low assimilation rates, high intrinsic and extrinsic water-use efficiency (WUE) and earlier cessation of shoot growth. Yet, mid-morning leaf water potential was consistently lower in HS treatment over stress as compared to WW, indicating an anisohydric adjustment. Canopy NCER given on a leaf-area basis showed mean daily rates ranging from 3.9 to 4.9 μmol m² s^?1 in WW canopies against 2.6–3.0 μmol m^?2 s^?1 in HS. Conversely, canopy transpiration rates varied from 0.915 to 1.157 mmol m^?2 s^?1 for WW to 0.630–0.714 mmol m² s^?1 in HS. Increased leaf-based intrinsic and extrinsic WUE in HS did not match the canopy response, which to some extent resulted in an opposite outcome, i.e. higher canopy WUE in well-watered vines especially in the morning hours. Likewise, δ¹³C did not differ between treatments. This suggests caution when point-time determinations of single-leaf-based WUE are extrapolated to the whole-canopy behaviour when assessing the water saving strategies of a given genotype. The stressed vines achieved no variation in yield level and components and had improved grape composition as to soluble solids and total anthocyanins. This optimal behaviour is likely due to earlier shoot growth cessation, enhanced maturity and a buffering leaf-to-fruit ratio (3.61 m² kg^?1) that mitigated the effects of post-veraison stress.     

Changes in soil respiration across a chronosequence of tallgrass prairie reconstructions

Close relationships among climatic factors and soil respiration (R_s) are commonly reported. However, variation in R_s across the landscape is compounded by site-specific differences that impede the development of spatially explicit models. Among factors that influence R_s, the effect of ecosystem age is poorly documented. We hypothesized that R_s increases with grassland age and tested this hypothesis in a chronosequence of tallgrass prairie reconstructions in central Iowa, U.S.A. We also assessed changes in root biomass, root ingrowth, aboveground net primary productivity (ANPP), and the strength of soil temperature and moisture in predicting R_s. We found a significant increase in total growing season R_s with prairie age (R² = 0.79), ranging from 714 g C m^?2 in the youngest reconstruction (age 4) to 939 g C m^?2 in the oldest prairie (age 12). Soil temperature was a strong predictor of intra-seasonal R_s among prairies (R² = 0.78–0.87) but mean growing season soil temperature and moisture did not relate to total R_s. The increase in R_s with age was positively correlated with root biomass (r = 0.80) and ANPP (r = 0.87) but not with root ingrowth. Our findings suggest that growing season R_s increases with tallgrass prairie age, root biomass, and ANPP during young grassland development.     

Reduction of hexavalent chromium by polypyrrole-modified steel mesh electrode

Adherent polypyrrole (ppy) films were electropolymerized from a para-toluenesulfonic sodium (PTS) solution on stainless steel mesh (SSM). Reduced ppy-modified SSM electrode can transfer Cr(VI) to Cr(III) effectively. Lower pH (<2) or higher temperature (>35 °C) is beneficial for the removal of Cr(VI). Electro-reduction achieved 90% removal efficiency after 21 min by cyclic voltammetry. The removal efficiency is 96–56% for one–six contact cycles between ppy and Cr(VI). SEM shows that ppy films on SSM have regular morphology with small nucleus of less than 1 μm in diameter.     

Biogas production from maize and dairy cattle manure—Influence of biomass composition on the methane yield

