Resuspension of contaminated field and formulated reference sediments Part I: Evaluation of metal release under controlled laboratory conditions

In aquatic systems where metal contaminated sediments are present, the potential exists for metals to be released to the water column when sediment resuspension occurs. The release and partitioning behavior of sediment-bound heavy metals is not well understood during resuspension events. In this study, the release of Cd, Cu, Hg, Ni, Pb and Zn from sediments during resuspension was evaluated using reference sediments with known physical and chemical properties. Sediment treatments with varying quantities of acid volatile sulfide (AVS), total organic carbon (TOC), and different grain size distributions were resuspended under controlled conditions to evaluate their respective effects on dissolved metal concentrations. AVS had the greatest effect on limiting release of dissolved metals, followed by grain size and TOC. Predictions of dissolved concentrations of Cd, Ni, Pb and Zn were developed based on the formulated sediment Σ_metal/AVS ratios with Σ_metal being the total sediment metal concentration. Predicted values were compared to measured dissolved metal concentrations in contaminated field sediments resuspended under identical operating conditions. Metal concentrations released from the field sediments were low overall, in most cases lower than predicted values, reflecting the importance of other binding phases. Overall, results indicate that for sulfidic sediments, low levels of the study metals are released to the dissolved phase during short-term resuspension.     

Metal partitioning in river sediments measured by sequential extraction and biomimetic approaches

We quantified the concentrations and distributions of metals (Cd, Cr, Cu, Ni, Pb, and Zn) in the sediments of Tuen Mun River, Hong Kong. The potential bioavailability of metals was assessed with a biomimetic extraction method using the sipunculan gut juices. The sediments were characterized by relatively high concentrations of trace metals. Field collected sediments were highly anoxic and the ratio of simultaneously extractable metal (sigmaSEM) to acid volatile sulfide (AVS) was much less than one in these sediments. The majority (>67%) of Cd, Pb, and Zn were bound to AVS, thus their concentrations in the sediment porewater were low. In contrast, Ni was little bound to AVS due to its lower ratios of SEM-Ni to total Ni concentrations. For Cu, relatively high concentrations in the sediment porewater was found, and total organic carbon, AVS and other resistant sulfide phase were the controlling factors for sedimentary Cu partitioning. Net metal adsorption from gut juices to anoxic sediments was observed in metal extraction experiments, suggesting that AVS determined the bioaccumulation and potential bioavailability of most metals in these sediments. Extraction of metals from the oxidized sediments by the gut juices was mainly attributed to metal redistribution from AVS to other geochemical phases. The gut juices were the most effective solvent or extractant than the simple electrolyte solution [I (NaNO(3)) = 0.01 M] and the natural overlying water. Cd was more easily extracted from the oxidized sediments than Zn that tended to have a stronger binding affinity with Fe-Mn oxide, clay and organic matter. The application of partial removal techniques in metal extraction experiments further demonstrated the differential controls of various sediment geochemical phases in affecting metal bioavailability, with the order of TOC > Fe-Mn oxides > carbonate.     

Oxidation of acid-volatile sulfide in surface sediments increases the release and toxicity of copper to the benthic amphipod Melita plumulosa

Acid-volatile sulfides (AVS) are an important metal-binding phase in sediments. For sediments that contain an excess of AVS over simultaneously extracted metal (SEM) concentrations, acute or chronic effects should not result from the metals Cd, Cu, Ni, Pb and Zn. While AVS phases may exist in surface sediments, the exposure to dissolved oxygen may oxidize the AVS and release metals to more bioavailable forms. We investigated the role of oxidation of AVS, and specifically copper sulfide phases, in surface sediments, in the toxicity to juveniles of the epibenthic amphipod, Melita plumulosa. Sediments containing known amounts of copper sulfide were prepared either in situ by reacting dissolved copper with AVS that had formed in field sediments or created in sediments within the laboratory, or by addition of synthesised CuS to sediments. Regardless of the form of the copper sulfide, considerable oxidation of AVS occurred during the 10-d tests. Sediments that had a molar excess of AVS compared to SEM at the start of the tests, did not always have an excess at the end of the tests. Consistent with the AVS-SEM model, no toxicity was observed for sediments with an excess of AVS throughout the tests. However, the study highlights the need to carefully consider the changes in AVS concentrations during tests, and that measurements of AVS and SEM concentrations should carefully target the materials to which the organisms are being exposed throughout tests, which in the case of juvenile M. plumulosa is the top few mm of the sediments.     

