Sorption of Cr(VI) from dilute solutions and wastewater by live and pretreated biomass of Aspergillus flavus

Sorption of Cr(VI) was carried out from dilute solutions using live and pretreated biomass in a batch mode. Effects of agitation time, adsorbent dosage and pH were examined. The autoclaved biomass that showed maximum adsorption capacity (Q(0)=0.335 mg g(-1)) was used as an adsorbent in column studies. The optimized flow rate of 2.5 ml min(-1) and bed height 10 cm were used to determine the effect of metal ion concentration on removal of Cr(VI). Applying the BDST model to calculate the adsorption capacity (N(0)) of column, which showed 4.56 x 10(-5), 7.28 x 10(-5), 6.89 x 10(-5), 3.07 x 10(-5), 2.80 x 10(-5)mg g(-1) for 4, 8, 12, 16 and 20 mg dm(-3) of Cr(VI), respectively. Batch sorption proved to be more efficient than the column sorption and hence batch sorption was used to remove Cr(VI) from a textile dyeing industry wastewater. The phytotoxic effect of treated and untreated wastewater was studied against Zea mays. Toxicity was reduced by 50% in the treated effluent.     

Removal of Cr(VI) and humic acid by using TiO2 photocatalysis

The removal efficiencies of Cr(VI) and HA, using a TiO(2)-mediated photocatalytic process, were investigated with variations in the pH, TiO(2) dosage and Cr(VI)/HA ratio. During the photocatalytic reaction, the total removal of Cr(VI) occurred through adsorption onto TiO(2), as well as its reduction to Cr(III). However, oxidation and adsorption were identified as important removal processes for the treatment of HA. Due to the anionic type adsorption onto TiO(2) and its acid-catalyzed photocatalytic reduction, the removal of Cr(VI) decreased with increasing pH, while that of HA increased with increasing pH. The TiO(2) dosage was also an important parameter for the removal of Cr(VI). As the TiO(2) dosage was increased to 2.5 g l(-1), the removal of Cr(VI) was continuously enhanced, but decreased at dosages above 3 g l(-1) due to the increased blockage of the incident UV light used for the photocatalytic reaction. The removal of Cr(VI) was greatly enhanced when the system contained both HA and Cr(VI) compared to Cr(VI) alone. Also, the removal of HA was greatly enhanced when the system contained both HA and Cr(VI) compared to HA alone. The removal of Cr(VI) was continuously enhanced as the HA concentration gradually increased; however, no further increase was observed above 20 mg l(-1) HA due to the increased absorption of the UV light. This result supports that the photocatalytic reaction, with illuminated TiO(2), could be applied to more effectively treat wastewater containing both Cr(VI) and HA than that containing a single species only.     

高比表面积活性炭的制备及对Cr(Ⅵ)吸附的研究

以椰树壳为原料,运用水蒸汽和二氧化碳复合物理活化法在4 h内制备了2 162.84 m2/g的高比表面积活性炭,其孔径分布范围为1.1~2.5 nm。应用此吸附剂考察了溶液pH、吸附剂用量、接触时间和初始浓度对Cr(VI)离子吸附效果的影响,并讨论了固定吸附床中不同溶液流量对Cr(VI)去除效果的影响。结果表明:在温度为298 K、溶液pH为1.96、吸附剂用量为0.10 g、铬离子初始浓度为100 mg/L与接触时间为70 min的条件下,活性炭对铬离子具有较高的吸附容量,去除率高达99.32%;铬离子在吸附床中的穿透曲线具有陡峭的传质锋面,但随着铬离子溶液流量的增大脱除果率降低。     

Kinetic, equilibrium isotherm and thermodynamic studies of Cr(VI) adsorption onto low-cost adsorbent developed from peanut shell activated with phosphoric acid

A particular agricultural waste, peanut shell, has been used as precursor for activated carbon production by chemical activation with H₃PO₄. Unoxidized activated carbon was prepared in nitrogen atmosphere which was then heated in air at a desired temperature to get oxidized activated carbon. The prepared carbons were characterized for surface area, surface morphology, and pore volume and utilized for the removal of Cr(VI) from aqueous solution. Batch mode experiments were conducted to study the effects of pH, contact time, particle size, adsorbent dose, initial concentration of adsorbate, and temperature on the adsorption of Cr(VI). Cr(VI) adsorption was significantly dependent on solution pH, and the optimum adsorption was observed at pH 2. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used to analyze the kinetic data obtained at different initial Cr(VI) concentrations. The adsorption kinetic data were described very well by the pseudo-second-order model. Equilibrium isotherm data were analyzed by the Langmuir, Freundlich, and Temkin models. The results showed that the Langmuir adsorption isotherm model fitted the data better in the temperature range studied. The adsorption capacity which was found to increase with temperature showed the endothermic nature of Cr(VI) adsorption. The thermodynamic parameters, such as Gibb’s Free energy change (ΔG°), standard enthalpy change (ΔH°), and standard entropy change (ΔS°) were evaluated.     

