Passive sampling of perfluorinated acids and sulfonates using polar organic chemical integrative samplers

The applicability of a polar organic chemical integrative sampler (POCIS) for detection and determination of perfluorinated acids and sulfonates in water was studied under field conditions. Standard POCIS configurations (i.e., pharmaceutical and pesticide) were deployed in effluent from a wastewater treatment plant for 1, 2, and 3 weeks. Ten of 15 target compounds were found in POCIS, five of which were quantified in wastewater. Pest-POCIS appeared more effective for the sampling, while Pharm-POCIS had a more rapid uptake kinetic, which leads to faster saturation or equilibrium. The results showed that the pesticide configuration is probably more suitable for the sampling of this class of compounds. Based on average concentration in water over the sampling period and amount of compound adsorbed in the POCIS, we calculated sampling rates for five studied compounds and obtained values of 0.034 to 0.222 L?day^?1.     

Myxococcus xanthus'' killed cells as inducers of struvite crystallization. Its possible role in the biomineralization processes

We studied the possibility of struvite formation using killed cells of Myxococcus xanthus. Cells were killed by heat, UV light and sonication. In all cases, we show that struvite crystallization occurs and we propose that the dead cells or cell debris can act by themselves as heterogeneous crystallization nuclei. We also show that the slime, produced by Myxococcus in a large quantities, is not involved in this process.     

Estimating half-lives of pesticides in/on vegetation for use in multimedia fate and exposure models

Degradation half-lives in/on vegetation are needed in environmental risk assessment of pesticides, but these data are often not available for most active ingredients. To address this, we first correlated experimental soil degradation half-life data of 41 pesticides obtained from the reviewed literature with the corresponding experimental half-lives on plant surface. Degradation half-lives in soil were found to be four times slower compared with half-lives on plant surfaces. In a second step, we explored measured plant surface half-lives directly with those in vegetation. The results were validated by comparing computed values with results obtained from an experimental set-up. The uptake and dissipation of alpha-cypermethrin (insecticide) and bromopropylate (acaricide) was studied by detecting pesticide residues in whole and peeled tomato fruits using gas chromatography. Half-lives within vegetation were found to be four times faster compared with plant surface half-lives. Using this experimental based approach, it is concluded that the estimation of degradation half-lives of pesticides in/on vegetation to be used as input data in environmental mass balance models can be directly correlated from the more abundant ready experimental degradation half-life data for soil.     

The use of a lacertid lizard as a model for reptile ecotoxicology studies--part 1 field demographics and morphology

At the European level, lacertid lizards have been proposed as potential model species for reptile ecotoxicology. We studied demographic and morphological aspects of natural field subpopulations of Podarcis bocagei inhabiting similar agricultural habitats which were either regularly exposed to pesticides, or not. Parameters examined in this study included population size and density, sex ratio, adult body size, fluctuating asymmetry in femoral pores and parasite prevalence. In general, we detected few statistically significant differences between the exposed and reference subpopulations. Although field situations are ecologically complex and factors other than pesticides may be acting, the absence of observable effects on field subpopulations is probably indicative that lizards are coping or compensating for this level of exposure.     

中国电力工业烟气脱硫的现状及发展趋势

研究我国电力工业燃煤发电厂烟气脱硫的现状及其发展趋势 ,包括我国电力工业大气SO2 污染状况 ,烟气脱硫现状 ,烟气脱硫综合经济技术评价 ,烟气脱硫技术的选择和烟气脱硫的发展趋势。研究与开发有针对性和较强应用前景的烟气脱硫技术 ,发展具有独立自主知识产权的烟气脱硫技术 ,是我国电力工业烟气脱硫技术及设备国产化的必经之路     

Assessment of DDT, DDE, and 1-hydroxypyrene levels in blood and urine samples in children from Chiapas Mexico

Purpose

The aim of this study was assess co-exposure to DDT, DDE (main DDT metabolite), and PAHs (1-hydroxypyrene) in areas where biomass is used to cook and to heat homes and where DDT was used to combat malaria transmission.

Methods

During 2009, we analyzed a total of 190 blood and urine samples from children living in six communities in Mexico. Quantitative analyses of DDT and DDE were performed using gas chromatography coupled with mass spectrometry. Analyses of 1-hydroxypyrene were performed by HPLC using a fluorescence detector.

Results

In this work, we found high levels of DDT and its principal metabolite (DDE) in the blood of children living in four communities in Chiapas located in the southeastern region of Mexico (range, Conclusion This study demonstrates that children in these communities were exposed to DDT and its metabolites, and to other contaminants generated by the combustion of firewood. Therefore, the complex mixture studied in this study (PAHs and DDT/DDE) requires further research.     