Vertical distribution of acid-volatile sulfide and simultaneously extracted metals in mangrove sediments from the Jiulong River Estuary,Fujian, China

Background Acid-volatile sulfide (AVS) is operationally defined as sulfides in sediment, which are soluble in cold acid, and is reported as the most active part of the total sulfur in aquatic sediments. It is a key partitioning phase controlling the activities of divalent cationic heavy metals in sediment. Methods In order to examine this in mangrove environments, six sites were selected along the Jiulong River Estuary in Fujian, China, which had previously been reported to be polluted by heavy metals. Sediments were sampled from 0–60 cm depth at each site, and the spatial distribution of AVS and SEM (simultaneously extracted metals: copper, cadmium, zinc, and lead) were determined. Results and Discussion The results indicate that the AVS concentrations had a spatial variation, ranging from 0.24 to 16.10 μmol g⁻¹ sediment dry weight. The AVS concentration in the surface layer is lower than that of the deeper sediment, with peak values in the 15–30 cm horizon. There was no correlation between the AVS value and organic matter content or total dissolved salts, but a significant positive correlation of AVS with surface sediment (0–5 cm) moisture content was found. This indicates that water logged sediments tend to have a high AVS value. The amount of SEM was within the range of 0.33–2.80 μmol g⁻¹ sediment dry weight and decreased with sediment depth. Conclusions There was a marked variation in AVS and SEM among different sites studied. AVS concentrations were generally lower in the surface sediments, while SEM concentrations slightly decreased with the depth. Higher concentrations of SEM found in the upper layers of the sediments confirm the earlier suggestions that this study area may suffer from increasing heavy metal pollution. Recommendations and Perspectives When monitoring environmental impacts by using AVS, the micro and large-scale spatial variation as well as vertical distribution need to be estimated to avoid misleading results. Both AVS and SEM concentrations in different sediment layers should be taken into account in assessing the potential impact of heavy metals on the biotic environment.     

Heavy metal in sediments of Ziya River in northern China: distribution,potential risks,and source apportionment

The concentration partitioning between the sediment particle and the interstitial water phase plays an important role in controlling the toxicity of heavy metals in aquatic systems. The aim of this study was to assess the sediment quality in a polluted area of the Ziya River, Northern China. The contamination potential and bioavailability of six metals were determined from the concentrations of total metals and the bioavailable fractions. The results showed that the concentrations of Cr, Cu, Ni, Zn, and Pb exceeded the probable effect concentration at several sites. The high geoaccumulation indices showed that the sediments were seriously contaminated by Cd. The ratio of acid-volatile sulfide (AVS) to simultaneously extracted metal (SEM) was higher than 1, which indicated that the availability of metals in sediments was low. The risk assessment of interstitial waters confirmed that there was little chance of release of metals associated with acid-volatile sulfide into the water column. Values of the interstitial water criteria toxicity unit indicated that none of the concentrations of the studied metals exceeded the corresponding water quality thresholds of the US Environmental Protection Agency. Positive matrix factorization showed that the major sources of metals were related to anthropogenic activities. Further, if assessments are based on total heavy metal concentrations, the toxicity of heavy metals in sediment may be overestimated.     