There is an increasing world wide demand for energy crops and animal manures for biogas production. To meet these demands, this research project aimed at optimising anaerobic digestion of maize and dairy cattle manures. Methane production was measured for 60 days in 1 l eudiometer batch digesters at 38 °C. Manure received from dairy cows with medium milk yield that were fed a well balanced diet produced the highest specific methane yield of 166.3 Nl CH₄ kg VS⁻¹. Thirteen early to late ripening maize varieties were grown on several locations in Austria. Late ripening varieties produced more biomass than medium or early ripening varieties. On fertile locations in Austria more than 30 Mg VS ha⁻¹ can be produced. The methane yield declined as the crop approaches full ripeness. With late ripening maize varieties, yields ranged between 312 and 365 Nl CH₄ kg VS⁻¹ (milk ripeness) and 268–286 Nl CH₄ kg VS⁻¹ (full ripeness). Silaging increased the methane yield by about 25% compared to green, non-conserved maize. Maize (Zea mays L.) is optimally harvested, when the product from specific methane yield and VS yield per hectare reaches a maximum. With early to medium ripening varieties (FAO 240–390), the optimum harvesting time is at the “end of wax ripeness”. Late ripening varieties (FAO ca. 600) may be harvested later, towards “full ripeness”. Maximum methane yield per hectare from late ripening maize varieties ranged between 7100 and 9000 Nm³ CH₄ ha⁻¹. Early and medium ripening varieties yielded 5300–8500 Nm³ CH₄ ha⁻¹ when grown in favourable regions. The highest methane yield per hectare was achieved from digestion of whole maize crops. Digestion of corns only or of corn cob mix resulted in a reduction in methane yield per hectare of 70 and 43%, respectively. From the digestion experiments a multiple linear regression equation, the Methane Energy Value Model, was derived that estimates methane production from the composition of maize. It is a helpful tool to optimise biogas production from energy crops. The Methane Energy Value Model requires further validation and refinement.     

Evaluation of the effectiveness of low frequency workpiece vibration in deep-hole micro-EDM drilling of tungsten carbide

The application of micro-electrical discharge machining (micro-EDM) in deep-hole drilling is still limited due to the difficulty in flushing of debris and unstable machining. Present study introduces a simplistic analytical model to evaluate the effectiveness of low frequency workpiece vibration during the micro-EDM drilling of deep micro-holes. In addition, experimental investigation has been conducted to validate the model by studying the effects of workpiece vibration on machining performance, surface quality and dimensional accuracy of the micro-holes. The effect of vibration frequency and amplitude for three different settings of aspect ratios has been studied experimentally. Moreover, the vibration experiments have been conducted at different levels of gap voltages and capacitances in order to understand the effect of electrical parameters and effectiveness of low-frequency workpiece-vibration at different levels of discharge energies. It has been shown analytically that the effectiveness of low frequency workpiece vibration during micro-EDM drilling can be evaluated by a parameter ‘K_v’ (ratio of maximum acceleration of the vibrating plate in gravitational direction to gravitational acceleration ‘g’), which can be determined from the vibration frequency, amplitude and phase angle of the vibrating workpiece. The theoretical model reveals that for K_v > 1, the position of debris particles will be above the workpiece; thus can be flushed away from machined zone effectively. The experimental reasons for improved micro-EDM drilling performance at the setting of K_v > 1 are found to be the increased effective discharge ratio, reduced short-circuits and improved dielectric flushing. The experimental results also reveal that the low frequency vibration is more effective at the low discharge energy level, thus making it more suitable for micro-EDM. Considering the effect on both the machining characteristics and micro-hole accuracy parameters, vibration frequency of 750 Hz and amplitude of 1.5 μm was found to provide improved performance for the developed vibration device.     

Effect of air-exposed biocathode on the performance of a Thauera-dominated membraneless single-chamber microbial fuel cell (SCMFC)

To investigate the effect of air-exposed biocathode(AEB) on the performance of singlechamber microbial fuel cell(SCMFC), wastewater quality, bioelectrochemical characteristics and the electrode biofilms were researched. It was demonstrated that exposing the biocathode to air was beneficial to nitrogen removal and current generation. In Test 1 of 95%AEB, removal rates of ammonia, total nitrogen(TN) and chemical oxygen demand(COD)reached 99.34% ± 0.11%, 99.34% ± 0.10% and 90.79% ± 0.12%, respectively. The nitrogen removal loading rates were 36.38 g N/m~3/day. Meanwhile, current density and power density obtained at 0.7 A/m3 and 104 m W/m~3 respectively. Further experiments on opencircuit(Test 2) and carbon source(Test 3) indicated that this high performance could be attributed to simultaneous biological nitrification/denitrification and aerobic denitrification, as well as bioelectrochemical denitrification. Results of community analysis demonstrated that both microbial community structures on the surface of the cathode and in the liquid of the chamber were different. The percentage of Thauera, identified as denitrifying bacteria, maintained at a high level of over 50% in water, but decreased gradually in the AEB. Moreover, the genus Nitrosomonas, Alishewanella, Arcobacter and Rheinheimera were significantly enriched in the AEB, which might contribute to both enhancement of nitrogen removal and electricity generation.     