Assessment of the rhizosphere competency and pentachlorophenol-metabolizing activity of a pesticide-degrading strain of Trichoderma harzianum introduced into the root zone of corn seedlings

To develop a dependable approach to introduce laboratory selected, pesticide-degrading microorganisms into soil environments for the purpose of in situ bioremediation, we tested the possibility of utilizing plant rhizospheres as the vehicle. We first established the rhizosphere competency of a strain of the soil fungus Trichoderma harzianum, a biocontrol species well studied by plant pathologists to colonize plant rhizosphere in many parts of the world. The strain we chose, T.h.2023 is resistant to many fungicides, and it has been shown to metabolize several pesticides. Second, we found that it readily metabolized pentachlorophenol (PCP), which is quickly and stochiometrically converted to pentachloroanisole (PCA) in liquid culture. Taking advantage of this specific feature, we have developed a sensitive metabolic marker approach that allowed us to monitor for the continuous presence and activity of this fungal strain in the corn rhizosphere soil in situ over time.     

Adsorption of simazine on zeolite H-Y and sol–gel technique manufactured porous silica: A comparative study in model and natural waters

In this work, we studied the removal of simazine from both a model and well water by adsorption on two different adsorbents: zeolite H-Y and a porous silica made in the laboratory by using the sol–gel technique. The pH dependence of the adsorption process and the isotherms and pseudo-isotherms of adsorption were studied. Moreover, an iterative process of simazine removal from both the model and well water, which allowed us to bring the residual simazine concentration below the maximum concentration (0.05 mg L^?1) of agrochemicals in wastewater to be released in surface waters or in sink allowed by Italian laws, was proposed. The results obtained were very interesting and the conclusions drawn from them partly differed from what could reasonably be expected.     

The survey of PCDDs and PCDFs in the ambient air of the urban and industrial sites in Korea, 1998-99

A comprehensive quality survey for PCDDs/PCDFs in ambient air has been studied in Korea for two years. Monitoring was undertaken at two locations throughout Seoul (urban site) and Incheon (industrial site) in winter and spring. The periods are during 16 to 17 March 1998, 21 to 22 January 1999 and 28 to 29 April 1999 (Seoul) and 25 to 26 March 1998, 18 to 19 January 1999 and 26 to 27 April 1999 (Incheon). The values of PCDDs/PCDFs in ambient air were expressed as concentrations and international TEF values. The contents of PCDDs/PCDFs in urban site (Seoul) were lower than in industrial site (Incheon). The measurements in wintertime were higher than in springtime. The contents of 2,3,4,7,8-PeCDF with half toxicity of 2,3,7,8-TCDD were high. Thus we assumed to have an interest to the contents of 2,3,4,7,8-PeCDF. In this study, sample size was small (sample number was only 18) and sampling period was limited by 24 h. Therefore, we need more widespread and long-term surveys in order to estimate the human exposure by inhalation.     

Bacterial diversity and function in the Baltic Sea with an emphasis on cyanobacteria

In this article we summarize the current knowledge of Baltic Sea cyanobacteria, focusing on diversity, toxicity, and nitrogen fixation in the filamentous heterocystous taxa. We also review the recent results of our microbial diversity studies in planktonic and benthic habitats in the Baltic Sea. Based on molecular analyses, we have improved the understanding of cyanobacterial population structure by assessing genetic diversity within species that are morphologically inseparable. Moreover, we have studied microbial functions such as toxin production and nitrogen fixation in situ under different environmental conditions. Phosphorus limitation of bloom-forming, nitrogen-fixing cyanobacteria was clearly verified, emphasizing the importance of continuous efforts to reduce this element in the Baltic Sea. We have designed a rapid and reliable detection method for the toxic cyanobacterium Nodularia spumigena, which can be used to study bloom formation of this important toxin producer.     

Application of coupled thermostatted columns in civil engineering and for leaching heavy metals of wastes from foundry sands and mining industry

For many years, the mining industry at Pachuca Hidalgo, Mexico, has produced silver and gold through a cyanide process. Solid wastes (tailings) of this process have been deposited close to centres of population. Many of the metals in these wastes are dispersed via wind and rain, and can be toxic to flora and fauna. Foundry sands are wastes, produced by the automotive industry, the metallurgy industry and others, which are contaminated with many metals such as Fe, Cr, Zn, Pb, Au Ag, Ti, Ge, Co, As, Al, etc. We have previously patented a process for the extraction of toxic and valuable metals from foundry sands using a thermostatted column. The results of this study indicate that the process and the device could be used for removing heavy metals from tailings. In this research both types of waste (foundry sands and tailings) were leached using four coupled thermostatted columns. The presence of heavy metals in the solid wastes was studied using the ICP-AS technique and scanning electron microscopy, and to study the structure we used X-ray diffraction. After leaching we used the solid wastes (without toxic metals) to produce bricks. The mechanical properties of the bricks were assessed against international standards.     