Characterization of primary precipitate composition formed during co-removal of Cr(VI) with Cu(II) in synthetic wastewater

BACKGROUND, AIMS AND SCOPE: Hexavalent chromium [Cr(VI)] cannot react with either carbonate or hydroxide to form chromium precipitates. However, by using a precipitation technology to treat plating wastewater containing Cr(VI), Cu(II), Ni(II) and Zn(II), approximately 78% of Cr(VI) (initial 60 mg/L) was co-removed with the precipitation of Cu(II), Ni(II) and Zn(II) (each 150 mg/L) by dosing with Na2CO3 (Sun 2003). Direct precipitation by forming Cu(II)-Cr(VI) precipitates followed by adsorption of Cr(VI) onto freshly formed Cu-precipitates was subsequently found to be the main mechanism(s) involved in Cr(VI) co-removal with Cu(II) precipitation by dosing Na2CO3 stepwise to various pH values (Sun et al. 2003). This study was. carried out to further characterize the formation of primary precipitates during the early stages of copper precipitation and simultaneous removal of Cr(VI) with Cu(II). METHODS: Test metal-solutions were prepared with industrial grade chemicals: CuCl2 x 2H2O, Na2SO4 and K2Cr2207. NaCO3 was added drop-wise to synthetic metal-solution to progressively increase pH. For each pH increment, removal of soluble metals was detected by atomic absorption spectrophotometer (AAS) and surface morphology of precipitates was analyzed by scanning electron microscope (SEM). To further characterize the formation of primary precipitates, a series of MINEQL+ thermodynamic calculations/analyses and equilibrium calculations/ analyses were conducted. RESULTS AND DISCUSSION: MINEQL+ thermodynamic calculation indicated that, for a system containing 150 mg/L Cu(II) and 60 mg/L Cr(VI) with gradual Na2CO3 dosing, if any precipitates can be formed at pH 5.0 or lower, it should be in the form of CuCrO4. Comparison tests using systems containing the same equivalent of Cu(II) plus Cr(VI) and Cu(II) plus SO4(2-) showed that the precipitation occurred at a pH of around 5.0 in the Cu(II)-Cr(VI) system and around 6.0 in the Cu(II)-SO4(2-) system. The discrepancy of the precipitation was indeed caused by the formation of Cu-Cr precipitates. The initiation of copper removal at pH around 5.0 for the Cu-Cr co-removal test was not attributable to the formation of Cu-CO3 precipitates, instead, it was most likely through the formation of insoluble Cu-Cr precipitates, such as CuCrO4 and CuCrO4 x 2Cu(OH)2. Experimental tests, equilibrium calculations, MINEQL+ thermodynamic calculations and surface morphologies for systems using higher concentrations of Cu(II) and Cr(VI) further verified the most probable composition of primary precipitates is copper-chromate. CONCLUSION: In the Cu-Cr co-removal test with Na2O3 dosing to increase pH and induce metal precipitation, copper-chromate precipitates are the primary precipitates produced and contribute to the initial simultaneous removal of copper and chromium.     

Chromium(VI) sorptive removal from aqueous solutions by nanocrystalline akaganèite

In this study, akaganeite (beta-FeO(OH)) an ironoxyhydroxide material, was used as a low-cost potential adsorbent for the removal of hexavalent chromium from aqueous solutions. The influence of agitation speed, solution pH, initial chromium concentration, sorbent concentration and temperature were evaluated at batch kinetic runs. It was shown that the solid diffusion model, in comparison to simple reaction kinetic models, described better the sorption kinetics. Freundlich and Frumkin isotherm best fitted the equilibrium results. Akaganeite presented a sorption capacity approximately 80 mg Cr(VI) g(-1), under the conditions studied. Flotation was used as a downstream process for the effective removal of the loaded material.     