Relationship among parameters of lake polluted sediments evaluated by multivariate statistical analysis

In the attempt to assess the relationship and interdependency among sediment toxic pollutants, in particular heavy metals, polycyclic aromatic hydrocarbons (PAH), and linear alkyl sulfonates (LAS) and some of the sediment typical components: inorganic carbon (IC), organic material (OM) and acid volatile sulphides (AVS), multivariate techniques of statistical analysis have been applied to a set of chemical data obtained by the analysis of the sediments of the Trasimeno Lake, a central Italy lake characterized by a large surface (128 km(2)) and a low mean depth (about 4.5 m). The results of principal component analysis (PCA) show interrelationships between: OM content and PAH, Pb, and Cu concentrations of the sediments, LAS and AVS, and AVS and IC. The effect of the different sampling periods on sediment composition and contamination level, and the clustering of the sampling sites as a consequence of pollutant load are also shown. The principal component bi-plot of the variables and samples indicates that PAH have the greatest influence on the separation of samples in the different sampling periods.     

Fractionation and extractability of sulfur, iron and trace elements in sulfidic sediments

This study describes iron and sulfur fractionation, and the related extractability of selected trace elements (As, Cd, Cr, Cu, Ni, Pb and Zn) in estuarine sediments. The sediments were sulfidic, with moderately high concentrations of pore-water sulfide (200-600 micromol l(-1)) and acid-volatile sulfide (AVS; 9.9-129 micromol g(-1)). Pyrite-S concentrations increased with depth, with 63-251 micromol g(-1) at site W1 and 312-669 micromol g(-1) at site W2. The degree of sulfidisation was generally high (>80%), indicating that Fe may be limiting pyrite accumulation. The ratios of AVS to pyrite-S increased with sediment depth, as expected for the pyritisation of solid-phase AVS. Cadmium, Pb and Zn extractability in 1M HCl indicated that these elements are not significantly sequestered during pyritisation, whereas sequestration may be important for As, Cu and possibly Ni. Extractability trends for Cr suggest that diagenesis in sulfidic sediments may enhance Cr reactivity. Overall, replacement of AVS by pyrite during diagenesis may enhance the reactivity of Cd, Cr, Pb and Zn, whereas As, Cu and possibly Ni may be rendered less reactive.     

The effect of manipulating sediment pH on the porewater chemistry of copper- and zinc-spiked sediments

Spiking of sediment with metal cations that readily hydrolyse causes the sediment pH to decrease. Displaced iron and manganese also oxidise and hydrolyse, further lowering sediment pH. The lower pH of metal-spiked sediments requires a subsequent sediment neutralisation. This research compared the pH adjustment of Cu- and Zn-spiked sediments using single and multiple additions of 1M NaOH. Sediment pH, redox potential, and porewater metal concentrations were monitored over 40 days. Depth profiles were also measured to investigate stratification. A single pH adjustment to pH 7 and 8 initially counteracted the pH change caused by metal additions, however, pH continued to decrease slowly thereafter. Multiple pH adjustments diminished porewater Cu, Zn and Fe concentrations to a greater extent than a single pH adjustment, but the ongoing oxidative precipitation of porewater metals continued to consume OH(-) ions and impede pH maintenance. Displacement of high iron(II) concentrations and the opposing rates of iron(II) oxidative precipitation and bacterially-mediated iron(II) production, affected the partitioning of the added metals between the sediment and pore water. Despite similar pH over the spiked-metal concentration gradient following pH adjustment, sediments spiked with higher metal concentrations produced lower porewater Fe concentrations, possibly due to toxicity to iron(III) oxyhydroxide reducing bacteria. Distinct stratification of redox potential and dissolved Fe and Cu developed over a depth of 6cm during the 40-day equilibration period. Recommendations are provided on methods for preparing metal-spiked sediments in which the partitioning of metals between dissolved and particulate phases better resembles that of in situ (field) metal-contaminated sediments.     