曝气-絮凝处理垃圾渗滤液研究

通过现场处理 ,对垃圾渗滤液的曝气 -絮凝处理进行了研究。结果表明该方法对渗滤液的色度、COD、总磷去除率达 80 %以上 ,对氨氮去除率达 60 %以上。在此基础上提出了最优综合控制指标     

Characteristics of photocatalytic oxidation of toluene, benzene, and their mixture

The investigation of the photocatalytic oxidation (PCO) of multicomponent volatile organic compounds (VOCs) is very important to the application of PCO technology, because there is seldom a single VOC component in indoor air. In this paper, the characteristics of binary indoor VOCs, toluene and benzene, were experimentally studied using a mass transfer based method that we developed. The concentration ranges for toluene and benzene were 4.48-27.4 mg/m3 and 1.82-4.08 mg/m3, respectively. We found the following: (1) the PCO of each individual contaminant studied obeys the unimolecular form of the Langmuir-Hinshelwood (L-H) rate form; (2) the PCO of the binary contaminants follow the competitive adsorption L-H rate form; (3) the reaction-coefficient for PCO of individual contaminants differs from that in the competitive adsorption L-H rate form; and (4) the component impact factor of A to B, put forward in this paper, is a useful parameter describing the influence of A on the reaction coefficient of B, and it was found that the impact factor of toluene (a chemically active component) on benzene (a chemically stable component) is high, and the impact factor of benzene on toluene is low.     

Impact of polycyclic aromatic hydrocarbon emissions from medical waste incinerators on the urban atmosphere

In this study, polycyclic aromatic hydrocarbon (PAH) emissions from two batch-type medical waste incinerators (MWIs), one with a mechanical grate and the other with a fixed grate, both operated by a medical center, were assessed. Both MWIs shared the same air-pollution control devices (APCDs), with an electrostatic precipitator and a wet scrubber installed in series. Results show that when APCDs were used, total PAHs and total benzo[a]pyrene equivalent (total BaP(eq)) emission concentrations of both MWIs were reduced from 2220 to 1870 microg/m3 and 50 to 12.4 microg/m3, respectively. We used the Industrial Source Complex Short Term model (ISCST) to estimate the ground-level concentrations of the residential area and the traffic intersection located at the downwind side of the two MWIs. For the traffic intersection, we found both total PAHs and total BaP(eq) transported from MWIs to both studied areas were not significant. For the residential area, similar results were found when APCDs were used in MWIs. When APCDs were not included, we found that total PAHs transported from MWIs accounted for < 12%, but total BaP(eq) accounted for > 90%, of the on-site measured concentrations. These results suggest that the use of proper APCDs during incineration would significantly reduce the carcinogenic potencies associated with PAH emissions from MWIs to the residential area.     

Personal carbon monoxide exposure in five European cities and its determinants

Studies involving carbon monoxide (CO) exposure assessment are mainly based on measurements at outdoor fixed sites or in various indoor micro-environments. Few studies have been based on personal exposure measurements. In this paper, we report results on personal measurements of CO in five European cities and we investigate determinants which may influence this personal exposure.Within the multi-centre European EXPOLIS study, personal exposure to CO, measured every minute for 48 h, of 401 randomly selected study participants (mainly non-smokers) was monitored in Athens, Basle, Helsinki, Milan and Prague. Each participant also completed a time-microenvironment-activity diary and an extended questionnaire. In addition, for the same time period, ambient levels of CO from fixed site stations were collected.There are significant differences in both personal exposure and ambient levels within the five cities, ranging from high values in Milan and Athens to low in Helsinki. Ambient levels are a significant correlate and determinant of CO 48-h personal exposure in all cities. From the other determinants studied (time spent in street traffic, time of exposure to ETS and time of exposure to gas burning devices) none was consistently significant for all cities. Change of the ambient CO levels from the 25th to the 75th percentile of its distribution resulted in a 1.5–2 fold increase of 48-h personal exposure. Short time personal exposure was also studied in order to assess the influence of specific sources. Exposure levels were significantly higher when participants were in street traffic and in indoor locations in the presence of smokers.Personal 48-h exposure of non-smokers to CO varies among urban populations depending primarily on the ambient levels. For a CO source to be a significant determinant of the personal 48-h CO exposure, it has to affect the levels of CO in the person's proximity for an adequate length of time. Activities of individuals affect shorter term personal exposure.     