Comparative and competitive adsorption of Cr(VI), As(III), and Ni(II) onto coconut charcoal

This study evaluates the behavior of coconut charcoal (AC) to adsorb Cr(VI), As(III), and Ni(II) in mono- and multicomponent (binary and ternary) systems. Batch experiments were carried out for mono- and multicomponent systems with varying metal ion concentrations to investigate the competitive adsorption characteristics. The adsorption kinetics followed the mechanism of the pseudo-second-order equation in both single and binary systems, indicating chemical sorption as the rate-limiting step of adsorption mechanism. Equilibrium studies showed that the adsorption of Cr(VI), As(III), and Ni(II) followed the Langmuir model and maximum adsorption capacities were found to be 5.257, 0.042, and 1.748 mg/g, respectively. In multicomponent system, As(III) and Ni(II) adsorption competed intensely, while Cr(VI) adsorption was much less affected by competition than As(III) and Ni(II). With the presence of Cr(VI), the adsorption capacities of As(III) and Ni(II) on AC were higher than those in single system and the metal sorption followed the order of Ni(II)?>?As(III)?>?Cr(VI). The results from the sequential adsorption–desorption cycles showed that AC adsorbent held good desorption and reusability.     

Use of activated dry flowers (ADF) of Alstonia Scholaris for chromium (Vl) removal: equilibrium, kinetics and thermodynamics studies

In this study, a natural adsorbent (activated dry flowers (ADF)) was prepared from plant-derived waste biomass by chemical activation and employed for chromium (VI) removal from aqueous medium using experimental batch technique. Experiments were carried out as function of adsorbent dosage, pH, and contact time. The maximum chromium (Vl) removal was observed at initial pH 3 (~94 % removal). The equilibrium data was fitted well to Langmuir isotherm. The adsorption capacity of ADF was found to be 4.40 (mg chromium (Vl)/g) which was comparable to the adsorption capacity of some other adsorbents documented. Among various kinetic models applied, pseudo second-order model was found to explain the kinetics of chromium (VI) adsorption most effectively (R ² >0.99). Thermodynamic parameters such as ΔG, ΔS, and ΔH shows that adsorption process was spontaneous and endothermic at all the concentration ranges studied. Desorption of chromium (Vl) with 2 N NaOH was effective (~71 %) and, hence, there exists the possibility of recycling the ADF. The major advantages of using ADF as an adsorbent are due to its effectiveness in reducing the concentration of chromium (Vl) to very low levels. It requires little processing and is reversible as well as eco-friendly in contrast to traditional methods.     

Biosorption of Cr(VI) and Zn(II) ions from aqueous solution onto the solid biodiesel waste residue: mechanistic, kinetic and thermodynamic studies

In this present study, the biosorption of Cr(VI) and Zn(II) ions from synthetic aqueous solution on defatted J atropha oil cake (DJOC) was investigated. The effect of various process parameters such as the initial pH, adsorbent dosage, initial metal ion concentration and contact time has been studied in batch-stirred experiments. Maximum removal of Cr(VI) and Zn(II) ions in aqueous solution was observed at pH 2.0 and pH. 5.0, respectively. The removal efficiency of Cr(VI) and Zn(II) ions from the aqueous solution was found to be 72.56 and 79.81 %, respectively, for initial metal ion concentration of 500 mg/L at 6 g/L dosage concentration. The biosorbent was characterized by Fourier transform infrared, scanning electron microscopy and zero point charge. Equilibrium data were fitted to the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models and the best fit is found to be with the Freundlich isotherm for both Cr(VI) and Zn(II) metal ions. The kinetic data obtained at different metal ion concentration have been analysed using the pseudo-first-order, pseudo-second-order and intraparticle diffusion models and were found to follow the pseudo-second-order kinetic model. The values of mass transfer diffusion coefficients (D _e) were determined by Boyd model and compared with literature values. Various thermodynamic parameters, such as ΔG°, ΔH° and ΔS°, were analysed using the equilibrium constant values (K _e) obtained from experimental data at different temperatures. The results showed that biosorption of Cr(VI) and Zn(II) ions onto the DJOC system is more spontaneous and exothermic in nature. The results indicate that DJOC was shown to be a promising adsorbent for the removal of Cr(VI) and Zn(II) ions from aqueous solution.     