Metal equilibration in laboratory-contaminated (spiked) sediments used for the development of whole-sediment toxicity tests

The equilibration and bioavailability of metals in laboratory-contaminated sediments have been investigated in order to provide better guidance on acceptable procedures for spiking sediments with metals for use in the development of whole-sediment toxicity tests. The equilibration rates of Cd, Cu, Ni and Zn spiked into three estuarine surface sediments with varying properties were investigated. Changes to sediment pH, redox potential, porewater and acid-soluble metals, acid-volatile sulfide and bacterial activity during equilibration, effects of temperature and disturbances following equilibration are reported. The addition of metals to sediments caused major decreases in pH and increases in redox potential as metals displaced iron(II) into the porewaters and added metals and iron (following oxidation) were hydrolyzed. The rates of equilibration of metals in porewaters varied considerably and were dependent on sediment and metal properties. For the oxic/sub-oxic sediments studied, metal-spikes of Cd, Cu, Ni and Zn appeared near equilibrium after 25-45, 10-15, 30-70 and 20-40 days, respectively. Acid-soluble metal concentrations decreased during the equilibration period indicating that the metals become more strongly associated with the sediments with time (less bioavailable). Bacterial activity was greatest in the sediment equilibrated at pH 7 and decreased following the addition of metals. During the equilibration period, bacterial activity increased in sediments equilibrated at pH 6, remained low in sediments at pH 8 and varied erratically in sediments at pH 7. Spiked sediments were shown to equilibrate more slowly at lower temperatures resulting in high porewater metal concentrations. Disturbances to equilibrated sediments because of sample manipulation caused significant iron(II) oxidation and losses of metals from porewaters. The importance of documenting spiking and equilibration procedures and carefully measuring and reporting sediment parameters is highlighted so that contaminant bioavailability and exposure pathways can be interpreted and organism sensitivity accurately determined. Recommendations are given for the preparation of metal-spiked sediments for toxicity testing purposes.     

Spatial distribution and ecological assessment of nickel in sediments of a typical small plateau lake from Yunnan Province,China

Nickel (Ni) in small plateau lake sediments plays an important role in influencing the quality of lake ecosystems with a high degree of endemism and toxicity. This paper focuses on the spatial distribution and ecological risks of nickel in the sediments of Jianhu Lake, a small plateau lake in China, and the influence of pH and total organic carbon (TOC) on nickel concentrations. The results showed that average total nickel concentrations were 138.99 ± 57.57 mg/kg (n = 38) and 184.31 ± 92.12 mg/kg (n = 60) in surface sediments (0–10 cm top layer) and sediment cores (0–75 cm depth), respectively, and that the residual fraction was the main form of nickel. Simultaneously, through a semivariogram model, strong spatial dependence among pH, TOC, and the oxidizable fraction was revealed, whereas total nickel, exchangeable and the weak acid soluble fraction, reducible fraction, and residual fraction showed moderate spatial dependence. The vertical distribution revealed that nickel accumulated mainly in the bottom 5 cm (70-75 cm) of the sediment layer and that the pH was higher there, whereas TOC was concentrated mainly in the top 5 cm of sediment. Using geoaccumulation and a potential ecological risk index, moderate nickel pollution and moderate risk levels were found in most surface sediments, but moderate nickel pollution and high risk levels were observed in most sediment cores. In addition, pH and TOC were found to have a strong effect on the distribution and concentration of nickel and its fractions in the small plateau lake. In summary, nickel posed a certain degree of pollution and ecological risk, which deserves attention in the sediments of small plateau lakes.

     

A comprehensive investigation and assessment of mercury in intertidal sediment in continental coast of Shanghai

The aims of this paper were to survey the total Hg levels and distribution character in intertidal sediment in continental coast of Shanghai, and identify the environment factors that might influence the sediment Hg concentrations, and to assess the pollution degree and potential ecological risk of Hg in sediment. Eighty-eight surface sediment samples and 18 sediment cores were collected for Hg contamination analysis. Physicochemical properties including Eh, particle size, content of total organic carbon (TOC), and acid volatile sulfide (AVS) were also measured. Index of geo-accumulation (I _geo) and potential ecological risk index were used respectively to assess the pollution levels and the ecological risk of sediment Hg. The average of total Hg concentrations in surface sediments was 107.4?±?90.9 ng/g with the range from 0 to 465.9 ng/g. Higher Hg concentrations were generally found in surface sediments near sewage outfalls and the mouth of rivers. Total Hg concentrations were significantly correlated with TOC (p?<?0.05) both in surface (r?=?0.24) and core (r?=?0.29) sediments, but not with the other environment factors (Eh, AVS, and particle size). Geo-accumulation index indicated that Hg contamination in intertidal sediments was generally at none to moderate degree, while potential ecological risk index demonstrated that the risk caused by Hg were at moderate to considerable level. Intertidal sediment in continental coast of Shanghai has generally been contaminated by Hg, and it might pose moderate to considerable risk to the local ecosystem. The Hg contamination is related more to the coastal pollution sources and complicated hydrodynamic and sedimentary conditions than the other environment factors studied.     