Change of magnetic properties due to fluctuations of hydrocarbon contaminated groundwater in unconsolidated sediments

Sediments affected by fluctuations of hydrocarbon contaminated groundwater were studied at a former military site. Due to remediation, groundwater table fluctuation (GWTF) extends over approximately one meter. Three cores were collected, penetrating through the GWTF zone. Magnetic parameters, sediment properties and hydrocarbon content were measured. We discovered that magnetic concentration parameters increased towards the top of the GWTF zone. Magnetite is responsible for this enhancement; rock magnetic parameters indicate that the newly formed magnetite is in a single domain rather than a superparamagnetic state. The presence of hydrocarbons is apparently essential for magnetite to form, as there is clearly less magnetic enhancement in the core, which is outside of the strongly contaminated area. From our results we conclude that the top of the fluctuation zone has the most intensive geomicrobiological activity probably responsible for magnetite formation. This finding could be relevant for developing methods for simply and quickly detecting oil spills.     

Study of the toxicity of diuron and its metabolites formed in aqueous medium during application of the electrochemical advanced oxidation process "electro-Fenton"

Diuron (N'-[3,4-dichlorophenyl]-N,N-dimethylurea) is a herbicide belonging to the phenylurea family, widely used to destroy weeds on uncultivated surfaces. Because of its toxicity for aquatic organisms and suspicion of being carcinogenic for humans, diuron is the object of growing environmental concern. Therefore, we have developed the electro-Fenton method, an electrochemical advanced oxidation process (EAOP), to degrade diuron in aqueous medium, and we have studied the evolution of the toxicity of treated solution during the process. Indeed, the EAOPs catalytically generate hydroxyl radicals that oxidize the persistent organic pollutants, and can ultimately destroy and mineralize them. But, sometimes, relatively toxic organic metabolites are formed during the oxidation reaction. In this work, the evolution of toxicity of diuron aqueous solutions was studied at different initial concentrations, during treatment by the electro-Fenton method. Samples were collected at various electrolysis times and mineralization degrees during the treatment. The toxicity of the samples was measured using the bacteria Vibrio fischeri (Microtox) and the green alga Scenedesmus obliquus. Our results demonstrated that the toxicity of diuron aqueous solutions (concentrations=3.0-27.6 mg L(-1)) varied considerably with time. The formation and disappearance of several metabolites, having toxicity often stronger than that of the initial herbicide, were observed. To improve the efficiency of water decontamination, the electro-Fenton method should be applied during a time long enough (several hours) and at relatively high electrolysis current (I=250 mA) to reach a nearly complete mineralization of the herbicide in the aqueous medium.     

Degradation of toxaphene in aged and freshly contaminated soil

Degradation of toxaphene in soil from both newly contaminated (from Sweden) and aged spills (from Nicaragua) were studied. The newly contaminated soil contained approximately 11 mg kg(-1) toxaphene while the aged Nicaraguan soil contained approximately 100 mg kg(-1). Degradation was studied in anaerobic bioreactors, some of which were supplied with lactic acid and others with Triton X-114. In this study we found that the lower isomers Parlar 11, 12 were degraded while the concentration of isomer Parlar 15 increased. This supported an earlier evaluation which indicated that less chlorinated isomers are formed from more heavily isomers. Lactic acid when added to the soil, interfere with the degradation of toxaphene. Lactic acid was added; several isomers appeared to degrade rather slowly in newly contaminated Swedish soil. The Swedish soil, without any external carbon source, showed the slowest degradation rate of all the compounds studied. When Triton X-114 at 0.4 mM was added, the degradation rate of the compounds increased. This study illustrates that biodegradation of toxaphene is a complex process and several parameters have to be taken into consideration. Degradation of persistent pollutants in the environment using biotechnology is dependent on bioavailability, carbon sources and formation of metabolites.     

Physicochemical and biological characterisation of different dredged sediment deposit sites in France

The aim of this work is to determine sediment properties, metal contents and transfers of Cd and Zn from dredged sediments to plants. To this end 10 deposit sites with different contexts were visited in France. The main agronomic characteristics and metal contents for surface soil layers were measured, the plant species present at the sites, such as Brassicaceae and Fabaceae, were listed, and the distribution of their root systems described. Soil characteristics such as available P (Olsen) varied between sites, with values ranging from 0.01 to 0.49 g kg(-1). Total contents and enrichment factors were studied, highlighting metal contamination in most of the sites. Despite carrying out principal component analyses, it was not possible to group deposits by age or geographical localisation. However, deposits could be distinguished as a function of proximity of industrial facilities, sediment grain size and carbonate content. Associations between metals were also highlighted: (1) Cd, Pb and Zn, and (2) Al, Cr, Cu and Fe. Consequently, we propose classifying them as technogenic anthrosols.