Ammonia and nitrous oxide emissions following land application of high and low nitrogen pig manures to winter wheat at three growth stages

Nitrous oxide (N₂O) and ammonia (NH₃) emissions from surface applied high (HN) and low (LN) nitrogen pig manures were measured under field conditions. Manures were band-spread to a winter wheat crop at three growth stages—mid-tillering, stem elongation and flag leaf emergence. The N₂O flux rates were measured using the static chamber technique while NH₃ volatilisation was assessed using a micrometeorological mass balance technique with passive flux samplers. The N₂O emissions were episodic in nature with flux rates observed ranging from 2.8 to 31.5 g N₂O–N ha^?1 day^?1 (P < 0.001). Higher N₂O emissions generally occurred after rainfall events. Highest N₂O losses were observed from the HN treatment with LN manure use decreasing emissions by 18% (P < 0.03). The NH₃ volatilisation rates were highest within 1 h of manure application with 95% of emissions occurring within 24 h (P < 0.001). Cumulative N loss was highest at mid-tillering as low crop canopy cover and increased wind-speeds enhanced NH₃ loss (P < 0.001). Highest emissions were measured from the HN manure (P < 0.03). Total ammoniacal N loss ranged from 6 to 11%. Crop N uptake and grain yield were unaffected by application timing or manure type. Therefore, the use of LN manures decreased gaseous emissions of N₂O and NH₃ without any adverse effects on crop performance.     

Effects of surfactants on the combined toxicity of TiO2 nanoparticles and cadmium to Escherichia coli

The combined ecological toxicity of TiO₂ nanoparticles (nano-TiO₂) and heavy metals has been paid more attention. As the common pollutants in water environment, surfactants could affect the properties of nanoparticles and heavy metals, and thus further influence the combined toxicity of nano-TiO₂ and heavy metals. In this study, the effects of sodium dodecyl benzene sulfonate (SDBS) and Tween 80 on the single and combined toxicities of Cd^2 + and nano-TiO₂ to Escherichia coli (E. coli) were examined, and the underlying influence mechanism was further discussed. The results showed both SDBS and Tween 80 enhanced the toxicity of Cd^2 + to E. coli in varying degrees. The reaction of SDBS and Cd^2 + could increase the outer membrane permeability and the bioavailability of Cd, while Tween 80 itself could enhance the outer membrane permeability. The combined toxicity of nano-TiO₂ and Cd^2 + to E. coli in absence of surfactant was antagonistic because of the adsorption of Cd^2 + to nano-TiO₂ particles. However, in the presence of SDBS, both SDBS and nano-TiO₂ influenced the toxicity of Cd^2 +, and also SDBS could adsorb to nano-TiO₂ by binding to Cd^2 +. The combined toxicity was reduced at Cd^2 + lower than 4 mg/L and enhanced at Cd^2 + higher than 4 mg/L under multiple interactions. Tween 80 enhanced the combined toxicity of nano-TiO₂ and Cd^2 + by increasing the outer membrane permeability. Our study firstly elucidated the effects of surfactants on the combined toxicity of nano-TiO₂ and Cd^2 + to bacteria, and the underlying influencing mechanism was proposed.     

Emissions of N2O and NH3, and nitrogen leaching from direct seeded rice under different tillage practices in central China