Selective removal of Cr(VI) from aqueous solution by adsorption on mangosteen peel

Mangosteen peel, rich in polyphenolic compounds, was used to prepare the adsorbent exhibiting highly selective adsorption for Cr(VI) over other metal ions such as Pb²⁺, Fe³⁺, Zn²⁺, Cd²⁺, and Cr³⁺ at the pH values of 1～4. The chemical modification method proposed by using calcium hydroxide is quite cost-effective and ecofriendly without using any toxic reagents or causing any secondary pollution. The adsorption isotherm results revealed that the adsorption of Cr(VI) on the gel fit well the Langmuir adsorption model, and the maximum adsorption capacity for Cr(VI) at pH levels 1, 2, 3, and 4 was evaluated to be 2.46, 2.44, 1.99, and 2.14 mol/kg, respectively. The adsorption mechanism for Cr(VI) on the saponified gel was verified to follow an esterifiaction reaction coupled with the reduction of Cr(VI) to Cr(III) in which H⁺ plays a role of promoter. Thus, modified mangosteen peel gel has the prominent selectivity and low cost for Cr(VI) removal.     

Enhanced adsorption of hexavalent chromium by a biochar derived from ramie biomass (<Emphasis Type="Italic">Boehmeria nivea</Emphasis> (L.) Gaud.) modified with β-cyclodextrin/poly(L-glutamic acid)

This paper explored biochar modification to enhance biochar’s ability to adsorb hexavalent chromium from aqueous solution. The ramie stem biomass was pyrolyzed and then treated by β-cyclodextrin/poly(L-glutamic acid) which contained plentiful functional groups. The pristine and modified biochar were characterized by FTIR, X-ray photoelectron spectroscopy, specific surface area, and zeta potential measurement. Results indicated that the β-cyclodextrin/poly(L-glutamic acid) was successfully bound to the biochar surface. Batch experiments were conducted to investigate the kinetics, isotherm, thermodynamics, and adsorption/desorption of Cr(VI). Adsorption capacities of CGA-biochar were significantly higher than that of the untreated biochar, and its maximum adsorption capacity could reach up to 197.21 mg/g at pH 2.0. Results also illustrated that sorption performance depended on initial solution pH; in addition, acidic condition was beneficial to the Cr(VI) uptake. Furthermore, the Cr(VI) uptake was significantly affected by the ion strength and cation species. This study demonstrated that CGA-biochar could be a potential adsorbent for Cr(VI) pollution control.     

Leaching behavior of Cr(III) in stabilized/solidified soil

The leaching behavior of chromium was studied using batch leaching tests, surface complexation modeling and X-ray absorption near edge structure (XANES) spectroscopy. A contaminated soil sample containing 1330 mg-Cr kg(-1) and 25600 mg-Fe kg(-1) of dry soil was stabilized/solidified (S/S) with 10% cement, 25% cement, 10% lime and a mixture of 20% flyash and 5% lime. The XANES analysis showed that Cr(III) was the only Cr species in untreated soil and S/S-treated samples. The leachate Cr concentration determined using the toxicity characteristic leaching procedure (TCLP) was reduced from 5.18 mg l(-1) for untreated soil to 0.84 mg l(-1) for the sample treated with 25% cement. The Cr leachability in untreated and treated soil samples decreased dramatically as the pH increased from 3 to 5, remained at similar levels in the pH range between 5 and 10.5, and further decreased at pH>10.5. Modeling results indicated that the release of Cr(III) was controlled by adsorption on iron oxides at pH<10.5, and by precipitation of Ca(2)Cr(2)O(5).6H(2)O at pH>10.5.     

Chromium species behaviour in the activated sludge process

The purpose of this research was to compare trivalent chromium (Cr(III)) and hexavalent chromium (Cr(VI)) removal by activated sludge and to investigate whether Cr(VI) reduction and/or Cr(III) oxidation occurs in a wastewater treatment system. Chromium removal by sludge harvested from sequencing batch reactors, determined by a series of batch experiments, generally followed a Freundlich isotherm model. Almost 90% of Cr(III) was adsorbed on the suspended solids while the rest was precipitated at pH 7.0. On the contrary, removal of Cr(VI) was minor and did not exceed 15% in all experiments under the same conditions. Increase of sludge age reduces Cr(III) removal, possibly because of Cr(III) sorption on slime polymers. Moreover, the decrease of suspended solids concentration and the acclimatization of biomass to Cr(VI) reduced the removal efficiency of Cr(III). Batch experiments showed that Cr(III) cannot be oxidized to Cr(VI) by activated sludge. On the contrary, Cr(VI) reduction is possible and is affected mainly by the initial concentration of organic substrate, which acts as electron donor for Cr(VI) reduction. Initial organic substrate concentration equal to or higher than 1000 mgl(-1) chemical oxygen demand permitted the nearly complete reduction of 5 mgl(-1) Cr(VI) in a 24-h batch experiment. Moreover, higher Cr(VI) reduction rates were obtained with higher Cr(VI) initial concentrations, expressed in mg Cr(VI) g(-1) VSS, while decrease of suspended solids concentration enhanced the specific Cr(VI) reduction rate.     