Processes controlling metal transport and retention as metal-contaminated groundwaters efflux through estuarine sediments

Factors affecting the transport and retention of Cd, Cr, Cu, Ni, Pb and Zn in acidic groundwaters as they pass through estuarine sediments were investigated using column experiments. Acidic groundwaters caused the rapid dissolution of iron sulfide (AVS) and other iron and manganese phases from sediments that are important for metal binding and buffering. Metal breakthrough to overlying water occurred in the order of Ni>Zn>Cd>Cu>Cr/Pb. Metal transport increased as the sediment permeability increased, reflecting the low resistance to flow caused by larger sand-sized particles and the decreased abundance of metal adsorption sites on these materials. Metal mobility increased as the groundwater pH decreased, as flow rate or metal concentrations increased, and as the exposure duration increased. Groundwater Cr and Pb were promptly attenuated by the sediments, the mobility of Cu was low and decreased rapidly as sediment pH increased above 4.5, while Cd, Ni and Zn were the most easily transported to the surface sediments and released to the overlying waters. For groundwaters of pH 3, metal migration velocities through sandy sediments were generally 0.5-2% (Cr, Pb), 1-6% (Cu) and 4-13% (Cd, Ni, Zn) of the total groundwater velocity (9-700 m/yr). The oxidative precipitation of Fe(II) and Mn(II) in the groundwaters did not affect metal mobility through the sediments. The results indicated that the efflux of acidic and metal-contaminated groundwater through estuarine sediments would affect organisms resident in sandy sediments more greatly than organisms resident in fine-grained, silty, sediments.     

The Role of a Salt Marsh Plant on Trace Metal Bioavailability in Sediments. Estimation By Different Chemical Approaches * (7 pp)

Goal, Scope and Background The presence or absence of vegetation can condition sediment characteristics. The main aim of this work was to investigate the influence of the sea rush Juncus maritimus on metal (Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) availability to organisms living on or in estuarine sediments, from Douro River (NW Portugal), by comparing the characteristics and chemical behaviour of rhizosediments (collected within the plant assemblage) and those of sediment (collected around the plant). In order to evaluate whether and how sediment characteristics condition the role of plants on metal availability, sandy and muddy sediments colonised by J. maritimus were studied in parallel. Methods Metal availability was estimated by enzymatic digestion with pepsin (ED), which may provide an estimate of metal availability to organisms living at estuarine sediments. Nevertheless, since no consensus exists yet on the most suitable methodologies to estimate metal bioavailability in sediments, two more conventional approaches, BCR sequential extraction (SE) and AVS/SEM model, were also used, in parallel, and the information these approaches provided was compared with that provided by ED. Total-recoverable metal contents were determined by atomic absorption spectrophotometry after sediment digestion using a high-pressure microwave system. Results and Discussion Plants could concentrate metals around its roots and rhizomes. In addition, they were capable of oxidizing (release of oxygen by the roots) the anaerobic medium surrounding their roots in muddy sediment (reducing AVS). As sulphide oxidation renders metals (Cd, Cu, Ni, Pb and Zn) into more soluble forms, according to the AVS/SEM model, metals from muddy sites would be more available in rhizosediment than in sediment. The SE approach led to a similar conclusion. Nevertheless, the results provided by ED pointed at opposite conclusion, particularly for Cd and Zn, indicating less availability at rhizosediments than in the surrounding sediment. ED results were interpreted as a consequence of an enrichment of the rhizosediment in organic ligands exuded by the roots or liberated by dead plants. The effect of complexation of metals by organic compounds, which ED could not decompose/dissolve, seemed to overcome that caused by sediment oxidation. In general, a comparison of the information about metal availability by ED, SE, AVS/SEM, showed that it did not always match and in few cases it was even contradictory. Conclusion and Outlook Therefore, a thorough evaluation of the metal availability in sediments requires a combination of different chemical approaches, so as to take into consideration differences in ways of organism exposure (interstitial water and/or ingestion of sediment particles). - * The basis of this peer-reviewed paper is a presentation at the 9th FECS Conference on 'Chemistry and Environment', 29 August to 1 September 2004, Bordeaux, France.     