Tillage practices affect the fate of fertilizer nitrogen (N) through influencing transformations of N, but few studies have examined N₂O and NH₃ emissions, and N leaching from different rice tillage systems. Thus the objective of this study was to assess N₂O emission, NH₃ volatilization and N leaching from direct seeded rice in conventional tillage (CT) and no-tillage (NT) production systems in the subtropical region of China during the 2008 and 2009 rice growing seasons. Treatments were established following a split-plot design of a randomized complete block with tillage practices as the main plot and N fertilizer level as the sub-plot treatment, and there were four treatments: NT + no fertilizer (NT0), CT + no fertilizer (CT0), NT + compound fertilizer (NTC) and CT + compound fertilizer (CTC), respectively. Results showed that N fertilization significantly increased (p < 0.01) N₂O emissions, NH₃ volatilization and N leaching from rice fields in both years. In general, there was no significant difference in N₂O emissions and NH₃ volatilization between NT0 and CT0 in both years, while NTC had significantly higher (p < 0.05) N₂O emissions and NH₃ volatilization compared to CTC. Over the two rice growing seasons, NTC showed 32% and 47% higher N₂O emissions, and 29% and 52% higher NH₃ losses than CTC. Higher (p < 0.05) N₂O emissions from NTC than CTC were presumably due to higher soil organic C and greater denitrification. Total N and NO₃^? concentrations were higher (p < 0.05) in CTC than NTC, but larger volumes of percolation water in NTC than CTC resulted in no significant difference in leakage of total N and NO₃^?. Hence, application of N fertilizer in combination with NT appeared to be ineffective in reducing N losses from N fertilizer in paddy fields.     

Hermetic joining of 316L stainless steel using a patterned nickel nanoparticle interlayer

This paper evaluates the use of a nickel nanoparticle (NiNP) interlayer for making hermetic joints in 316L stainless steel substrates via diffusion brazing. Different NiNP inks were prepared using commercial nanopowder (～9 nm) and in-house synthesized nanoparticles. Syringe pump deposition of ～9 nm NiNP ink and diffusion brazing at 900 °C for 30 min under 2 MPa resulted in a hermetic joint up to the tested pressure of 70 psi. In-house synthesis of NiNPs was carried out in ethylene glycol by the reduction of NiCl₂·6H₂O in the presence of hydrazine (N₂H₄) as a reducing agent. X-ray diffraction (XRD) analysis and transmission electron microscopy (TEM) results confirm the presence of pure fcc-Ni with an average particle size of 5.4 ± 0.9 nm. An as-synthesized suspension of NiNPs was patterned onto 316L stainless steel laminae via automated dispensing to a thickness of ～3 μm and bonded at 800 °C for 30 min at a pressure of 2 MPa. The diffusion-brazed test article was also found to be hermetic up to 70 psi. An examination of the bond line using scanning electron microscopy (SEM) showed good uniformity and continuity.     

The influence of long term trends in pollutant emissions on deposition of sulphur and nitrogen and exceedance of critical loads in the United Kingdom

In the United Kingdom, as with other European countries, land-based emissions of NO_x and SO₂ have fallen significantly over the last few decades. SO₂ emissions fell from a peak of 3185 Gg S in 1970 to 344 Gg S in 2005 and are forecast by business-as-usual emissions scenarios to fall to 172 Gg by 2020. NO_x emissions were at a maximum of 951 Gg N in 1970 and fell to 378 by 2005 with a further decrease to 243 Gg N forecast by 2020. These large changes in emissions have not been matched by emissions changes for NH₃ which decreased from 315 Gg N in 1990 to 259 in 2005 and are forecast to fall to 222 by 2020. The Fine Resolution Atmospheric Multi-pollutant Exchange model (FRAME) has been applied to model the spatial distribution of sulphur and nitrogen deposition over the United Kingdom during a 15-year time period (1990–2005) and compared with measured deposition of sulphate, nitrate and ammonium from the national monitoring network. Wet deposition of nitrogen and sulphur was found to decrease more slowly than the emissions reductions rate. This is attributed to a number of factors including increases in emissions from international shipping and changing rates of atmospheric oxidation. The modelled time series was extended to a 50-year period from 1970 to 2020. The modelled deposition of SO_x, NO_y and NH_x to the UK was found to fall by 87%, 52% and 25% during this period. The percentage area of sensitive habitats in the United Kingdom for which critical loads are exceeded is estimated to fall from 85% in 1970 to 37% in 2020 for acidic deposition and from 73% to 49% for nutrient nitrogen deposition. The significant reduction in land emissions of SO₂ and NO_x focuses further attention in controlling emissions from international shipping. Future policies to control emissions of ammonia from agriculture will be required to effect further significant reductions in nitrogen deposition.