Effect of amorphous silica and silica sand on removal of chromium(VI) by zero-valent iron

The effect of two surfaces (amorphous silica and silica sand) on the reduction of chromium(VI) by zero-valent iron (Fe(0)) was investigated using batch reactors. The amendment of both surfaces significantly increased the rate and extent of Cr(VI) removal. The rate enhancement by amended surfaces is presumed to result from scavenging of Fe(0)-Cr(VI) reaction products by the provided surfaces, which minimized surface deactivation of Fe(0). The rate enhancing effect was greater for silica compared to sand, and the difference is attributed to silica's higher surface area, greater affinity for reaction products and pH buffering effect. For a given mass of Fe(0), the reactivity and longevity of Fe(0) to treat Cr(VI) increased with increasing dose of silica. Elemental analyses of the reacted iron and silica revealed that chromium removed from the solution was associated with both surfaces, with its mass distribution being approximately 1:1 per mass of iron and silica. The overall result suggests reductive precipitation was a predominant Cr(VI) removal pathway, which involves initial reduction of Cr(VI) to Cr(III), followed by formation of Cr(III)/Fe(III) hydroxides precipitates.     

Comparative study of chromium biosorption by red, green and brown seaweed biomass

Dried biomass of the macroalgae Fucus vesiculosus and Fucus spiralis (brown), Ulva spp. (comprising Ulva linza, Ulva compressa and Ulva intestinalis) and Ulva lactuca (green), Palmaria palmata and Polysiphonia lanosa (red) were studied in terms of their chromium biosorption performance. Metal sorption was highly pH dependent with maximum Cr(III) and Cr(VI) sorption occurring at pH 4.5 and pH 2, respectively. Extended equilibrium times were required for Cr(VI) binding over Cr(III) binding (180 and 120min, respectively) thus indicating possible disparities in binding mechanism between chromium oxidation states. The red seaweed P. palmata revealed the highest removal efficiency for both Cr(III) and Cr(VI) at low initial concentrations. However, at high initial metal concentrations F. vesiculosus had the greatest removal efficiency for Cr(III) and performed almost identically to P. lanosa in terms of Cr(VI) removal. The Langmuir Isotherm mathematically described chromium binding to the seaweeds where F. vesiculosus had the largest q(max) for Cr(III) sorption (1.21mmol g(-1)) and P. lanosa had the largest Cr(VI) uptake (0.88mmol g(-1)). P. palmata had the highest affinity for both Cr(III) and Cr(VI) binding with b values of 4.94mM(-1) and 8.64mM(-1), respectively. Fourier transform infrared analysis revealed interactions of amino, carboxyl, sulphonate and hydroxyl groups in chromium binding to Ulva spp. The remaining seaweeds showed involvement of these groups to varying degrees as well as ether group participation in the brown seaweeds and for Cr(VI) binding to the red seaweeds.     

Investigation of Cr(VI) reduction in continuous-flow activated sludge systems

The aim of this research was to investigate hexavalent chromium, Cr(VI), reduction by activated sludge and to evaluate the use of continuous-flow activated sludge systems for the treatment of Cr(VI)-containing wastewater. Three series of experiments were conducted using two parallel lab-scale activated sludge systems. During the first experiment, one system was used as a control, while the other received Cr(VI) concentrations equal to 0.5, 1, 3 and 5mg l(-1). For all concentrations added, approximately 40% of the added Cr(VI) was removed during the activated sludge process. Determination of chromium species in the dissolved and particulate phase revealed that the removed Cr(VI) was sorbed by the activated sludge flocs mainly as trivalent chromium, Cr(III), while the residual chromium in the dissolved phase was mainly detected as Cr(VI). Activated sludge ability to reduce Cr(VI) was independent of the acclimatization of biomass to Cr(VI) and it was not affected by the toxic effect of Cr(VI) on autotrophic and heterotrophic microorganisms. During the second experiment, both systems were operated under two different hydraulic residence time (theta equal to 20 and 28h) and three different initial organic substrate concentration (COD equal to 300, 150 and 0mg l(-1)). Cr(VI) reduction was favored by an increase of theta, while it was limited by influent COD concentration. Finally, at the last experiment the effect of anoxic and anaerobic reactors on Cr(VI) reduction was investigated. It was observed that the use of an anoxic zone or an anaerobic-anoxic zone ahead of the aerobic reactor favored Cr(VI) reduction, increasing mean percentage Cr(VI) reduction to almost 80%.     