Long-term effects of submergence and wetland vegetation on metals in a 90-year old abandoned Pb-Zn mine tailings pond

A Pb-Zn tailings pond, abandoned for approximately 90 years, has been naturally colonized by Glyceria fluitans and is an excellent example of long-term metal retention in tailings ponds under various water cover and vegetation conditions. Shallow/intermittently flooded areas (dry zone) were unvegetated and low in organic matter (OM) content. Permanently flooded areas were either unvegetated with low OM, contained dead vegetation and high OM, or living plants and high OM. It was expected that either water cover or high OM would result in enhanced reducing conditions and lower metal mobility, but live plants would increase metal mobility due to root radial oxygen loss. The flooded low OM tailings showed higher As and Fe mobility compared with dry low OM tailings. In the permanently flooded areas without live vegetation, the high OM content decreased Zn mobility and caused extremely high concentrations of acid-volatile sulfides (AVS). In areas with high OM, living plants significantly increased Zn mobility and decreased concentrations of AVS, indicating root induced sediment oxidation or decreased sulfate-reduction. This is the first study reporting the ability of wetland plants to affect the metal mobility and AVS in long-term (decades), unmanaged tailings ponds.     

Quantification of bioavailable nickel in sediments and toxic thresholds to Hyalella azteca

Bioaccumulation and chronic toxicity of nickel (Ni) to Hyalella azteca in Ni-spiked sediments was strongly affected by the source of sediment used. The total range in LC50s on a sediment concentration basis ranged over 20 fold. Differences in Ni toxicity generally matched differences in Ni bioaccumulation, and toxicity expressed on a body concentration basis varied less than three fold. Body concentrations, therefore, provide a much more reliable prediction of Ni toxicity in sediments than do concentrations in the sediment. Ni in overlying water was also a reliable predictor of Ni toxicity, but only in tests conducted in Imhoff settling cones with large (67:1) water to sediment ratios. Overlying water LC50s for tests in beakers varied 18 fold. Sediment and body concentrations of Ni tolerated by Hyalella were slightly higher in cones than in beakers. Reproduction was not affected significantly by Ni at concentrations below the LC50 and 10-week EC50s for survival and biomass production (including survival, growth and reproduction) were only marginally lower than 4-week EC50s (survival and growth only).     

Heavy metal distribution in sediments and ecological risk assessment: The role of diagenetic processes in reducing metal toxicity in bottom sediments

This paper describes the heavy metal distributions in river and lagoonal sediments of Jacarepaguá Basin, Rio de Janeiro, Brazil. The occurrence of metal phase translocation from the reducible to the oxidizable was observed for Fe, Mn and Ni, from the fluvial environment to the lagoonal. Cu was mainly associated with the oxidizable phase while Zn and Pb were mainly associated with the reducible phase in both environments. It has been demonstrated that metal sulfide formation and complexation by organic complexes are very important aspects in terms of toxicity reduction. By means of a risk assessment methodology, based on available sediment data, it was demonstrated that the lagoonal system is exposed to a low potential ecological risk and that Zn was the metal of greater concern with respect to the system pollution.     

Temporal variation of trace metal geochemistry in floodplain lake sediment subject to dynamic hydrological conditions

Climate change and land use may significantly influence metal cycling in dynamic river systems. We studied temporal variation of sediment characteristics in a floodplain lake, including concentrations of dissolved organic carbon, acid volatile sulfide and trace metals. The sampling period included a severe winter inundation and a dramatic water level drop during summer. Temporal changes were interpreted using multivariate analysis and chemical equilibrium calculations. Metal concentrations in sediment increased with depth, indicating a gradual improvement of sediment quality. In contrast, dissolved metal concentrations were highest in top layers due to mobilization from oxyhydroxides and precipitation with sulfides in deeper layers. Inundation had a mobilizing effect as it stimulated resuspension and oxygenation of sediment top layers. Water table lowering combined with organic matter decomposition led to immobilization due to sulfide formation. The chemistry of the sediments was consistent with model calculations, especially for macro-elements. The results illustrate the importance of seasonality for metal risk assessment.     

Effects of sediment composition on inorganic mercury partitioning, speciation and bioavailability in oxic surficial sediments

Artificially prepared sediments were used to assess the effects of sediment composition on inorganic Hg partitioning, speciation and bioavailability. Organic coating in sediment greatly increased the Hg partitioning and the amount of bioavailable Hg bound with the clay and the Fe and Mn oxides, but had little effect on that bound with the quartz and calcium carbonate as a result of weaker binding of humic acids and fulvic acids. The clay content increased the concentration of Hg in the sediments but inhibited the gut juice extraction due to the strong binding of Hg-organic matter (OM) complexes. Most Hg in the sediments was complexed by OM (mainly distributed in the organo-complexed phase and the strongly complexed phase), and the Hg-OM complexes (especially Hg in the strongly complexed phase) in sediments contributed much to gut juice extraction. Redistribution of Hg-OM complexes between sediments and gut juices may occur during gut juice extraction and modify Hg bioavailability and speciation in sediments.     

Sampling method, storage and pretreatment of sediment affect AVS concentrations with consequences for bioassay responses

Sediment treatment and sediment storage may alter sediment toxicity, and consequently biotic response. Purpose of our study was to combine these three aspects (treatment-toxicity-biotic response) in one integrated approach. We used Acid Volatile Sulfide (AVS) concentrations as a proxy of the disturbance of the sediment. AVS and Simultaneously Extracted Metal (SEM) concentrations were compared to bioassay responses with the freshwater benthic macroinvertebrate Asellus aquaticus. Storage conditions and sediment treatment affected AVS but not SEM levels. AVS can be used as a proxy for sediment disturbance. The best way to pretreat the sediment for use in a bioassay in order to maintain initial AVS conditions was to sample the sediment with an Ekman grab, immediately store it in a jar without headspace, and freeze it as soon as possible. In a survey using seven different sediments, bioassay responses of A. aquaticus were correlated with SEM and AVS characteristics.     

Toxicity and heavy metal contamination of surficial sediments from the Bay of Thessaloniki (Northwestern Aegean Sea) Greece

Surficial sediments (the fraction < 2000 microm) from the Bay of Thessaloniki, in the Northwestern Aegean Sea, Greece were examined for heavy metal and organic carbon contents, as well as for acute LUMIStox toxicity of pore waters (PWs), wet sediment elutriates (WSEs) and dry sediment elutriates (DSEs) obtained from the solid material remaining after PW extraction. WSEs where not toxic. EC20/50 values could be measured in some DSE and PW samples. In all sediment samples, the DSE toxicity was greater than the corresponding PW toxicity. Sediment concentrations of total and labile Cd, Pb, Cu, Cr, Zn, Mn, Ni and Fe were determined and evaluated in relation to sediment quality guidelines. Pollution levels ranged from low to high for certain metals. A misfit between sediment toxicities calculated from heavy metal concentrations and those biologically measured was observed. Toxicity values were in general poorly correlated with sediment's heavy metal or organic carbon content. As significant correlation was however found between the DSE toxicity with total Ni and labile Fe, as well as for the PW toxicity with total Ni, labile Fe and labile Cr.