Chromium (VI) remediation in aqueous solution by waste products (peel and seed) of mango (Mangifera indica L.) cultivars

The surface group characteristics of mango cultivar peels and seeds were evaluated by infrared spectra, PZC, and functional group composition. The adsorption/reduction of chromium (VI) in aqueous solutions was investigated by varying pH, contact time, initial Cr(VI) concentration, and adsorbent amount. The results show that both peel and seed powders of the mango cultivars showed significant adsorption/reduction capacity for Cr(VI) and that the desorption process obeys pseudo-second-order kinetics. Optimal adsorption occurred at pH 1.0, using a Cr(VI) concentration of 100 mg/L. On average, at pH 1.0, and a concentration of 3 g/L, the maximum adsorption/reduction capacity of Cr(VI) was 83% (peels 76%, seeds 90%). Of the mango powders tested, the most efficient were Tommy seed (100%) and Coite peel (98%) followed by Coite seed (96%) and Tommy peel powders (95%). The adsorption/reduction of Cr(VI) was complete (100%) by the mango seed, in comparison to the peel powders (97%) after 180 min. The data indicates that mango waste products, such as seed and peel powders, are both excellent candidates for the remediation of Cr(VI) from aqueous systems and due to the higher concentration of gallates and galloyl glucosides, the mango seed powders should be the powders of choice for future remediation projects.

     

Cr(VI) removal from synthetic wastewater using coconut shell charcoal and commercial activated carbon modified with oxidizing agents and/or chitosan

In this study, the technical feasibility of coconut shell charcoal (CSC) and commercial activated carbon (CAC) for Cr(VI) removal is investigated in batch studies using synthetic electroplating wastewater. Both granular adsorbents are made up of coconut shell (Cocos nucifera L.), an agricultural waste from local coconut industries. Surface modifications of CSC and CAC with chitosan and/or oxidizing agents, such as sulfuric acid and nitric acid, respectively, are also conducted to improve removal performance. The results of their Cr removal performances are statistically compared. It is evident that adsorbents chemically modified with an oxidizing agent demonstrate better Cr(VI) removal capabilities than as-received adsorbents in terms of adsorption rate. Both CSC and CAC, which have been oxidized with nitric acid, have higher Cr adsorption capacities (CSC: 10.88, CAC: 15.47 mg g(-1)) than those oxidized with sulfuric acid (CSC: 4.05, CAC: 8.94 mg g(-1)) and non-treated CSC coated with chitosan (CSCCC: 3.65 mg g(-1)), respectively, suggesting that surface modification of a carbon adsorbent with a strong oxidizing agent generates more adsorption sites on their solid surface for metal adsorption.     

Montmorillonite-Cu(II)/Fe(III) oxides magnetic material as adsorbent for removal of humic acid and its thermal regeneration

In this work, the adsorption features of montmorillonite and the magnetic properties of Cu(II)/Fe(III) oxides were combined in a material to produce magnetic adsorbent, which can be separated from the medium by a simple magnetic process after adsorption. The magnetic material is effective for the removal of humic acid. At pH 6.1, 96% removal was observed from 4.4 mg l(-1) humic acid solution containing 0.02 M NaCl. The adsorption is pH and ionic strength dependent. Adsorption is favored at lower pH values and dissolved NaCl can enhance the adsorption. The adsorption mechanism of humic acid to the magnetic material was suggested to be the ligand exchange reaction between carboxylic groups of humic acid molecules and the magnetic material surface. The magnetic material can be thermally regenerated. The temperature and time required to achieve good regeneration efficiency were determined to be 300 degrees C and 3 h, respectively. The regenerated adsorbent is still magnetic and approximately has as high specific saturation magnetization and good adsorption capacities as the as-prepared adsorbent.